The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an orig_dgid attribute in sysfs for SRP scsi_hosts, so that
userspace can tell what the original dgid value written to the
add_target file was, even if the connection is redirected to a
different port while connecting.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB CM spec allows the use of a single connection in both
active->passive and passive->active directions. The current Linux
code uses one connection for both directions, but if another node only
uses one connection for both directions, we oops when we try to look
up the passive connection. Fix by checking that qp_context is
non-NULL before dereferencing it.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix TERMINATE layer, type, and ecode values based on
conformance testing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If skb allocation fails when we start the device, we call
ipoib_cm_dev_stop() even though ipoib_cm_dev_open() did not run to
completion, so we pass an invalid pointer to ib_destroy_cm_id and get
an oops.
Fix by clearing cm.id on error, and testing it in cm_dev_stop().
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=561>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped. Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue. As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.
Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the problem reported by Bernd Schubert <bs@q-leap.de>
with kernel debug options enabled:
BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
This was caused by using spin_lock_irq()/spin_unlock_irq() from
interrupt context. Fix all the places that might be called from
interrupts to use spin_lock_irqsave()/spin_unlock_irqrestore().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just found a hole in my last patch. It was reported to me that shortly after we
integrated this patch. The report was of an oops that took place inside of
netif_rx when using the sis900 driver. Looking at my origional patch I noted
that there was a spot between the new skb_alloc and the refill_rx_ring label
where skb got reassigned to the pointer currently held in the rx_ring for the
purposes of receiveing the frame. The result of this is however that the buffer
that gets passed to netif_rx (if it is called), then gets placed right back into
the rx_ring. So if you receive frames fast enough the skb being processed by
the network stack can get corrupted. The reporter is testing out the fix I've
written for this below (I'm not near my hardware at the moment to test myself),
but I wanted to post it for review ASAP. I'll post test results when I hear
them, but I think this is a pretty straightforward fix. It just uses a separate
pointer to do the rx operation, so that we don't improperly reassign the pointer
that we use to refill the rx ring.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify pegasus carrier detection; rely only on the periodic MII
polling. Reverts pieces of c43c49bd61.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.infradead.org/mtd-2.6: (46 commits)
[MTD] [MAPS] drivers/mtd/maps/ck804xrom.c: convert pci_module_init()
[MTD] [NAND] CM-x270 MTD driver
[MTD] [NAND] Wrong calculation of page number in nand_block_bad()
[MTD] [MAPS] fix plat-ram printk format
[JFFS2] Fix compr_rubin.c build after include file elimination.
[JFFS2] Handle inodes with only a single metadata node with non-zero isize
[JFFS2] Tidy up licensing/copyright boilerplate.
[MTD] [OneNAND] Exit loop only when column start with 0
[MTD] [OneNAND] Fix access the past of the real oobfree array
[MTD] [OneNAND] Update Samsung OneNAND official URL
[JFFS2] Better fix for all-zero node headers
[JFFS2] Improve read_inode memory usage, v2.
[JFFS2] Improve failure mode if inode checking leaves unchecked space.
[JFFS2] Fix cross-endian build.
[MTD] Finish conversion mtd_blkdevs to use the kthread API
[JFFS2] Obsolete dirent nodes immediately on unlink, where possible.
Use menuconfig objects: MTD
[MTD] mtd_blkdevs: Convert to use the kthread API
[MTD] Fix fwh_lock locking
[JFFS2] Speed up mount for directly-mapped NOR flash
...
This patch converts the pci_module_init() usage to pci_register_driver().
It's currently #if 0'ed, but still not a bad idea to change it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix miscellaneous networking compilation errors.
(*) Export ktime_add_ns() for modules.
(*) wext_proc_init() should have an ANSI declaration.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes for various arch compilation problems:
(*) Missing module exports.
(*) Variable name collision when rxkad and af_rxrpc both built in
(rxrpc_debug).
(*) Large constant representation problem (AFS_UUID_TO_UNIX_TIME).
(*) Configuration dependencies.
(*) printk() format warnings.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the wakeup transitions after a VLocation record update completes
one way or another. This builds on Dave Miller's partial fix.
Also move wakeups outside the spinlocked sections.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts eefa390628
The simplification made in that change works with the assumption that
the 'offset' parameter to these functions is always positive or zero,
which is not true. It can be and often is negative in order to access
SKB header values in front of skb->data.
Signed-off-by: David S. Miller <davem@davemloft.net>
irqreturn.h for irqreturn_t and dma_addr_t being u128 warnings ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides MTD support for NAND flash devices on CM-x270 modules.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (78 commits)
USB: update MAINAINERS and CREDITS for Freescale USB driver
USB: update gadget files for fsl_usb2_udc driver
USB: add Freescale high-speed USB SOC device controller driver
USB: quirk for broken suspend of IT8152F/G
USB: iowarrior.c: timeouts too small in usb_control_msg calls
USB: dell device id for option.c
USB: Remove Huawei unusual_devs entry
USB: CP2101 New Device IDs
USB: add picdem device to ldusb
usbfs micro optimitation
USB: remove ancient/broken CRIS hcd
usb ethernet gadget, workaround network stack API glitch
USB: add "busnum" attribute for USB devices
USB: cxacru: ADSL state management
usbatm: Detect usb device shutdown and ignore failed urbs
USB: Remove duplicate define of OHCI_QUIRK_ZFMICRO
USB: BandRich BandLuxe HSDPA Data Card Driver
USB gadget rndis: fix struct rndis_packet_msg_type unaligned bug
USB Elan FTDI: check for driver registration status
USB: sierra: add more checks on shutdown
...
