Now that Greg implemented MCFG/_SEG support this shouldn't be needed
anymore
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Optimize the deadlock avoidance check on the global cpuset
semaphore cpuset_sem. Instead of adding a depth counter to the
task struct of each task, rather just two words are enough, one
to store the depth and the other the current cpuset_sem holder.
Thanks to Nikita Danilov for the idea.
Signed-off-by: Paul Jackson <pj@sgi.com>
[ We may want to change this further, but at least it's now
a totally internal decision to the cpusets code ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove w1 comments from crc16.h and move specific constants into
w1_ds2433.c where they are used.
Replace %d with %zd.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
..and only enable them for ia64. The functions are only valid
when the whole system has been totally stopped and no scheduler
activity is ongoing on any CPU, and interrupts are globally
disabled.
In other words, they aren't useful for anything else. So make
sure that nobody can use them by mistake.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ppc64_attention_msg and ppc64_dump_msg are not used so remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the rtas start-cpu token doesnt exist then presume the cpu is already
spinning. If it isnt we will catch it later on when the cpu doesnt
respond.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few xics cleanups:
- Make some things static.
- Be more consistent with error printing - interrupts are unsigned,
error values are signed.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Add PTRACE_GET_DEBUGREG/PTRACE_SET_DEBUGREG. The definition is
as follows:
/*
* Get or set a debug register. The first 16 are DABR registers and the
* second 16 are IABR registers.
*/
#define PTRACE_GET_DEBUGREG 25
#define PTRACE_SET_DEBUGREG 26
DABR == data breakpoint and IABR = instruction breakpoint in IBM
speak. We could split out the IABR into 2 more ptrace calls but I
figured there was no need and 16 DABR registers should be more
than enough (POWER4/POWER5 have one).
- Add 2 new SIGTRAP si_codes: TRAP_HWBKPT and TRAP_BRANCH. I couldnt
find any standards on either of these so I copied what ia64 is
doing. Again this might be better placed in
include/asm-generic/siginfo.h
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Remove the PPC_REG* defines
- Wrap some more stuff with ifdef __KERNEL__
- Add missing PT_TRAP, PT_DAR, PT_DSISR defines
- Add PTRACE_GETEVRREGS/PTRACE_SETEVRREGS, even though we dont use it on
ppc64 we dont want to allocate them for something else.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace get and set methods for VMX/Altivec registers present in the
ppc tree were missing for ppc64. This patch adds the 32-bit and
64-bit methods. Updated with the suggestions from Anton following the lines
of his code snippet.
Added:
- flush_altivec_to_thread calls as suggested by Anton
- piecewise copy of structure to preserve 32-bit vrsave data as per
Anton
(I consolidated the 32 and 64bit versions with 2 helper macros - Anton)
Signed-off-by: Robert C Jennings <rcjenn@austin.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code which gives us the option on ppc64 of instantiating the
PCI tree (the tree of pci_bus and pci_dev structs) from the Open
Firmware device tree rather than by probing PCI configuration space.
The OF device tree has a node for each PCI device and bridge in the
system, with properties that tell us what addresses the firmware has
configured for them and other details.
There are a couple of reasons why this is needed. First, on systems
with a hypervisor, there is a PCI-PCI bridge per slot under the PCI
host bridges. These PCI-PCI bridges have special isolation features
for virtualization. We can't write to their config space, and we are
not supposed to be reading their config space either. The firmware
tells us about the address ranges that they pass in the OF device
tree.
Secondly, on powermacs, the interrupt controller is in a PCI device
that may be behind a PCI-PCI bridge. If we happened to take an
interrupt just at the point when the device or a bridge on the path to
it was disabled for probing, we would crash when we try to access the
interrupt controller.
I have implemented a platform-specific function which is called for
each PCI bridge (host or PCI-PCI) to say whether the code should look
in the device tree or use normal PCI probing for the devices under
that bridge. On pSeries machines we use the device tree if we're
running under a hypervisor, otherwise we use normal probing. On
powermacs we use normal probing for the AGP bridge, since the device
for the AGP bridge itself isn't shown in the device tree (at least on
my G5), and the device tree for everything else.
