Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable GRO by default for performance.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With mtu=9000, mld_newpack() use order-2 GFP_ATOMIC allocations, that
are very unreliable, on machines where PAGE_SIZE=4K
Limit allocated skbs to be at most one page. (order-0 allocations)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch compile tested only.
Convert legacy PM hooks to dev_pm_ops
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.
This patch give the user the ability to control the output slave for
round-robin and active-backup bonding. Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode. Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.
Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag. This will allow reception of unicast traffic on
any of the backup interfaces.
This was tested with IPv4-based filters as well as VLAN-based filters
with good results.
More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: changed parameter name from 'keep_all' to 'all_slaves_active' and
skipped setting slaves to inactive rather than creating a new flag at
Jay's suggestion.
In an effort to suppress duplicate frames on certain bonding modes
(specifically the modes that do not require additional configuration on
the switch or switches connected to the host), code was added in the
generic receive patch in 2.6.16. The current behavior works quite well
for most users, but there are some times it would be nice to restore old
functionality and allow all frames to make their way up the stack.
This patch adds support for a new module option and sysfs file called
'all_slaves_active' that will restore pre-2.6.16 functionality if the
user desires. The default value is '0' and retains existing behavior,
but the user can set it to '1' and allow all frames up if desired.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid an unecessary cache miss by checking if the skb is non-linear
before accessing gso_size/gso_type in skb_warn_if_lro, the same can also be
done to avoid a cache miss on nr_frags if data_len is 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
__pppoe_xmit() in drivers/net/pppoe always returns 1.
When the methods fails (via goto abort), it should return 0 and not 1.
Regards,
Rami Rosen
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- ipv6 msstab: account for ipv6 header size
- ipv4 msstab: add mss for Jumbograms.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
caller: if (!th->rst && !th->syn && th->ack)
callee: if (!th->ack)
make the caller only check for !syn (common for 3whs), and move
the !rst / ack test to the callee.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
both syn_flood_warning functions print a message, but
ipv4 version only prints a warning if CONFIG_SYN_COOKIES=y.
Make the v4 one behave like the v6 one.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its better to make a route lookup in appropriate namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe a moderate SYN flood attack can corrupt RFS flow table
(rps_sock_flow_table), making RPS/RFS much less effective.
Even in a normal situation, server handling short lived sessions suffer
from bad steering for the first data packet of a session, if another SYN
packet is received for another session.
We do following action in tcp_v4_rcv() :
sock_rps_save_rxhash(sk, skb->rxhash);
We should _not_ do this if sk is a LISTEN socket, as about each
packet received on a LISTEN socket has a different rxhash than
previous one.
-> RPS_NO_CPU markers are spread all over rps_sock_flow_table.
Also, it makes sense to protect sk->rxhash field changes with socket
lock (We currently can change it even if user thread owns the lock
and might use rxhash)
This patch moves sock_rps_save_rxhash() to a sock locked section,
and only for non LISTEN sockets.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in multilink fragment size calculation introduced by
commit 9c705260fe
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
syncookies default to on since
e994b7c901
(tcp: Don't make syn cookies initial setting depend on CONFIG_SYSCTL).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only check pfc bits in hang logic if PFC is enabled. Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm triggers a warning if dst_pop() drops a refcount
on a noref dst. This patch changes dst_pop() to
skb_dst_pop(). skb_dst_pop() drops the refcnt only
on a refcounted dst. Also we don't clone the child
dst_entry, so it is not refcounted and we can use
skb_dst_set_noref() in xfrm_output_one().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code was placed incorrectly inside a block of code marked
with CONFIG_INET directive. Fix by moving it outside.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is alternative to a previous patch submitted by Joe Perches.
Create common macros e_<level> and e_dev_<level> that use netdev_<level> and
dev_<level> similar to e1000e.
Redefined pr_fmt for driver messages.
Use %pM to display MAC address.
Aligned text to better match the new format.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops in arp_fwd_proxy()
Avoid two atomic ops in arp_process()
Valid optims since arp_rcv() is run under rcu_read_lock()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on output device refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
access skb->data safely
we should use skb_header_pointer() and skb_store_bits() to access skb->data to
handle small or non-linear skbs.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/sched/act_pedit.c | 24 ++++++++++++++----------
1 file changed, 14 insertions(+), 10 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This exposes the port number to userland through sysfs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source. Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_from_user() returns the number of bytes remaining but we should
return -EFAULT here. The error code gets returned to the user. Both
old_capi_manufacturer() and capi20_manufacturer() had other places
that already returned -EFAULT so this won't break anything.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise negate is intended here. With the logical negate the
condition is always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup patch.
Use new __packed annotation in net/ and include/
(except netfilter)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5c7fffd0e3 ("drivers/net/mac8390.c: Remove
useless memcpy casting") removed too many casts, introducing the following
warnings:
| drivers/net/mac8390.c:248: warning: passing argument 1 of '__builtin_memcpy' makes pointer from integer without a cast
| drivers/net/mac8390.c:253: warning: passing argument 1 of 'word_memcpy_tocard' makes pointer from integer without a cast
| drivers/net/mac8390.c:255: warning: passing argument 2 of 'word_memcpy_fromcard' makes pointer from integer without a cast
Instead of just readding the casts,
- move all casts inside word_memcpy_{to,from}card(),
- replace an incorrect memcpy() by memcpy_toio(),
- add memcmp_withio() as a wrapper around memcmp(),
- replace an incorrect memcpy_toio() by memcpy_fromio().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_CHELSIO_T1_COUGAR cannot be set (it appears nowhere in any
Kconfig files), and the code it protects could never build (cspi.h was
never added to the kernel tree). Therefore it's pretty safe to remove
all vestiges of this dead code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on struct in_device refcount per incoming packet,
if slow path taken, (or route cache disabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Lameter mentioned that packets could be dropped in input path
because of rp_filter settings, without any SNMP counter being
incremented. System administrator can have a hard time to track the
problem.
This patch introduces a new counter, LINUX_MIB_IPRPFILTER, incremented
each time we drop a packet because Reverse Path Filter triggers.
(We receive an IPv4 datagram on a given interface, and find the route to
send an answer would use another interface)
netstat -s | grep IPReversePathFilter
IPReversePathFilter: 21714
Reported-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it's possible to update the DNS record for $HOST_NAME with
ip=::::$HOST_NAME::dhcp
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use skb_header_pointer() to dereference data safely
the original skb->data dereference isn't safe, as there isn't any skb->len or
skb_is_nonlinear() check. skb_header_pointer() is used instead in this patch.
And when the skb isn't long enough, we terminate the function u32_classify()
immediately with -1.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For large values of rtt, 2^rho operation may overflow u32. Clamp down the increment to 2^16.
Signed-off-by: Daniele Lacamera <root@danielinux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
What this patch does is it removes two receive frame hooks (for bridge and for
macvlan) from __netif_receive_skb. These are replaced them with a single
hook for both. It only supports one hook per device because it makes no
sense to do bridging and macvlan on the same device.
Then a network driver (of virtual netdev like macvlan or bridge) can register
an rx_handler for needed net device.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are more than a dozen occurrences of following code in the
IPv6 stack:
if (opt && opt->srcrt) {
struct rt0_hdr *rt0 = (struct rt0_hdr *) opt->srcrt;
ipv6_addr_copy(&final, &fl.fl6_dst);
ipv6_addr_copy(&fl.fl6_dst, rt0->addr);
final_p = &final;
}
Replace those with a helper. Note that the helper overrides final_p
in all cases. This is ok as final_p was previously initialized to
NULL when declared.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log error conditions using KERN_ERR priority.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally dhclient can be configured to send the "host-name" option
in DHCP requests to update the client's DNS record. However for an
NFSROOT system, dhclient shall never be called (which may change the
IP addr and therefore lose your root NFS mount connection).
So enable updating the DNS record with kernel parameter
ip=::::$HOST_NAME::dhcp
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
