i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.
IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Impact: use new work_on_cpu function to reduce stack usage
Replace the saving of current->cpus_allowed and set_cpus_allowed_ptr() with
a work_on_cpu function for drv_read() and drv_write().
Basically converts do_drv_{read,write} into "work_on_cpu" functions that
are now called by drv_read and drv_write.
Note: This patch basically reverts 50c668d6 which reverted 7503bfba, now
that the work_on_cpu() function is more stable.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Dieter Ries <clip2@gmx.de>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <cpufreq@vger.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is only one clock board, so use -1 as the 'id' so we get just
the base name as the LED device name string.
There are multiple FHC boards potentially in a system so use the board
number as the 'id' value for that case.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only exclusive definitions are SSCR0_SCR and SSCR0_SerClkDiv(), loosen
that exclusive #ifdef .. #else .. #endif to allow other definitions to be
visible when slected multiple processors. This helps to pass the building
of pxa-ssp.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
After commit 8c3abc7d90
("[ARM] pxa: convert to clkdev and match clocks by struct device where possible")
get_clk in pxa3xx_nand fails with -ENOENT.
Apparently, clk_get in pxamci will also fail for MCI2 on PXA310.
The 'clk_find' and therefore 'clk_get' require driver to supply
both 'dev_id' and 'con_id' if they are not NULL in the 'strcut clk_lookup',
but neither pxa3xx_nand nor pxamci supply 'con_id'.
This patch sets 'con_id' to NULL in NAND clock and MCI2 clock registration.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The function setup_cpu_local_masks() has been marked __init, in
order to remove the following section mismatch messages:
WARNING: vmlinux.o(.text+0x3c2c7): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2d3): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2df): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2eb): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add debug warning
Fire off one message if two apic's discovered with different
apic versions. (this code is only called during CPU init)
The goal of this is to pave the way of the removal of the apic_version[]
array. We dont expect any apic version incompatibilities in the x86
landscape of systems [if so we dont handle them very well and probably
never will handle deep apic version assymetries well], but it's prudent
to have a debug check for one kernel cycle nevertheless.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previously PeeCeeI.o was a library but it
was always pulled in due to insw and friends being exported
(at least for a modular kernel).
But this resulted in modpost failures if there where no in-kernel
users because then insw & friends were not linked in.
Fix this by including PeeCeeI.o in the kernel unconditionally.
The only drawback for this solution is that a nonmodular kernel
will always include insw & friends no matter if they are in use or not.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meelis reported that on his box /proc/cpuinfo started
to reported "Unknow CPU" and the same did the boot messages.
It was a stupid bug I introduced when merging
cpu.c for 32 and 64 bit.
The code did an array reference where it had to search
for the right index.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster
depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y.
This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y
and CONFIG_FREEZER=n.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
Debugging and original patch from Nick Piggin <npiggin@suse.de>
The early fixmap pmd entry inserted at the very top of the KVA is causing the
subsequent fixmap mapping code to not provide physically linear pte pages over
the kmap atomic portion of the fixmap (which relies on said property to
calculate pte addresses).
This has caused weird boot failures in kmap_atomic much later in the boot
process (initial userspace faults) on a 32-bit PAE system with a larger number
of CPUs (smaller CPU counts tend not to run over into the next page so don't
show up the problem).
Solve this by attempting to clear out the page table, and copy any of its
entries to the new one. Also, add a bug if a nonlinear condition is encountered
and can't be resolved, which might save some hours of debugging if this fragile
scheme ever breaks again...
Once we have such logic, we can also use it to eliminate the early ioremap
trickery around the page table setup for the fixmap area. This also fixes
potential issues with FIX_* entries sharing the leaf page table with the early
ioremap ones getting discarded by early_ioremap_clear() and not restored by
early_ioremap_reset(). It at once eliminates the temporary (and configuration,
namely NR_CPUS, dependent) unavailability of early fixed mappings during the
time the fixmap area page tables get constructed.
Finally, also replace the hard coded calculation of the initial table space
needed for the fixmap area with a proper one, allowing kernels configured for
large CPU counts to actually boot.
Based-on: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge header files for m68k and m68knommu to the single location:
arch/m68k/include/asm
The majority of this patch was the result of the
script that is included in the changelog below.
The script was originally written by Arnd Bergman and
exten by me to cover a few more files.
When the header files differed the script uses the following:
The original m68k file is named <file>_mm.h [mm for memory manager]
The m68knommu file is named <file>_no.h [no for no memory manager]
The files uses the following include guard:
This include gaurd works as the m68knommu toolchain set
the __uClinux__ symbol - so this should work in userspace too.
Merging the header files for m68k and m68knommu exposes the
(unexpected?) ABI differences thus it is easier to actually
identify these and thus to fix them.
The commit has been build tested with both a m68k and
a m68knommu toolchain - with success.
The commit has also been tested with "make headers_check"
and this patch fixes make headers_check for m68knommu.
The script used:
TARGET=arch/m68k/include/asm
SOURCE=arch/m68knommu/include/asm
INCLUDE="cachectl.h errno.h fcntl.h hwtest.h ioctls.h ipcbuf.h \
linkage.h math-emu.h md.h mman.h movs.h msgbuf.h openprom.h \
oplib.h poll.h posix_types.h resource.h rtc.h sembuf.h shmbuf.h \
shm.h shmparam.h socket.h sockios.h spinlock.h statfs.h stat.h \
termbits.h termios.h tlb.h types.h user.h"
EQUAL="auxvec.h cputime.h device.h emergency-restart.h futex.h \
ioctl.h irq_regs.h kdebug.h local.h mutex.h percpu.h \
sections.h topology.h"
NOMUUFILES="anchor.h bootstd.h coldfire.h commproc.h dbg.h \
elia.h flat.h m5206sim.h m520xsim.h m523xsim.h m5249sim.h \
m5272sim.h m527xsim.h m528xsim.h m5307sim.h m532xsim.h \
m5407sim.h m68360_enet.h m68360.h m68360_pram.h m68360_quicc.h \
m68360_regs.h MC68328.h MC68332.h MC68EZ328.h MC68VZ328.h \
mcfcache.h mcfdma.h mcfmbus.h mcfne.h mcfpci.h mcfpit.h \
mcfsim.h mcfsmc.h mcftimer.h mcfuart.h mcfwdebug.h \
nettel.h quicc_simple.h smp.h"
FILES="atomic.h bitops.h bootinfo.h bug.h bugs.h byteorder.h cache.h \
cacheflush.h checksum.h current.h delay.h div64.h \
dma-mapping.h dma.h elf.h entry.h fb.h fpu.h hardirq.h hw_irq.h io.h \
irq.h kmap_types.h machdep.h mc146818rtc.h mmu.h mmu_context.h \
module.h page.h page_offset.h param.h pci.h pgalloc.h \
pgtable.h processor.h ptrace.h scatterlist.h segment.h \
setup.h sigcontext.h siginfo.h signal.h string.h system.h swab.h \
thread_info.h timex.h tlbflush.h traps.h uaccess.h ucontext.h \
unaligned.h unistd.h"
mergefile() {
BASE=${1%.h}
git mv ${SOURCE}/$1 ${TARGET}/${BASE}_no.h
git mv ${TARGET}/$1 ${TARGET}/${BASE}_mm.h
cat << EOF > ${TARGET}/$1
EOF
git add ${TARGET}/$1
}
set -e
mkdir -p ${TARGET}
git mv include/asm-m68k/* ${TARGET}
rmdir include/asm-m68k
git rm ${SOURCE}/Kbuild
for F in $INCLUDE $EQUAL; do
git rm ${SOURCE}/$F
done
for F in $NOMUUFILES; do
git mv ${SOURCE}/$F ${TARGET}/$F
done
for F in $FILES ; do
mergefile $F
done
rmdir arch/m68knommu/include/asm
rmdir arch/m68knommu/include
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PAPR says that the property for specifying the number of SLBs should
be called "slb-size". We currently only look for "ibm,slb-size" because
this is what firmware actually presents.