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (184 commits)
V4L/DVB (5563): Radio-maestro.c Replace radio_ioctl to use video_ioctl2
V4L/DVB (5562): Radio-gemtek-pci.c Replace gemtek_pci_ioctl to use video_ioctl2
V4L/DVB (5560): Ivtv: fix incorrect bitwise-and for command flags.
V4L/DVB (5558): Opera: use 7-bit i2c addresses
V4L/DVB (5557): Cafe_ccic: check return value of pci_enable_device
V4L/DVB (5556): Radio-gemtek.c Replace gemtek_ioctl to use video_ioctl2
V4L/DVB (5555): Radio-aimslab.c Replace rt_ioctl to use video_ioctl2
V4L/DVB (5554): Fix: vidioc_g_parm were not zeroing the memory
V4L/DVB (5553): Replace typhoon_do_ioctl to use video_ioctl2
V4L/DVB (5552): Plan-b: Switch to refcounting PCI API
V4L/DVB (5551): Plan-b: header change
V4L/DVB (5550): Radio-sf16fmi.c Replace fmi_do_ioctl to use video_ioctl2
V4L/DVB (5549): Radio-sf16fmr2.c Replace fmr2_do_ioctl to use video_ioctl2
V4L/DVB (5548): Fix v4l2 buffer to the length
V4L/DVB (5547): Add ENUM_FRAMESIZES and ENUM_FRAMEINTERVALS ioctls
V4L/DVB (5546): Radio-terratec.c Replace tt_do_ioctl to use video_ioctl2
V4L/DVB (5545): Saa7146: Release capture buffers on device close
V4L/DVB (5544): Budget-av: Make inversion setting configurable, add KNC ONE V1.0 card
V4L/DVB (5543): Tda10023: Add support for frontend TDA10023
V4L/DVB (5542): Budget-av: Remove polarity switching of the clock for DVB-C
...
Add MAINAINERS and CREDITS entry for Freescale Highspeed USB device
driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update gadget_chip.c, ether.c for newly added Freescale Highspeed USB
device driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freescale high-speed USB SOC can be found on some Freescale processors
among different architectures. It supports both host and device functions.
This driver adds its device support for Linux USB Gadget layer.
It is tested on MPC8349 and MPC8313, but should work on other platforms
with minor tweaks. The driver passed USBCV 1.3 compliance tests. Note
that this driver doesn't yet include OTG support.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jiang Bo <tanya.jiang@freescale.com>
Signed-off-by: Bruce Schmid <duck@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch which adds my device to the list.
This patch enables the broken suspend quirk for the PCI OHCI controller
present in the IT8152F/G RISC-to-PCI Companion Chip.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver uses usb_control_msg() for exchanging data with the device.
When the driver lived freeley _outside_ the kernel tree (pre 2.6.21) the
timeouts for these calls where set to 5*HZ for reading, 1HZ for writing.
(These timeouts seemed to work fine for all users of the driver, at
least nobody complained in the last 2 years.
The current code (2.6.21-rc5) removed the 'HZ' from the timeouts and
left the driver with 5 jiffies for reading and 1 jiffy for writing. My
new machine is fast, but not that fast.
The patch also removes a useless debug statement, which was left over
from testing a broken firmware version
From: Eberhard Fahle <e.fahle@wayoda.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Per the Rui Santos and the hardware manufacturers, this actually inhibits
useful parts of the hardware. The correct way to use this hardware is with the
software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers
are also planning on including Linux drivers/material in future revisions.
CC: Rui Santos <rsantos@grupopie.com>
CC: <johann.wilhelm@student.tugraz.at>
CC: <zihan@huawei.com>
CC: <wanganyu1983@huawei.com>
CC: <dingjianjian@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.
I'm told Axis has a new driver, and will be submitting it soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another workaround for the glitch in the network layer, whereby one call
ignores the (otherwise kernel-wide) convention that free() calls should
not oops when passed nulls. This code already handles that API glitch in
most other paths.
From: Erik Hovland <erik@hovland.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as903) adds a "busnum" sysfs attribute for USB devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device has commands to start/stop the ADSL function, so this adds a
sysfs attribute to allow it to be started/stopped/restarted. It also stops
polling the device for status when the ADSL function is disabled.
There are no problems with sending multiple start or stop commands, even
with a fast loop of them the device still works. There is no need to
protect the restart process from further user actions while it's waiting
for 1.5s.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect usb device shutdown and ignore failed urbs. This happens when the
driver is unloaded or the device is unplugged.
I'm not sure what other urb statuses should be ignored, and the warning
message doesn't need to be shown when the module is unloaded or the device
is removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate define of OHCI_QUIRK_ZFMICRO from ftdi-elan.c, its already
defined in drivers/ush/host/ohci.c
Signed-off-by: "S.Caglar Onur" <caglar@pardus.org.tr>
Cc: <tony.olech@elandigitalsystems.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the detection for the BandRich BandLuxe C100/C100S/C120 HSDPA Data
Card. With the vendor and product IDs are set properly, the data card can
be detected and works fine.
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
skb_push function may return a pointer which is not aligned as required
by struct rndis_packet_msg_type. Using attribute trick to fix this bug.
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland Dreier