Improved frontend handling.
Frontend now remains open at all times, with signal lock, snr & signal level
polled from Interupt.
Updated driver for DM04/QQBOX USB DVB-S BOXES to version 1.70.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you suspend and resume during video capture, the video colours
are corrupted on resume. This is because the sensor is being unconditionally
powered off during the resume path.
Only power down during resume if the camera is not in use, and correctly
reconfigure the sensor during resume.
Fixes http://dev.laptop.org/ticket/10190
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although cx231xx has a very good IR support, already supported by
mceusb driver, some designs decided to add a separate I2C
microcontroller chip in order to handle IR.
Due to that, add a glue to ir-kbd-i2c is needed, in order to support
those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By comparing the traffic between Pixelview (cx23102-based and Kworld
(saa7134-based), the only difference is at register 0xd5. After some
tests, It seems that it is used to change mode between serial and parallel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the trivial bits to mb86a20s. As the driver won't touch
at the channel/layer parameters, this may not be enough for
receiving all channels, especially ISDB-Tsb, but the driver worked
properly for receiving video channels on my tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On our tests with Leadership ISDBT, the s921 frontend were not work. As its
design contained some weird things, it ended to be easier to just re-write
it, getting another frontend as an example (cx24123).
As the old s921 driver weren't used, there's no regression. Some info from
the old frontend were used as a way to double check the behavior that were
noticed on the USB dumps retrieved from Leadership driver.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring_buffer: Off-by-one and duplicate events in ring_buffer_read_page
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/microcode: Fix double vfree() and remove redundant pointer checks before vfree()
arm: export dma_set_coherent_mask
While a regression was fixed with commit 710224fa27 (arm: fix
"arm: fix pci_set_consistent_dma_mask for dmabounce devices"), a
new one was introduced as dma_set_coherent_mask wasn't exported
for modules. This patch takes care for this issue.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst. Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'nommu-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/nommu-2.6:
nommu: Provide stubbed alloc/free_vm_area() implementation.
nommu: Fix up vmalloc_node() symbol export regression.
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fbdev: sh_mobile_lcdc: increase maximum framebuffer size to support 1080p
video: imxfb: Fix the maximum value for yres
fb: fix overlapping test off-by-one.
fbdev: sh-mobile: retrieve and propagate display sizes from EDID
fbdev: sh-mobile: restore display size configuration
LCDC hardware can support 1920x1080 formats, adjust the driver to cover them.
Besides, instead of guessing some "reasonable" validity checks, only verify
values in .fb_check_var(), that we are sure, we cannot support.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
MX27 and MX25 have 10 bits in the YMAX field of LCDC Size Register.
Fix the maximum value for yres.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In arch/x86/kernel/microcode_intel.c::generic_load_microcode()
we have this:
while (leftover) {
...
if (get_ucode_data(mc, ucode_ptr, mc_size) ||
microcode_sanity_check(mc) < 0) {
vfree(mc);
break;
}
...
}
if (mc)
vfree(mc);
This will cause a double free of 'mc'. This patch fixes that by
just removing the vfree() call in the loop since 'mc' will be
freed nicely just after we break out of the loop.
There's also a second change in the patch. I noticed a lot of
checks for pointers being NULL before passing them to vfree().
That's completely redundant since vfree() deals gracefully with
being passed a NULL pointer. Removing the redundant checks
yields a nice size decrease for the object file.
Size before the patch:
text data bss dec hex filename
4578 240 1032 5850 16da arch/x86/kernel/microcode_intel.o
Size after the patch:
text data bss dec hex filename
4489 240 984 5713 1651 arch/x86/kernel/microcode_intel.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <alpine.LNX.2.00.1012251946100.10759@swampdragon.chaosbits.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We don't need or want MSR usage here, on x86-64.
x86-64 was disabled intentionally in Kconfig, but commit
9272dcc232 changed that.
drivers/ata/pata_cs5536.c:47:1: warning: "rdmsr" redefined
In file included from arch/x86/include/asm/irqflags.h:60,
from include/linux/irqflags.h:15,
from arch/x86/include/asm/system.h:11,
from arch/x86/include/asm/processor.h:17,
from include/linux/prefetch.h:14,
from include/linux/list.h:7,
from include/linux/module.h:9,
from drivers/ata/pata_cs5536.c:33:
arch/x86/include/asm/paravirt.h:146:1: warning: this is the location of the previous definition
drivers/ata/pata_cs5536.c:48:1: warning: "wrmsr" redefined
arch/x86/include/asm/paravirt.h:154:1: warning: this is the location of the previous definition
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
GPEs with corresponding _Lxx/_Exx control methods need to be disabled
during initialization in case they have been enabled by the BIOS, so
that they don't fire up until they are enabled by acpi_update_gpes().
References: https://bugzilla.kernel.org/show_bug.cgi?id=25412
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.
Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch has introduced a regression, whereby a second open of an
soc-camera video device breaks the running capture. This patch fixes this bug
by guaranteeing, that video buffers get initialised only during the first open
of the device node.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi/mpc52xx-spi: fix annotation for remove()-pointer
spi/fsl_espi: fix wrong setting of the address in the command buffer
spi/fsl_espi: change the read behaviour of the SPIRF
of/i2c: Fix request module by alias
powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: issue DIPM enable commands with LPM state updated
libata: no special completion processing for EH commands
pata_mpc52xx: driver needs BMDMA
pata_cs5536: Add support for non-X86_32 platforms
libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
kthread_work: make lockdep happy
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] fix up documentation for change in ->queuecommand to lockless calling
[SCSI] bfa: rename log_level to bfa_log_level
Low level drivers may behave differently depending on the current
link->lpm_policy. During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state. This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.
In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.
Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Move the Kconfig entry to the proper location as needed since
9a7780c9ac (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.
pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Antonio Toma <antonio.toma@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Presently the root node is initialized by way of kzalloc on the parent
data structure, which by chance happens to do the bulk of what an
explicit initialization does with GFP_NOWAIT semantics. This however is
more by luck than by design, and as we ideally want to permit radix node
allocations access to the emergency pools anyways, add in the proper
initializer with the desired mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Or else we can't operate on the right address when the trans length
is greater than 65535.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Malcolm Priestley