This patch makes us look for the "slb-size" property as well and in
preference to the "ibm,slb-size". This should future proof us if
firmware changes to match PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
The subpage_prot syscall fails on second and subsequent calls for a given
region, because is_hugepage_only_range() is mis-identifying the 4 kB
slices when the process has a 64 kB page size.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes compiler warnings:
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes these compiler warning:
arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.
This removes warnings like this:
arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type
Also, these:
drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Push the dma_addr_t type usage all the way down to where the actual
values are manipulated.
Now that u64 is "unsigned long long", this removes warnings like:
arch/powerpc/platforms/ps3/system-bus.c:532: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
arch/powerpc/platforms/ps3/system-bus.c:649: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also silences this warning:
arch/powerpc/platforms/ps3/setup.c:275: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As it's just a single call to __get_free_page().
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike other alphas, marvel doesn't have real PC-style CMOS clock hardware
- RTC accesses are emulated via PAL calls. Unfortunately, for unknown
reason these calls work only on CPU #0. So current implementation for
arbitrary CPU makes CMOS_READ/WRITE to be executed on CPU #0 via IPI.
However, for obvious reason this doesn't work with standard
get/set_rtc_time() functions, where a bunch of CMOS accesses is done with
disabled interrupts.
Solved by making the IPI calls for entire get/set_rtc_time() functions,
not for individual CMOS accesses. Which is also a lot more effective
performance-wise.
The patch is largely based on the code from Jay Estabrook.
My changes:
- tweak asm-generic/rtc.h by adding a couple of #defines to
avoid a massive code duplication in arch/alpha/include/asm/rtc.h;
- sys_marvel.c: fix get/set_rtc_time() return values (Jay's FIXMEs).
NOTE: this fixes *only* LIB_RTC drivers. Legacy (CONFIG_RTC) driver
wont't work on marvel. Actually I think that we should just disable
CONFIG_RTC on alpha (maybe in 2.6.30?), like most other arches - AFAIK,
all modern distributions use LIB_RTC anyway.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently introduced generic pci_common_swizzle() relies on bus->self
being NULL for the root PCI bus. But on nautilus bus->self points to
the host bridge device, which is necessary as we do a root bus sizing
on this system. As a result, pci_common_swizzle() loops infinitely.
This worked until 2.6.29-rc1 because the alpha-specific swizzle routine
checked for bus->parent == NULL (instead of bus->self).
Fixed by clearing bus->self after bus sizing is done.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
init_srm_irq() deals with irq's #16 and above, but size of irq_desc
array on nautilus and some other system types is 16. So gcc-4.3
complains that "array subscript is above array bounds", even though
this function is never called on those systems.
This adds a check for NR_IRQS <= 16, which effectively optimizes
init_srm_irq() code away on problematic platforms.
Thanks to Daniel Drake <dsd@gentoo.org> for detailed analysis
of the problem.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 58dab916df, which
makes my Nehalem come to a nasty crawling almost-halt. It looks like it
turns off caching of regular kernel RAM, with the understandable
slowdown of a few orders of magnitude as a result.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function uv_wait_completion() spins on reads of a memory-mapped
register, waiting for completion of BAU hardware replies.
It should call "cpu_relax()" between those reads to improve performance
on hyperthreaded configurations.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create a platform specific version of dma_get_required_mask()
for ia64 SN Altix. All SN Altix platforms support 64 bit DMA
addressing regardless of the size of system memory.
Create an ia64 machvec for dma_get_required_mask, with the
SN version unconditionally returning DMA_64BIT_MASK.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CONFIG_SATA_VITESSE=y was not added to generic_defconfig when
sn2_defconfig was removed. SGI Altix systems that use an IO10
base IO card to drive the root device are unable to boot without
the Vitesse controller.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Often the cause of kernel unaligned access warnings is not
obvious from just the ip displayed in the warning. This adds
the option via proc to dump the stack in addition to the warning.
The default is off (just display the 1 line warning). To enable
the stack to be shown: echo 1 > /proc/sys/kernel/unaligned-dump-stack
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
sched_clock() on ia64 is based on ar.itc, so is never
completely synchronized between cpus. On some platforms
(e.g. certain models of SGI Altix) it may be running at
radically different frequencies.
Based on a patch from Dimitri Sivanich which set this
just for SN2 && GENERIC kernels ... it is needed for
all ia64 machines.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes the following errors caused by
79741dd357 which changed
the prototypes of account_steal_time() and account_idle_time().
> CC arch/ia64/xen/time.o
> arch/ia64/xen/time.c: In function 'consider_steal_time':
> arch/ia64/xen/time.c:132: warning: passing argument 1 of 'account_steal_time' makes integer from pointer without a cast
> arch/ia64/xen/time.c:132: error: too many arguments to function 'account_steal_time'
> arch/ia64/xen/time.c:133: warning: passing argument 1 of 'account_steal_time' makes integer from pointer without a cast
> arch/ia64/xen/time.c:133: error: too many arguments to function 'account_steal_time'
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes old platform devices. Alsa should now
be using the ASoC driver. For boards not yet using ASoC,
please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770
to keep things compiling.
Remove references to omap_gpio_switch, and unused h2_nand_dev_ready
function.
This patch is based on an earlier patch by Arun KS.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables writing to McBSP Transmit Configuration Control
Register (XCCR) and Receive Configuration Control Register (RCCR)
for 2430/34xx platforms. It also adds XCCR, RCCR entries in McBSP
register configuration structure and bit definitions for both
registers.
If we enable the writing to CCR registers for 2430/34xx and don't
set the default values (setting 0 as a consequence) in ASoC driver,
the Transmit/Receive DMA mode gets disabled and the the
transmission/reception doesn't happen, ending with a
"write error: Input/Output error" when playing with 'aplay'.
Also define dummy CCR registers for omap1.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding I2C board info is required for tlvaic23 i2c chip driver.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bug in existing code causes synchro control to be set +32 if request
line greater than 63 is used.
Also clean up the function a bit by removing extra parens and
clearing the bits at before write.
Reported by Wenbiao Wang.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are no wakeup registers on 15xx, and suspend_wakeup
does not exist in the struct gpio_bank.
Without this fix we'll get "arch/arm/plat-omap/gpio.c:1792:
error: 'struct gpio_bank' has no member named 'suspend_wakeup'"
as noted by Russell King.
Note that the ifdefs will be cleaned up once the omap gpio
code gets split into omap1 and omap2 specific parts.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove old MMC platform init code accidentally
left behind.
Patches are welcome to the new style MMC init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/83xx: Move mcu_mpc8349emitx driver out of drivers/i2c/chips/
powerpc/83xx: Make serial ports work on MPC8315E-RDB w/ FSL U-Boots
powerpc/e500mc: Doorbells need to be taken w/exceptions disabled
powerpc: Enable PS3 options and QPACE in ppc64_defconfig
powerpc/powermac: Fix occasional SMP boot failure
powerpc/cacheinfo: Rename cache_dir per-cpu variable
hvc_console: Use kzalloc() instead of kmalloc() + memset()
hvc_console: Do not set low_latency when using interrupts
hvc_console: Call free_irq() only if request_irq() was successful
hvc_console: Change an mb() to smp_mb() and add some comments
powerpc: Cleanup from l64 to ll64 change: drivers/net
powerpc: Cleanup from l64 to ll64 change: drivers/char
powerpc: Cleanup from l64 to ll64 change: arch code
powerpc: Change u64/s64 to a long long integer type
powerpc/kexec: Check crash_base for relocatable kernel
powerpc: Make dummy section a valid note header
Xilinx: SPI: updated driver for device tree
drivers/of: Add the of_find_i2c_device_by_node function.
powerpc/xsysace: add compatible string for non-ipcore instance
powerpc/mpc52xx: remove dead code from GPIO driver
...
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust the arch overrides to the new names as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit ad7a953c52.
And commit: ("allow stripping of generated symbols under CONFIG_KALLSYMS_ALL")
9bb482476c
These stripping patches has caused a set of issues:
1) People have reported compatibility issues with binutils due to
lack of support for `--strip-unneeded-symbols' with objcopy 2.15.92.0.2
Reported by: Wenji
2) ccache and distcc no longer works as expeced
Reported by: Ted, Roland, + others
3) The installed modules increased a lot in size
Reported by: Ted, Davej + others
Reported-by: Wenji Huang <wenji.huang@oracle.com>
Reported-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Thierry Vignaud reported:
> http://bugzilla.kernel.org/show_bug.cgi?id=12372
>
> On P4 with an SiS motherboard (video card is a SiS 651)
> X server fails to start with error:
> xf86MapVidMem: Could not mmap framebuffer (0x00000000,0x2000) (Invalid
> argument)
Here X is trying to map first 8KB of memory using /dev/mem. Existing
code treats first 0-4KB of memory as non-RAM and 4KB-8KB as RAM. Recent
code changes don't allow to map memory with different attributes
at the same time.
Fix this by treating the first 1MB legacy region as special and always
track the attribute requests with in this region using linear linked
list (and don't bother if the range is RAM or non-RAM or mixed)
Reported-and-tested-by: Thierry Vignaud <tvignaud@mandriva.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enables the use of syscall wrappers to do proper sign extension
for 64-bit programs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Martin Schwidefsky <schwidefsky@de.ibm.com>
By selecting HAVE_SYSCALL_WRAPPERS architectures can activate
system call wrappers in order to sign extend system call arguments.
All architectures where the ABI defines that the caller of a function
has to perform sign extension probably need this.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Remove __attribute__((weak)) from common code sys_pipe implemantation.
IA64, ALPHA, SUPERH (32bit) and SPARC (32bit) have own implemantations
with the same name. Just rename them.
For sys_pipe2 there is no architecture specific implementation.
Cc: Richard Henderson <rth@twiddle.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
sparc_ksyms_64.c includes asm/spinlock.h directly, which is
a no-no.
Even better, none of these exports are even necessary. All
of these functions are inlines.
Reported by Meelis Roos and Alexander Beregalov.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is used to help Jean Delvare to get rid of drivers/i2c/chips/
directory. The new location suggested by Kumar Gala: as the driver is
83xx specific it's placed into arch/powerpc/platforms/83xx/.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We use Doorbell interrupts for IPIs and thus we need to make sure we aren't
interrupted in the process of processing the IPI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Dave Liu <daveliu@freescale.com>
* 'x86-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 PAT: remove CPA WARN_ON for zero pte
x86 PAT: return compatible mapping to remap_pfn_range callers
x86 PAT: change track_pfn_vma_new to take pgprot_t pointer param
x86 PAT: consolidate old memtype new memtype check into a function
x86 PAT: remove PFNMAP type on track_pfn_vma_new() error
* master.kernel.org:/home/rmk/linux-2.6-arm:
TWL4030: fix clk API usage
[ARM] 5364/1: allow flush_ioremap_region() to be used from modules
[ARM] w90x900: fix build errors and warnings
[ARM] i.MX add missing include
[ARM] i.MX: fix breakage from commit 278892736e
[ARM] i.MX: remove LCDC controller register definitions from imx-regs.h
Impact: reduce scope of debug check - avoid warnings
The logic to find whether identity map exists or not using
high_memory or max_low_pfn_mapped/max_pfn_mapped are not complete
as the memory withing the range may not be mapped if there is a
unusable hole in e820.
Specifically, on my test system I started seeing these warnings with
tools like hwinfo, acpidump trying to map ACPI region.
[ 27.400018] ------------[ cut here ]------------
[ 27.400344] WARNING: at /home/venkip/src/linus/linux-2.6/arch/x86/mm/pageattr.c:560 __change_page_attr_set_clr+0xf3/0x8b8()
[ 27.400821] Hardware name: X7DB8
[ 27.401070] CPA: called for zero pte. vaddr = ffff8800cff6a000 cpa->vaddr = ffff8800cff6a000
[ 27.401569] Modules linked in:
[ 27.401882] Pid: 4913, comm: dmidecode Not tainted 2.6.28-05716-gfe0bdec #586
[ 27.402141] Call Trace:
[ 27.402488] [<ffffffff80237c21>] warn_slowpath+0xd3/0x10f
[ 27.402749] [<ffffffff80274ade>] ? find_get_page+0xb3/0xc9
[ 27.403028] [<ffffffff80274a2b>] ? find_get_page+0x0/0xc9
[ 27.403333] [<ffffffff80226425>] __change_page_attr_set_clr+0xf3/0x8b8
[ 27.403628] [<ffffffff8028ec99>] ? __purge_vmap_area_lazy+0x192/0x1a1
[ 27.403883] [<ffffffff8028eb52>] ? __purge_vmap_area_lazy+0x4b/0x1a1
[ 27.404172] [<ffffffff80290268>] ? vm_unmap_aliases+0x1ab/0x1bb
[ 27.404512] [<ffffffff80290105>] ? vm_unmap_aliases+0x48/0x1bb
[ 27.404766] [<ffffffff80226d28>] change_page_attr_set_clr+0x13e/0x2e6
[ 27.405026] [<ffffffff80698fa7>] ? _spin_unlock+0x26/0x2a
[ 27.405292] [<ffffffff80227e6a>] ? reserve_memtype+0x19b/0x4e3
[ 27.405590] [<ffffffff80226ffd>] _set_memory_wb+0x22/0x24
[ 27.405844] [<ffffffff80225d28>] ioremap_change_attr+0x26/0x28
[ 27.406097] [<ffffffff80228355>] reserve_pfn_range+0x1a3/0x235
[ 27.406427] [<ffffffff80228430>] track_pfn_vma_new+0x49/0xb3
[ 27.406686] [<ffffffff80286c46>] remap_pfn_range+0x94/0x32c
[ 27.406940] [<ffffffff8022878d>] ? phys_mem_access_prot_allowed+0xb5/0x1a8
[ 27.407209] [<ffffffff803e9bf4>] mmap_mem+0x75/0x9d
[ 27.407523] [<ffffffff8028b3b4>] mmap_region+0x2cf/0x53e
[ 27.407776] [<ffffffff8028b8cc>] do_mmap_pgoff+0x2a9/0x30d
[ 27.408034] [<ffffffff8020f4a4>] sys_mmap+0x92/0xce
[ 27.408339] [<ffffffff8020b65b>] system_call_fastpath+0x16/0x1b
[ 27.408614] ---[ end trace 4b16ad70c09a602d ]---
[ 27.408871] dmidecode:4913 reserve_pfn_range ioremap_change_attr failed write-back for cff6a000-cff6b000
This is wih track_pfn_vma_new trying to keep identity map in sync.