This has been tested on a dual G5 powermac, a partition on a POWER5
machine (running under the hypervisor), and a legacy iSeries
partition.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update i810fb documentation to describe new features and configuration
changes.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Manuel Lauss <mano@roarinelk.homelinux.net>
He was getting random initial video modes depending on the kernel
configuration. His option line includes 'extvga'.
The i810fb documentation describes the option 'extvga', however the
driver accepts 'ext_vga'. Besides 'extvga' being ignored by i810fb,
it also confuses the option parser of i810fb and assigns 'extvga' to
'mode_option'. This leads to an incorrect video mode at boot time.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If i810fb successfully probed for the EDID, it will disregard the
boot option parameters 'xres' and 'yres'. Fix this regression.
Excellent testing done by Manuel Lauss <mano@roarinelk.homelinux.net>.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create common start code for all 68360 based platforms that are
loaded and run directly from RAM (as opposed to running from
flash/ROM). This replaces the old specific startup code for
each board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow for differences in the SDRAM controller setup and GPIO pin setup
of the 5270/1 and 5274/5 parts. With separate config options for each
now this no longer needs to be board specific.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC ethernet driver of the Freescale 523x processor
family to the FEC header definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move call to get_mm_counter() in update_mem_hiwater() to be
inside the check for tsk->mm being null. Otherwise you can be
following a null pointer here. This patch submitted by
Javier Herrero <jherrero@hvsistemas.es>.
Modify the end check for munmap regions to allow for the
legacy behavior of 0 being valid. Pretty much all current
uClinux system libc malloc's pass in 0 as the end point.
A hard check will fail on these, so change the check so
that if it is non-zero it must be valid otherwise it fails.
A passed in value will always succeed (as it used too).
Also export a few more mm system functions - to be consistent
with the VM code exports.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support the DMA unit of the ColdFire 523x processor family.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should not call mtd_put_device() in the uclinux MTD map driver.
Also consistently use phys/virt fields of maps map_info struct,
instead of mixing it with map_priv_1.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the new Freescale 523x processor family to ColdFire
serial driver. Also set different default baud rate for MOD5272
board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change addr arg to find_next_zero_bit to be a const.
Cleans up compiler warning.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bring arg types for csum_partial_copy and csum_paritial_copy_from_user
prototypes into line with their actual implementation.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create common start code for all 68360 based platforms that are
loaded and run directly from ROM/flash (as opposed to running from
RAM). This replaces the old specific startup code for each board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the cache of the ColdFIre 523x family of processors.
Enable the 528x cache by default now, all final shipping silicon
has the cache bug fixed.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few improvements to the Freescale/ColdFire FEC driver:
. some formatting cleanups
. add support for the FEC device in the ColdFire 523x processor family
. add support for MAC address setting on MOD5272 and M5272C3 boards
. don't re-read the PHY status register many times
. ack status interrupt before reading status register
. move printing init message to after full init (so that the
ethX name is filled out for printing)
Some parts of this patch submitted by Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add configuration support for the FEC ethernet controller in the
Freescale 523x processor family. Also add and option to configure
the second FEC controller on some Freescale processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the special case unwind code that was only used by the old
MCA/INIT handler.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The bulk of the change. Use per cpu MCA/INIT stacks. Change the SAL
to OS state (sos) to be per process. Do all the assembler work on the
MCA/INIT stacks, leaving the original stack alone. Pass per cpu state
data to the C handlers for MCA and INIT, which also means changing the
mca_drv interfaces slightly. Lots of verification on whether the
original stack is usable before converting it to a sleeping process.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reading the INIT record from SAL during the INIT event has proved to be
unreliable, and a source of hangs during INIT processing. The new
MCA/INIT handlers remove the need to get the INIT record from SAL.
Change salinfo.c so mca.c can just flag that a new record is available,
without having to read the record during INIT processing. This patch
can be applied without the new MCA/INIT handlers.
Also clean up some usage of NR_CPUS which should have been using
cpu_online().
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add an extra thread_info flag to indicate the special MCA/INIT stacks.
Mainly for debuggers.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Scheduler hooks to see/change which process is deemed to be on a cpu.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cannot build MIPS now.
We need to change offset.c to asm-offsets.c
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Al Viro reported that sometimes silentoldconfig failed because
output directory was missing.
So create it unconditionally before executing conf
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Clash due to new delete_inode behavior (the filesystem now needs to do
the truncate_inode_pages() call itself).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen