This patch defines PCIe ring buffer array pointer as void instead
of mwifiex_pcie_buf_desc. This will enable us to use same pointers
for ring operations instead of new structures if buffer descriptor
structure changes.
Also split out event buffer descriptor structure from struct
mwifiex_pcie_buf_desc. For PCIe8766 TX/RX buffer descriptor is
same as evevt buffer descriptor. Newer chips could use different
TX/RX buffer descriptor while event descriptor remains the same.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch separates PCIe ring initialization from ring creation
routines. This modularizes ring creation(TXBD, RXBD and event
rings) functions.
Readability has been improved while moving the code around.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for storing PCIe device specific data
into driver_data structure of pci_device_id. When a device with
known device_id is probed, we use this driver_data to populate
card specific structres in driver.
This enables to remove device specific defines for scratch
registers, firmware name, FW download block size, etc. from
source code.
This will make addition of support for new chipsets a lot easier.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On joining an existing IBSS network, beaconing has to start
only after a TSF sync has happened by receiving a beacon from
the BSS. In creator mode, beaconing can start immediately after
a HW reset has been done.
Now that mac80211 notifies the driver of the mode type (creator/joiner)
via ieee80211_bss_conf->ibss_creator, make use of it to properly setup
the HW beacon timers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a few places where the station's HT capabilities
should be checked instead of ATH9K_HW_CAP_HT, which is a global
feature for the driver. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PtZa
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MEI bus API changed according to the latest comments from the char-misc
maintainers, and this patch fixes the microread mei physical layer code
according to those changes:
We pass the MEI id back to the probe routine, and the mei_driver takes a
table of MEI ids instead of one static id.
Also, mei_bus_driver got renamed to mei_driver, mei_bus_client to
mei_device, and mei_bus_set/get_clientdata to mei_set/get_clientdata.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A new model of the RTL8188CUS has appeared.
Reported-and-tested-by: Thomas Rosenkrantz <tom.rosary@googlemail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch off-channel action frames can be transmitted. This
is needed for p2p when two devices need to find each other while
using different social channels.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently netdev gets created possibly after returning from
add_virtual_intf. This is because add_if is handled asynch. This
is wrong and netdev should be up before returning.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some unused defines and comments. Also use same define
for IE length.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a virtual interface cfg80211 already has taken the
rtnl_lock. So when the netdevice is being registered the
register_netdevice should be used instead of register_netdev.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently there is a sleep after disconnect on del_station. This
timeout is not needed (anymore) and is causing problems with p2p
setup, because remote side disconnects then supplicant will do
del_station and while it waits the 400ms remote side will already
reconnect and that is something supplicant cant handle.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wiphy object holds information about possible netdev
combinations which can be supported. This needs updating for
p2p device. Also p2p device netdev has wrong 80211 iftype.
Limit the change interface support to match the netdev
configuration/combination possibilities.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All interfaces for ifidx is 0 are created ahead and therefor
double registrations for not only bssidx 0, but ifidx 0 should
be ignored in brcfm_add_if.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the stored role in wdev struct to determine AP/GO role. This
simplifies code. Fix stop_ap for GO role.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add module variable with which a p2p0 netdev can be created. This
netdev can be used by wpa-supplicant to configure and set up the
p2p client/GO.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 api change needs to be applied. this change will be squashed
with introducing commit:
commit 68751daec95b07a74b18aa22b2f9c196991dbe81
Author: Hante Meuleman <meuleman@broadcom.com>
Date: Mon Nov 26 12:21:27 2012 +0100
brcmfmac: add support for P2P listen mode.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some rare situations the wpa_supplicant can lock up on a remain
on channel command. Use actual cookies for the remain on channel
related commands and allow for additional remain on channel while
still having one set.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch it is possible to send action frames.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once wpa_supplicant has registered for P2P action frames all received
action frames for the device are passed up to cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this update it is possible to create an P2P go. Handle the
p2p go role in creation and the update beacon from cfg80211. Also
store primary bss in global struct. Needed to map cfg device
back to primary device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of p2p connections update the sta connect setup and
handling routines. Use join iovar and bsscfg commands where
applicable. Handle assoc ind per bsscfg (vif) and generalize
vndr ie setup to support assoc IEs and support all setup types,
e.g. sta, ap and p2p.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask is OR-ed with value in case of deregister. Should
be AND-ed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for changing existing interface into p2p go
interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improve exception handling. Store and removed created vif
in cfg.p2p.bss array. Fix big endian bug. Fix msec jiffies bug.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for scanning on non primary netdev (p2p) and
simplify the p2p scanning preparation.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Deletion of the virtual interface was not fully supported so
adding it now. Tested using p2p_connect command in wpa_supplicant.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver determines the P2P interface address and device
address from the primary mac address. However, the function
used an invalid input. This caused a mac address mismatch
between firmware and driver. This was hidden because the
brcmf_if_add() function corrected the error upon receiving
the IF_ADD event from firmware.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 64-bit target a warning was given when using %d to print
sizeof() value:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.o
brcm80211/brcmfmac/wl_cfg80211.c: In function 'brcmf_alloc_vif':
brcm80211/brcmfmac/wl_cfg80211.c:3884:2: error: format '%d' expects
argument of type 'int', but argument 3 has type 'long unsigned int'
[-Werror=format]
Fixed using %zu instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch a device can be put in p2p listen mode and becomes
visible for other p2p devices (via p2p_find).
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allow the creation of P2P client and group owner
virtual interfaces in the driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First part for P2P support. It is a variation on the existing
scanning functionality and is used to discover peer-to-peer
group owners and/or peer-to-peer devices in listen state.
Tested with wpa_cli/wpa_supplicant v2.0-devel.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Locking host access in trap info processing
is not needed as bus access functions do it on
their own.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure backplane clocks are on while reading crash data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix wrong locking in crash info processing
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When unloading it is possible that drvr is not null, but iflist[0]
is. So check iflist[0] pointer before using it.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon receiving an IF event from the firmware the interface
was created and stored on a list using the interface index.
With upcoming P2P feature the firmware will send a IF event
in which two interfaces have the same interface index. To
uniquely locate them on the list the bss index is now used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can, if invalid argument given, return a negative value. In that
case we would access arrays out-of-bounds and such. Check the value
and yell loudly if that happened as it would be a bug in the
implementation. (Instead of silently corrupting memory.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi
BUGS with a NULL pointer dereference because the per-driver configuration
data is not available. The probe function has been restructured as
suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43236 device showed having an issue connection to an AP without
security when auth_type was set to automatic. For this particular device
a workaround is made by selecting open-system. This problem does not
occur when using wpa_supplicant as it will not use auth type automatic.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added function to obtain chip information for chip specific
code.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the bus interface with chip identifier and revision. This
will be used when certain devices need special handling in the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify code by using single function for converting channel to
chanspec. No need to set 40MHz flags, as they are not needed for
correct working in FW.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up function, removing some unnecessary code and
initialisation.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
