Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The use of S3C2410_GP[A-Z]x_INP and S3C2410_GP[A-Z]x_OUTP are
very rare and are taking up large amounts of space in the
regs-gpio.h header.
The GPIO layer has had generic input and out defines called
S3C2410_GPIO_INPUT and S3C2410_GPIO_OUTPUT for a while which work
for all S3C24XX GPIOs.
Do the following replacements:
S3C2410_GP[A-Z][0-9]*_\OUTP => S3C2410_GPIO_OUTPUT
S3C2410_GP[A-Z][0-9]*_\INP => /S3C2410_GPIO_INPUT
S3C2410_GPA[0-9]*_OUT => S3C2410_GPIO_OUTPUT
to remove any usages of these and prepare the header for
the removal of these.
The following command was used to acheive this:
find . -type f -writable ! -name regs-gpio.h ! -name "*~" | xargs sed -i~ -e 's/S3C2410_GP[A-Z][0-9]*_\OUTP/S3C2410_GPIO_OUTPUT/g' -e 's/S3C2410_GP[A-Z][0-9]*_\INP/S3C2410_GPIO_INPUT/g' -e 's/S3C2410_GPA[0-9]*_OUT/S3C2410_GPIO_OUTPUT/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the s3c2410_gpio_irq2pin() function as it is not being
used in any in kernel driver and the function is probably not
being used anywhere else.
This is also part of the effort to remove any of the s3c24xx gpio
specific code that cannot be recreated by using the gpiolib
framework now in the kernel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add missing DMA controller block clocks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add detection support for the S3C6400 SoC which has it's
id register in a different place to the S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.
The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.
The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.
This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for saving the state of the IRQ registers over suspend.
This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.
The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.
Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add an s3c64xx_sysclass and device for items that currently
want to bind to any s3c64xx processor. The first user of this
will be parts of the s3c64xx suspend support which need to
save device state over suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.
Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a simple debug message on saving the UART state and add a per-arch
pre-restore function to be used by the s3c64xx restore code to ensure
the UARTs control registers do not go through any illegal state changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add USB OHCI host capability to the SMDK6410 for either USB OtG or
a single/double USB host port.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This allows the S3C CPUfreq driver to do DVFS.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A&W6410 board uses Samsung S3C6410 SoC and it is registered with 2183.
Framebuffer and ethernet devices are supported currently.
Unnecessary header file is removed.
Fix to use __raw_writel() and __raw_readl() for accessing mapped address.
Thank you for your comments.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since no consumers are currently configured for the SMDK6410 mark all
the supplies on the board as being always_on, ensuring interoperability
with future regulator API changes to disable unused regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Using an active high IRQ ensures that the WM8350 interrupt handling
does not spin when used with a SMDK6410 which has not had R20 removed
and R21 fitted to connect EINT12 to the PMIC module rather thant the
fixed regulators on the CPU module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a basic support for NCP board based on s3c6410.
Only enables the serial. also remove empty i2c device.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SMDK6410 supports pluggable PMIC boards. One such board is the
Wolfson Microelectronics 1190-EV1 for the WM8350 PMICs. This patch
introduces initial support for this module. Further patches will
add additional integration with the system as support for the
S3C6410 and other devices on the system improves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure that the LCD output type is RGB and that
the modem interface is not bypassing the LCD
block. This ensures the LCD interface output
gets to the pins in the correct format.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Fix min function comparison warning
ecryptfs: fix printk format warning
A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two fixes for DViCO FusionHDTV DVB-T Dual Express:
* Reset correct tuner when reinitializing xc3028.
* Disable the I2C gate control to avoid locking up the I2C bus.
Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set_modeready flag must be set before command sent to USB in
s2255_write_config.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Return actual error values as returned by the i2c subsystem, rather
than 0 or 1.
* If the registration of the second bus fails, unregister the first one
before exiting, otherwise we are leaking resources.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.
The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I lowered the kfree(t) down a couple lines and removed the superflous
"t->vdev = NULL;"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I moved the kfree() down a couple lines. t->vdev is going to be in freed
memory so there is no point setting it to NULL. I added a kfree(t) on a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
selecting ALSA module breaks if !SND. Just remove select.
While here, let's fix the whitespacing at the Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A late v4l2_subdev framework change accidentally sent the audio input
routing value to the external multiplexer, instead of the muxer input routing
value to the external multiplexer. This change corrects that error.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
e100: do not go D3 in shutdown unless system is powering off
netfilter: revised locking for x_tables
Bluetooth: Fix connection establishment with low security requirement
Bluetooth: Add different pairing timeout for Legacy Pairing
Bluetooth: Ensure that HCI sysfs add/del is preempt safe
net: Avoid extra wakeups of threads blocked in wait_for_packet()
net: Fix typo in net_device_ops description.
ipv4: Limit size of route cache hash table
Add reference to CAPI 2.0 standard
Documentation/isdn/INTERFACE.CAPI
update Documentation/isdn/00-INDEX
ixgbe: Fix WoL functionality for 82599 KX4 devices
veth: prevent oops caused by netdev destructor
xfrm: wrong hash value for temporary SA
forcedeth: tx timeout fix
net: Fix LL_MAX_HEADER for CONFIG_TR_MODULE
mlx4_en: Handle page allocation failure during receive
mlx4_en: Fix cleanup flow on cq activation
vlan: update vlan carrier state for admin up/down
netfilter: xt_recent: fix stack overread in compat code
...
After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.
This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Dooks