The address cff6a000 is the ACPI region according to e820.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
[ 0.000000] BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000cc000 - 00000000000d0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cff60000 (usable)
[ 0.000000] BIOS-e820: 00000000cff60000 - 00000000cff69000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cff69000 - 00000000cff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cff80000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000230000000 (usable)
And is not mapped as per init_memory_mapping.
[ 0.000000] init_memory_mapping: 0000000000000000-00000000cff60000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000230000000
We can add logic to check for this. But, there can also be other holes in
identity map when we have 1GB of aligned reserved space in e820.
This patch handles it by removing the WARN_ON and returning a specific
error value (EFAULT) to indicate that the address does not have any
identity mapping.
The code that tries to keep identity map in sync can ignore
this error, with other callers of cpa still getting error here.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: avoid warning message, potentially solve 3D performance regression
Change x86 PAT code to return compatible memtype if the exact memtype that
was requested in remap_pfn_rage and friends is not available due to some
conflict.
This is done by returning the compatible type in pgprot parameter of
track_pfn_vma_new(), and the caller uses that memtype for page table.
Note that track_pfn_vma_copy() which is basically called during fork gets the
prot from existing page table and should not have any conflict. Hence we use
strict memtype check there and do not allow compatible memtypes.
This patch fixes the bug reported here:
http://marc.info/?l=linux-kernel&m=123108883716357&w=2
Specifically the error message:
X:5010 map pfn expected mapping type write-back for d0000000-d0101000,
got write-combining
Should go away.
Reported-and-bisected-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Change the protection parameter for track_pfn_vma_new() into a pgprot_t pointer.
Subsequent patch changes the x86 PAT handling to return a compatible
memtype in pgprot_t, if what was requested cannot be allowed due to conflicts.
No fuctionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Move the new memtype old memtype allowed check to header so that is can be
shared by other users. Subsequent patch uses this in pat.c in remap_pfn_range()
code path. No functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce kernel image size
Hugh Dickins noticed that older gcc versions when the kernel
is built for code size didn't inline some of the bitops.
Mark all complex x86 bitops that have more than a single
asm statement or two as always inline to avoid this problem.
Probably should be done for other architectures too.
Ingo then found a better fix that only requires
a single line change, but it unfortunately only
works on gcc 4.3.
On older gccs the original patch still makes a ~0.3% defconfig
difference with CONFIG_OPTIMIZE_INLINING=y.
With gcc 4.1 and a defconfig like build:
6116998 1138540 883788 8139326 7c323e vmlinux-oi-with-patch
6137043 1138540 883788 8159371 7c808b vmlinux-optimize-inlining
~20k / 0.3% difference.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix potential boot crash on MAXSMP
Remove code left over by:
50c668d: Revert "cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read
That cmd.cpumask is not allocated anymore. No impact on default !MAXSMP
kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To increase the amount of code that's built for a defconfig build.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerMac kernel occasionally fails to bring up the secondary CPUs on
SMP, the trigger factor seem to be fairly random and related to location
of code and data.
This appears to be due to the initial loading of the TOC value by the
secondary processor which now happens before we clear HID4:RM_CI (Real
Mode Cache Invalidate). This bit should really be cleared before we do
any load or store other than fetching code.
This fix works based on the assumption that all SMP 64-bit PowerMacs use
variants of the 970, which fortunately is true, by explicitely clearing
that bit, adding an slbia for good measure as RM_CI mode is known to
create bogus ERAT entries.
I also removed some spurrious debug output that was left enabled by
mistake while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The per_cpu__ prefix on DECLARE_PER_CPU'd variables is going away;
rename cache_dir to cache_dir_pcpu.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enforce that the crash kernel region never overlaps the current kernel,
as it will be written directly on kexec load.
Also, default to the previous KDUMP_KERNELBASE if the start is 0.
Other architectures (x86, ia64) state that specifying the start address
0 (or omitting it) will result in the kernel allocating it. Before the
relocatable patch in 2.6.28, powerpc would adjust any other start value
to the hardcoded KDUMP_KERNELBASE of 32M.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are declaring the dummy section (used to work around a binutils
bug) as PT_NOTE, but we don't have enough bytes for it to be a valid
note header, and kexec userspace complains:
Warning: Elf Note name is not null terminated
Warning: append= option is not passed. Using the first kernel root partition
Warning: Elf Note name is not null terminated
Instead of using the arbitray value 0xf177 (aka "fill"), declare a
no-name no-description note of type 0.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparc64: Fix cpumask related build failure
smp_call_function_single(): be slightly less stupid, fix
smp_call_function_single(): be slightly less stupid
rcu: fix bug in rcutorture system-shutdown code
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Fix asm/signal.h for 32-bit.
sparc: Eliminate PROMLIB_INTERNAL as it does nothing
sparc: Kill exports of prom internal functions
sparc64: move EXPORT_SYMBOL to the symbols definition
sparc: move EXPORT_SYMBOL to the symbols definition
sparc: Create a new file lib/ksyms.c and add export of all symbols defined in assembler in lib/ to this file.
sparc: Most unaligned_64.c tweaks for branch tracer warnings.
sparc: Fix sun4d_irq.c build.
sparc: Update 32-bit defconfig.
sparc64: fix warnings in psycho_common after ull conversion
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Pika Warp appliance watchdog timer
[WATCHDOG] Enable watchdog timer on GE Fanuc's SBC610
[WATCHDOG] Basic support for GE Fanuc's FPGA based watchdog timer
[WATCHDOG] wm8350: Fix section annotations
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write"
x86: fix apic.c build error on latest git
x86: fix mpparse.c build error on latest git
x86: avoid theoretical vmalloc fault loop
x86, mtrr: fix types used in userspace exported header
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Counterpart of commit 08a3db94f2 ("m68k: Add
NOTES to init data so its discarded at boot") for sun3 build.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Replace external declarations by proper includes where availiable.
The accesses to some symbols had to be modified, as before they were
declared using e.g. "extern int _end", while asm-generic/sections.h uses
e.g. "extern char _end[]"
- Remove unused or superfluous external declarations
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
arch/m68k/kernel/.gitignore: Added vmlinux.lds to .gitignore file because it
shouldn't be tracked.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This reverts commit e0c7317557.
