Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(pointer > 0) is deeply weird; (pointer >= 0) is even dumber...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
#include <scatterlist/scatterlist.h>
is an odd thing to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct device doesn't have ->dma; it's in struct expansion_card where
that struct device is embedded into.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the symbol "init_level4_pgt" to the vmcoreinfo data so
that makedumpfile (dump filtering command) supports x86_64 sparsemem
kernel of linux-2.6.24.
makedumpfile creates a small dumpfile by excluding unnecessary pages for
the analysis. It checks attributes in page structures and distinguishes
necessary pages and unnecessary ones. To check them, makedumpfile gets
the vmcoreinfo data which has the minimum debugging information only for
dump filtering.
For older x86_64 kernel (linux-2.6.23 or before), makedumpfile translates
the virtual address of page structure into physical address by subtracting
PAGE_OFFSET from virtual address, but this translation isn't effective for
linux-2.6.24 sparsemem kernel, because its page structures are in virtual
memmap area. makedumpfile should translate their virtual address by 4-levels
paging and it needs the symbol "init_level4_pgt".
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix this warning:
arch/x86/kernel/early-quirks.c:40: warning: nvidia_hpet_check defined but not used
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix !CONFIG_SMP warning:
arch/x86/kernel/acpi/processor.c: In function arch_acpi_processor_init_pdc:
arch/x86/kernel/acpi/processor.c:65: warning: unused variable cpu
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel only ever supports 1 version of the boot protocol
so there is no need to check the boot protocol revision to
see if a feature is supported.
Both x86 and x86_64 support the same boot protocol so we need
to implement the KEEP_SEGMENTS on x86_64 as well. It isn't
just paravirt bootloaders that could use this functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There were two problems. Firstly, someone forgot the struct keyword in
front of cpuinfo_x86, so I take it this wasn't even compile checked.
Secondly, the actual definition has this as a SHARED_ALIGNED, so the
definitions mismatch.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
KVM uses smp_call_function_mask and therefor need smp_ops to be exported.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 6442eea937.
The patch breaks smp_ops and needs to be reverted. The solution to
allow modular build of KVM is to export smp_ops instead.
Pointed-out-by: James Bottomley
<jejb> tglx, so write out 100 times "voyager is a useful architecture" ...
<tglx> yes, Sir
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/mtd-2.6:
[JFFS2] Update MAINTAINERS entry -- the jffs-dev list is dead
[JFFS2] Prevent return of initialised variable in jffs2_init_acl_post()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc_spi: Fix mmc-over-spi regression
mmc: use common byte swap macros
mmc: fix cid and csd byte order
at91_mci: Fix bad reference
Patch 49dce689ad changed the sysfs data
structures for SPI in a way which broke the MMC-over-SPI host driver.
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the sg_init_table out of the timing loops for hash
algorithms so that it doesn't impact on the speed test results.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pid namespace patches changed the semantics of
find_task_by_pid without breaking the compile resulting
in get_net_ns_by_pid doing the wrong thing.
So switch to using the intended find_task_by_vpid.
Combined with Denis' earlier patch to make netlink traffic
fully synchronous the inadvertent race I introduced with
accessing current is actually removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not safe to to place struct pernet_operations in a special section.
We need struct pernet_operations to last until we call unregister_pernet_subsys.
Which doesn't happen until module unload.
So marking struct pernet_operations is a disaster for modules in two ways.
- We discard it before we call the exit method it points to.
- Because I keep struct pernet_operations on a linked list discarding
it for compiled in code removes elements in the middle of a linked
list and does horrible things for linked insert.
So this looks safe assuming __exit_refok is not discarded
for modules.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following compile errors in some configurations:
<-- snip -->
...
CC net/ipv4/esp4.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv4/esp4.c: In function 'esp_output':
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv4/esp4.c:113: error: implicit declaration of function 'sg_init_table'
make[3]: *** [net/ipv4/esp4.o] Error 1
...
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv6/esp6.c: In function 'esp6_output':
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv6/esp6.c:112: error: implicit declaration of function 'sg_init_table'
make[3]: *** [net/ipv6/esp6.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/tcp_ipv6.c: In function 'tcp_v6_rcv':
net/ipv6/tcp_ipv6.c:1736: error: implicit declaration of function
'get_softnet_dma'
net/ipv6/tcp_ipv6.c:1736: warning: assignment makes pointer from integer
without a cast
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
x86 setup: sizeof() is unsigned, unbreak comparisons
x86 setup: handle boot loaders which set up the stack incorrectly
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
x86: kill the old i386 and x86_64 directories
x86: move i386 and x86_64 Kconfig files to x86 directory
kconfig: small code refactoring in kconfig Makefile
x86: unification of i386 and x86_64 Kconfig.debug
x86: move defconfig files for i386 and x86_64 to x86
x86: move i386 and x86_64 Makefiles to arch/x86
From the report by Nick Warne.
Tested-by: Nick Warne <nick@ukfsn.org>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* We shouldn't bother with dev->current_state, the PCI API functions we
call manage this for us (and do a far better job at it too).
* Remove pci_set_power_state(dev, PCI_D0) call in resume, as
pci_enable_device() does the same thing.
* Check pci_enable_device() return value. If it failed, fail
the entire resume and avoid programming timings into the [potentially
dead/asleep] chip.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
Cc: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that hpt366 host driver is also affected by the same issue:
> drivers/ide/pci/hpt366.c:1428: error: hpt366_chipsets causes a section type
> conflict
This patch workarounds the problem by making static struct hpt_info instances
const. Now all __devinitdata data in hpt366 host driver are read-only so it
builds again (driver's .init.data section gets marked as READONLY).
While at it:
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently.
This patch workarounds the problem by removing __devinitdata tag from 'primary'
variable (which makes 'primary' to be moved from .init.data to .bss section).
Now all __devinitdata data in cy82c693 host driver are read-only so it builds
again (driver's .init.data section gets marked as READONLY).
While at it:
* Move 'primary' variable to its only user, init_iops_cy82c693().
* Bump driver version.
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun Heo