This patch was wrong, as lockdep (and thus the irq state tracer)
aren't nmi safe. People are already seeing lockdep warnings due
to this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 7503bfbae8.
Dieter Ries reported bootup soft-hangs and bisected it back to
this commit, and reverting this commit gave him a working system.
The commit introduces work_on_cpu() use into the cpufreq code,
but that is subtly problematic from a lock hierarchy POV: the
hotplug-cpu lock is an highlevel lock that is taken before
lowlevel locks, and in this codepath we are called with the
policy lock taken.
Dieter did not have lockdep enabled so we dont have a nice stack
trace proof for this, but using work_on_cpu() in such a lowlevel
place certainly looks wrong, so we revert the patch.
work_on_cpu() needs to be reworked to be more generally usable.
Reported-by: Dieter Ries <clip2@gmx.de>
Tested-by: Dieter Ries <clip2@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in apic.c - later on
I will fix this by removing non-smp data from smp.h
Also fix the __inquire_remote_apic() prototype/inline.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in mpparse.c - later on
I will fix this by removing non-smp data from smp.h.
Reported-by: Petr Titera <P.Titera@century.cz>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ajith Kumar noticed:
I was going through the vmalloc fault handling for x86_64 and am unclear
about the following lines in the vmalloc_fault() function.
pgd = pgd_offset(current->mm ?: &init_mm, address);
pgd_ref = pgd_offset_k(address);
Here the intention is to get the pgd corresponding to the current process
and sync it up with the pgd in init_mm(obtained from pgd_offset_k).
However, for kernel threads current->mm is NULL and hence pgd =
pgd_offset(init_mm, address) = pgd_ref which means the fault handler
returns without setting the pgd entry in the MM structure in the context
of which the kernel thread has faulted. This could lead to never-ending
faults and busy looping of kernel threads like pdflush. So, shouldn't the
pgd = pgd_offset(current->mm ?: &init_mm, address); be pgd =
pgd_offset(current->active_mm ?: &init_mm, address);
We can use active_mm unconditionally because it should be always set.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Without this, the pxa2xx-flash driver cannot be used as a module.
Reported-by: Chris Lawrence <chrisdl@netspace.net.au>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-w90x900/mach-w90p910evb.c:65: error: 'W90X900_PA_UART' undeclared here (not in a function)
and silence warnings caused by inappropriate inclusion of mach/system.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alexander Beregalov reported that this warning is caused by the HPET code:
> hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> hpet0: 3 comparators, 64-bit 14.318180 MHz counter
> ODEBUG: object is on stack, but not annotated
> ------------[ cut here ]------------
> WARNING: at lib/debugobjects.c:251 __debug_object_init+0x2a4/0x352()
> Bisected down to 26afe5f2fb
> (x86: HPET_MSI Initialise per-cpu HPET timers)
The commit is fine - but the on-stack workqueue entry needs annotation.
Reported-and-bisected-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix breakage from commit 278892736e:
i.MX Framebuffer: rename imxfb_mach_info to imx_fb_platform_data
Forgot to rename the parts in arch/arm/mach-imx/generic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The LCDC controller register definitions are now part of the driver
itself, so remove them from imx-regs.h to avoid redefitions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This updates the cpufreq drivers in arch/powerpc so they build again
after the core cpufreq changes that broke them in commit
in835481d9bcd65720b473db6b38746a74a3964218.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpumask_of_pcibus() was missing - this triggers on NUMA builds.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium OCTEON, compute the return epc value for OCTEON specific
branch instructions.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For OCTEON, implement a save and restore of the multiplier state
across context switches.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add in the cop2 and cvmseg state info to the known proc reg
data for Cavium so that it can be tracked, saved, restored.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow precedent of other boards, and hook-up the CPU specific cache
init.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add OCTEON constants to asm/cpu.h and asm/module.h.
Add probe function for Cavium OCTEON CPUs and hook it up.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gas from binutils 2.19 fails to compile some cop1 instructions with
-march=octeon. Since the cop1 instructions are present in mips1, use
that arch instead. This will be fixed in binutils 2.20.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If on Cavium, be aware of cop2 and hwrena during do_cpu().
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium CPU, we treat the same as R10000, in that all hazards
are dealt with in hardware.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files are used to coordinate resource sharing between all of
the programs running on the OCTEON SOC. The OCTEON processor has many
CPU cores (current parts have up to 16, but more are possible). It
also has a variety of on-chip hardware blocks for things like network
acceleration, encryption and RAID.
One typical configuration is to run Linux on several of the CPU cores,
and other dedicated applications on the other cores.
Resource allocation between the various programs running on the system
(Linux kernel and other dedicated applications) needs to be
coordinated. The code we use to do this we call the 'executive'. All
of this resource allocation and sharing code is gathered together in
the executive directory.
Included in the patch set are the following files:
cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation.
All memory used by the Linux kernel is obtained here at boot time.
cvmx-l2c.c -- Coordinates operations on the shared level 2 cache.
octeon-model.c -- Probes chip capabilities and version.
The corresponding headers are in asm/octeon.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/cavium-octeon/executive/Makefile
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-bootmem.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-l2c.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
create mode 100644 arch/mips/cavium-octeon/executive/octeon-model.c
create mode 100644 arch/mips/include/asm/octeon/cvmx-asm.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootmem.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-l2c.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-packet.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-spinlock.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-sysinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx.h
create mode 100644 arch/mips/include/asm/octeon/octeon-feature.h
create mode 100644 arch/mips/include/asm/octeon/octeon-model.h
Here we define the addresses and bit-fields of the Configuration and
Status Registers (CSRs) for some of the hardware functional units on
the OCTEON SOC.
Definitions are needed for:
CIU -- Central Interrupt Unit.
GPIO -- General Purpose Input Output.
IOB -- Input / Output {Busing,Bridge}.
IPD -- Input Packet Data unit.
L2C -- Level-2 Cache controller.
L2D -- Level-2 Data cache.
L2T -- Level-2 cache Tag.
LED -- Light Emitting Diode controller.
MIO -- Miscellaneous Input / Output.
POW -- Packet Order / Work unit.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a 32-bit sparc regression reported by Robert Reif.
_NSIG_BPW needs to be 32 for 32-bit and 64 for 64-bit
Tested-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86: fix section mismatch warnings in mcheck/mce_amd_64.c
x86: offer frame pointers in all build modes
x86: remove duplicated #include's
x86: k8 numa register active regions later
x86: update Alan Cox's email addresses
x86: rename all fields of mpc_table mpc_X to X
x86: rename all fields of mpc_oemtable oem_X to X
x86: rename all fields of mpc_bus mpc_X to X
x86: rename all fields of mpc_cpu mpc_X to X
x86: rename all fields of mpc_intsrc mpc_X to X
x86: rename all fields of mpc_lintsrc mpc_X to X
x86: rename all fields of mpc_iopic mpc_X to X
x86: irqinit_64.c init_ISA_irqs should be static
Documentation/x86/boot.txt: payload length was changed to payload_length
x86: setup_percpu.c fix style problems
x86: irqinit_64.c fix style problems
x86: irqinit_32.c fix style problems
x86: i8259.c fix style problems
x86: irq_32.c fix style problems
x86: ioport.c fix style problems
...
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
[IA64] fix typo in cpumask_of_pcibus()
x86: fix x86_32 builds for summit and es7000 arch's
cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
cpumask: use cpumask_var_t in acpi-cpufreq.c
cpumask: use work_on_cpu in acpi/cstate.c
cpumask: convert struct cpufreq_policy to cpumask_var_t
cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
x86: cleanup remaining cpumask_t ops in smpboot code
cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
cpumask: update local_cpus_show to use new cpumask API
ia64: cpumask fix for is_affinity_mask_valid()
The MPC5200 PIC driver doesn't correctly update the .status field of
the irq_desc structure when the set_type hook is called. This patch
adds the required code.
Also cleans up the external IRQ typename field to be something easier
to read (very minor).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
strcmp on NULL results in a segmentation fault, also, remove the second,
redundant test on dev
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-nommu:
NOMMU: Support XIP on initramfs
NOMMU: Teach kobjsize() about VMA regions.
FLAT: Don't attempt to expand the userspace stack to fill the space allocated
FDPIC: Don't attempt to expand the userspace stack to fill the space allocated
NOMMU: Improve procfs output using per-MM VMAs
NOMMU: Make mmap allocation page trimming behaviour configurable.
NOMMU: Make VMAs per MM as for MMU-mode linux
NOMMU: Delete askedalloc and realalloc variables
NOMMU: Rename ARM's struct vm_region
NOMMU: Fix cleanup handling in ramfs_nommu_get_umapped_area()
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] update documentation for hvc_iucv kernel parameter.
[S390] hvc_iucv: Special handling of IUCV HVC devices
[S390] hvc_iucv: Refactor console and device initialization
[S390] hvc_iucv: Update function documentation
[S390] hvc_iucv: Limit rate of outgoing IUCV messages
[S390] hvc_iucv: Change IUCV term id and use one device as default
[S390] Use unsigned long long for u64 on 64bit.
[S390] qdio: fix broken pointer in case of CONFIG_DEBUG_FS is disabled
[S390] vdso: compile fix
[S390] remove code for oldselect system call
[S390] types: add/fix types.h include in header files
[S390] dasd: add device attribute to disable blocking on lost paths
[S390] dasd: send change uevents for dasd block devices
[S390] tape block: fix dependencies
[S390] asm-s390/posix_types.h: drop __USE_ALL usage
[S390] gettimeofday.S: removed duplicated #includes
[S390] ptrace: no extern declarations for userspace
Ingo noticed that using signed arithmetic seems to confuse the gcc
inliner, and make it potentially decide that it's all too complicated.
(Yeah, yeah, it's a constant. It's always positive. Still..)
Based-on: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix for the linux/byteorder.h removal.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We found a situation on Linus' machine that the Nvidia timer quirk hit on
a Intel chipset system. The problem is that the system has a fancy Nvidia
card with an own PCI bridge, and the early-quirks code looking for any
NVidia bridge triggered on it incorrectly. This didn't lead a boot
failure by luck, but the timer routing code selecting the wrong timer
first and some ugly messages. It might lead to real problems on other
systems.
I checked all the devices which are currently checked for by early_quirks
and it turns out they are all located in the root bus zero.
So change the early-quirks loop to only scan bus 0. This incidently also
saves quite some unnecessary scanning work, because early_quirks doesn't
go through all the non root busses.
The graphics card is not on bus 0, so it is not matched anymore.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile: (31 commits)
powerpc/oprofile: fix whitespaces in op_model_cell.c
powerpc/oprofile: IBM CELL: add SPU event profiling support
powerpc/oprofile: fix cell/pr_util.h
powerpc/oprofile: IBM CELL: cleanup and restructuring
oprofile: make new cpu buffer functions part of the api
oprofile: remove #ifdef CONFIG_OPROFILE_IBS in non-ibs code
ring_buffer: fix ring_buffer_event_length()
oprofile: use new data sample format for ibs
oprofile: add op_cpu_buffer_get_data()
oprofile: add op_cpu_buffer_add_data()
oprofile: rework implementation of cpu buffer events
oprofile: modify op_cpu_buffer_read_entry()
oprofile: add op_cpu_buffer_write_reserve()
oprofile: rename variables in add_ibs_begin()
oprofile: rename add_sample() in cpu_buffer.c
oprofile: rename variable ibs_allowed to has_ibs in op_model_amd.c
oprofile: making add_sample_entry() inline
oprofile: remove backtrace code for ibs
oprofile: remove unused ibs macro
oprofile: remove unused components in struct oprofile_cpu_buffer
...
* git://git.infradead.org/mtd-2.6: (67 commits)
[MTD] [MAPS] Fix printk format warning in nettel.c
[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nand
[MTD] CFI: remove major/minor version check for command set 0x0002
[MTD] [NAND] ndfc driver
[MTD] [TESTS] Fix some size_t printk format warnings
[MTD] LPDDR Makefile and KConfig
[MTD] LPDDR extended physmap driver to support LPDDR flash
[MTD] LPDDR added new pfow_base parameter
[MTD] LPDDR Command set driver
[MTD] LPDDR PFOW definition
[MTD] LPDDR QINFO records definitions
[MTD] LPDDR qinfo probing.
[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately
[MTD] [NAND] pxa3xx: fix non-page-aligned reads
[MTD] [NAND] fix nandsim sched.h references
[MTD] [NAND] alauda: use USB API functions rather than constants
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] fix m25p80 64-bit divisions
[MTD] fix dataflash 64-bit divisions
[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
...
Fixed up trivial debug conflicts in drivers/mtd/devices/{m25p80.c,mtd_dataflash.c}
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (94 commits)
ACPICA: hide private headers
ACPICA: create acpica/ directory
ACPI: fix build warning
ACPI : Use RSDT instead of XSDT by adding boot option of "acpi=rsdt"
ACPI: Avoid array address overflow when _CST MWAIT hint bits are set
fujitsu-laptop: Simplify SBLL/SBL2 backlight handling
fujitsu-laptop: Add BL power, LED control and radio state information
ACPICA: delete utcache.c
ACPICA: delete acdisasm.h
ACPICA: Update version to 20081204.
ACPICA: FADT: Update error msgs for consistency
ACPICA: FADT: set acpi_gbl_use_default_register_widths to TRUE by default
ACPICA: FADT parsing changes and fixes
ACPICA: Add ACPI_MUTEX_TYPE configuration option
ACPICA: Fixes for various ACPI data tables
ACPICA: Restructure includes into public/private
ACPI: remove private acpica headers from driver files
ACPI: reboot.c: use new acpi_reset interface
ACPICA: New: acpi_reset interface - write to reset register
ACPICA: Move all public H/W interfaces to new hwxface
...
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: export length of os_hpmc vector
parisc: fix kernel crash (protection id trap) when compiling ruby1.9
parisc: Use DEFINE_SPINLOCK
parisc: add uevent helper for parisc bus
parisc: fix ipv6 checksum
parisc: quiet palo not-found message from "which"
parisc: Replace NR_CPUS in parisc code
parisc: trivial fixes
parisc: fix braino in commit adding __space_to_prot
parisc: factor out sid to protid conversion
parisc: use leX_to_cpu in place of __fswabX
parisc: fix GFP_KERNEL use while atomic in unwinder
parisc: remove dead BIO_VMERGE_BOUNDARY and BIO_VMERGE_MAX_SIZE definitions
parisc: set_time() catch errors
parisc: use the new byteorder headers
parisc: drivers/parisc/: make code static
parisc: lib/: make code static
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits)
ioat: fix self test for multi-channel case
dmaengine: bump initcall level to arch_initcall
dmaengine: advertise all channels on a device to dma_filter_fn
dmaengine: use idr for registering dma device numbers
dmaengine: add a release for dma class devices and dependent infrastructure
ioat: do not perform removal actions at shutdown
iop-adma: enable module removal
iop-adma: kill debug BUG_ON
iop-adma: let devm do its job, don't duplicate free
dmaengine: kill enum dma_state_client
dmaengine: remove 'bigref' infrastructure
dmaengine: kill struct dma_client and supporting infrastructure
dmaengine: replace dma_async_client_register with dmaengine_get
atmel-mci: convert to dma_request_channel and down-level dma_slave
dmatest: convert to dma_request_channel
dmaengine: introduce dma_request_channel and private channels
net_dma: convert to dma_find_channel
dmaengine: provide a common 'issue_pending_all' implementation
dmaengine: centralize channel allocation, introduce dma_find_channel
dmaengine: up-level reference counting to the module level
...
As requested by Andrew. Same as what sparc did.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
!CONFIG_SMP:
arch/s390/kernel/vdso.c: In function 'vdso_init':
arch/s390/kernel/vdso.c:325: error: incompatible type for argument 2 of 'vdso_alloc_per_cpu'
Also move the code out of the BUG_ON statement since it won't be
executed on !CONFIG_BUG. And that would be a bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The system call isn't wired up on s390. Just delete the dead code.
Also we use the common code sys_ptrace system call, so the sys_ptrace
declaration is pointless is well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
/include/asm/chpid.h:12: include of <linux/types.h> is preferred over <asm/types.h>
/include/asm/chsc.h:15: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/cmb.h:28: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/dasd.h:195: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/kvm.h:16: include of <linux/types.h> is preferred over <asm/types.h>
/include/asm/kvm.h:30: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/qeth.h:24: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/schid.h:5: found __[us]{8,16,32,64} type without #include <linux/types.h>
/include/asm/swab.h:12: include of <linux/types.h> is preferred over <asm/types.h>
/include/asm/swab.h:19: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the connection between host and storage server is lost, the
dasd device driver usually blocks all I/O on affected devices and
waits for them to reappear. In some setups however it would be
better if the I/O is returned as error so that device can be
recovered by some other means, eg. in a raid or multipath setup.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bring s390 in line with all the other ports. Not sure how s390 missed
this change as all the other arches were being updated ...
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux390@de.ibm.com
CC: linux-s390@vger.kernel.org
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
/include/asm/ptrace.h:275: extern's make no sense in userspace
/include/asm/ptrace.h:279: extern's make no sense in userspace
/include/asm/ptrace.h:280: extern's make no sense in userspace
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The Cx Register address obtained from the _CST object is used as the MWAIT
hints if the register type is FFixedHW. And it is used to check whether
the Cx type is supported or not.
On some boxes the following Cx state package is obtained from _CST object:
>{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000889759, // Address
0x03, // Access Size
)
},
0x03,
0xF5,
0x015E }
In such case we should use the bit[7:4] of Cx address to check whether
the Cx type is supported or not.
mask the MWAIT hint to avoid array address overflow
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by:Venki Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
__prom_getchild() and __prom_getsibling() are not used anywhere, so
don't export them.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all applicable EXPORT_SYMBOL()s to the file where the respective
symbol is defined.
Removed all the includes that are no longer needed in sparc_ksyms_64.c
Comment all remaining EXPORT_SYMBOL()s in sparc_ksyms_64.c
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Additions by Julian Calaby:
* Moved EXPORT_SYMBOL()s for prom functions to their rightful places.
* Made some minor cleanups to the includes and comments of sparc_ksyms_64.c
* Updated and tidied commit message.
* Rebased patch over sparc-2.6.git HEAD.
* Ensured that all modified files have the correct includes.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all applicable EXPORT_SYMBOL()s to the file where the respective
symbol is defined.
Removed all the includes that are no longer needed in sparc_ksyms_32.c
Comment all remaining EXPORT_SYMBOL()s in sparc_ksyms_32.c
Two symbols are shared with sparc64 thus the exports were removed from
the sparc_ksyms_64.c too, along with the include their ommission made
redundant.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Additions by Julian Calaby:
* Moved EXPORT_SYMBOL()s for prom functions to their rightful places.
* Made some minor cleanups to the includes and comments of sparc_ksyms_32.c
* Made another subtraction from sparc_ksyms_64.c
* Updated and tidied commit message.
* Rebased patch over sparc-2.6.git HEAD.
* Ensured that all modified files have the correct includes.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the duplicate entries from kernel/sparc_ksyms_*.c
The rationale behind this is that the EXPORT_SYMBOL() should be close to
their definition and we cannot add designate a symbol to be exported in
assembler so at least put it in a file in the same directory.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Additions by Julian Calaby:
* Rebased over sparc-2.6.git HEAD
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/sparc/kernel/unaligned_64.c: In function 'handle_lddfmna':
arch/sparc/kernel/unaligned_64.c:592: warning: 'second' may be used uninitialized in this function
Signed-off-by: David S. Miller <davem@davemloft.net>
After conversion to use unsigned long long for u64
I saw following warnings:
CC arch/sparc/kernel/psycho_common.o
arch/sparc/kernel/psycho_common.c: In function `psycho_check_stc_error':
arch/sparc/kernel/psycho_common.c:104: warning: long long unsigned int format, long unsigned int arg (arg 4)
arch/sparc/kernel/psycho_common.c:104: warning: long long unsigned int format, long unsigned int arg (arg 5)
arch/sparc/kernel/psycho_common.c:114: warning: long long unsigned int format, long unsigned int arg (arg 4)
arch/sparc/kernel/psycho_common.c:114: warning: long long unsigned int format, long unsigned int arg (arg 5)
arch/sparc/kernel/psycho_common.c:114: warning: long long unsigned int format, long unsigned int arg (arg 6)
arch/sparc/kernel/psycho_common.c:114: warning: long long unsigned int format, long unsigned int arg (arg 7)
arch/sparc/kernel/psycho_common.c: In function `psycho_dump_iommu_tags_and_data':
arch/sparc/kernel/psycho_common.c:187: warning: long long unsigned int format, long unsigned int arg (arg 8)
arch/sparc/kernel/psycho_common.c:193: warning: long long unsigned int format, long unsigned int arg (arg 6)
arch/sparc/kernel/psycho_common.c: In function `psycho_pcierr_intr':
arch/sparc/kernel/psycho_common.c:333: warning: long long unsigned int format, long unsigned int arg (arg 3)
arch/sparc/kernel/psycho_common.c:333: warning: long long unsigned int format, long unsigned int arg (arg 4)
This is due to different integer promotion in my 32 bit hosted gcc.
The fix is to force a few constants to ULL.
The following stands out from the rest:
+#define PSYCHO_IOMMU_TAG_VPAGE 0x7ffffULL
+#define PSYCHO_IOMMU_DATA_PPAGE 0xfffffffULL
They were needed otherwise the expression:
(data_val & PSYCHO_IOMMU_DATA_PPAGE) << IOMMU_PAGE_SHIFT)
were promoted to a unsigned long and not a unsigned long long as expected.
I tried the alternative solution and made IOMMU_PAGE_SHIFT an ULL but that did not help.
The only way gcc would make this expression an unsigned long long was to
define PSYCHO_IOMMU_DATA_PPAGE as ULL. The alternative to add a cast was
not considered a valid solution.
We had this issue in two places and this were the only places the above
two constants are used.
A small coding style diff sneaked in too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
serial: Add driver for the Cell Network Processor serial port NWP device
powerpc: enable dynamic ftrace
powerpc/cell: Fix the prototype of create_vma_map()
powerpc/mm: Make clear_fixmap() actually work
powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
powerpc: Export cacheable_memzero as its now used in a driver
powerpc: Fix missing semicolons in mmu_decl.h
powerpc/pasemi: local_irq_save uses an unsigned long
powerpc/cell: Fix some u64 vs. long types
powerpc/cell: Use correct types in beat files
powerpc: Use correct type in prom_init.c
powerpc: Remove unnecessary casts
mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
mtd/ps3vram: Use msleep in waits
mtd/ps3vram: Use proper kernel types
mtd/ps3vram: Cleanup ps3vram driver messages
mtd/ps3vram: Remove ps3vram debug routines
mtd/ps3vram: Add modalias support to the ps3vram driver
mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
...
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for the introduction of a generic swap() macro.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/arm/mach-pnx4008/include/mach/gpio.h:214: error: implicit declaration of function 'IO_ADDRESS'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
include/asm-generic/pgtable.h:305: warning: 'struct vm_area_struct' declared inside parameter list
include/asm-generic/pgtable.h:305: warning: its scope is only this definition or declaration, which is probably not what you want
include/asm-generic/pgtable.h:317: warning: 'struct vm_area_struct' declared inside parameter list
include/asm-generic/pgtable.h:331: warning: 'struct vm_area_struct' declared inside parameter list
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-realview/platsmp.c:140: error: 'jiffies' undeclared (first use in this function)
drivers/amba/bus.c:246: error: 'NO_IRQ' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise the mv643xx_eth driver will assume 133 MHz which is incorrect.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since mci.h has been moved, use the new include path.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix IRQ_EINT_GROUP which has an extra _ in it and
an error in the IRQ offset.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
[ben-linux@fluff.org: rewrite description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The dc21285 requests a number of IRQs that it doesn't really
care whether they get added. Change to use a macro that ensures
that at-least the user gets warned if they fail to add, which
also stops the warnings from __unused_result on request_irq().
dc21285.c:337: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:339: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:341: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:343: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:345: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
isa_init_irq() is defined in arch/arm/mach-footbridge/isa-irq.c
and used in arch/arm/mach-footbridge/common.c but there is no
definition in any header. Move the definition in common.c to
common.h to stop the sparse warning:
isa-irq.c:118:13: warning: symbol 'isa_init_irq' was not declared.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch/arm/kernel/isa.c should include <linux/io.h> to get the
definition of register_io_ports() at-least when compiling for
footbridge to fix the following sparse warning:
isa.c:68:1: warning: symbol 'register_isa_ports' was not declared.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the SPU event based profiling funcitonality for the
IBM Cell processor. Previously, the CELL OProfile kernel code supported
PPU event, PPU cycle profiling and SPU cycle profiling. The addition of
SPU event profiling allows the users to identify where in their SPU code
various SPU evnets are occuring. This should help users further identify
issues with their code. Note, SPU profiling has some limitations due to HW
constraints. Only one event at a time can be used for profiling and SPU event
profiling must be time sliced across all of the SPUs in a node.
The patch adds a new arch specific file to the OProfile file system. The
file has bit 0 set to indicate that the kernel supports SPU event profiling.
The user tool must check this file/bit to make sure the kernel supports
SPU event profiling before trying to do SPU event profiling. The user tool
check is part of the user tool patch for SPU event profiling.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch restructures and cleans up the code a bit to make it
easier to add new functionality later. The patch makes no
functional changes to the existing code.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Make VMAs per mm_struct as for MMU-mode linux. This solves two problems:
(1) In SYSV SHM where nattch for a segment does not reflect the number of
shmat's (and forks) done.
(2) In mmap() where the VMA's vm_mm is set to point to the parent mm by an
exec'ing process when VM_EXECUTABLE is specified, regardless of the fact
that a VMA might be shared and already have its vm_mm assigned to another
process or a dead process.
A new struct (vm_region) is introduced to track a mapped region and to remember
the circumstances under which it may be shared and the vm_list_struct structure
is discarded as it's no longer required.
This patch makes the following additional changes:
(1) Regions are now allocated with alloc_pages() rather than kmalloc() and
with no recourse to __GFP_COMP, so the pages are not composite. Instead,
each page has a reference on it held by the region. Anything else that is
interested in such a page will have to get a reference on it to retain it.
When the pages are released due to unmapping, each page is passed to
put_page() and will be freed when the page usage count reaches zero.
(2) Excess pages are trimmed after an allocation as the allocation must be
made as a power-of-2 quantity of pages.
(3) VMAs are added to the parent MM's R/B tree and mmap lists. As an MM may
end up with overlapping VMAs within the tree, the VMA struct address is
appended to the sort key.
(4) Non-anonymous VMAs are now added to the backing inode's prio list.
(5) Holes may be punched in anonymous VMAs with munmap(), releasing parts of
the backing region. The VMA and region structs will be split if
necessary.
(6) sys_shmdt() only releases one attachment to a SYSV IPC shared memory
segment instead of all the attachments at that addresss. Multiple
shmat()'s return the same address under NOMMU-mode instead of different
virtual addresses as under MMU-mode.
(7) Core dumping for ELF-FDPIC requires fewer exceptions for NOMMU-mode.
(8) /proc/maps is now the global list of mapped regions, and may list bits
that aren't actually mapped anywhere.
(9) /proc/meminfo gains a line (tagged "MmapCopy") that indicates the amount
of RAM currently allocated by mmap to hold mappable regions that can't be
mapped directly. These are copies of the backing device or file if not
anonymous.
These changes make NOMMU mode more similar to MMU mode. The downside is that
NOMMU mode requires some extra memory to track things over NOMMU without this
patch (VMAs are no longer shared, and there are now region structs).
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Rename ARM's struct vm_region so that I can introduce my own global version
for NOMMU. It's feasible that the ARM version may wish to use my global one
instead.
The NOMMU vm_region struct defines areas of the physical memory map that are
under mmap. This may include chunks of RAM or regions of memory mapped
devices, such as flash. It is also used to retain copies of file content so
that shareable private memory mappings of files can be made. As such, it may
be compatible with what is described in the banner comment for ARM's vm_region
struct.
Signed-off-by: David Howells <dhowells@redhat.com>
This patch enables dynamic ftrace. The PowerPC port was dependent on
other code not yet in mainline. Now that the code is, we can now
let PowerPC compile with dynamic ftrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clear_fixmap() routine issues map_page() with flags set to 0.
Currently this causes a BUG_ON() inside the map_page(), as it assumes
that a PTE should be clear before mapping.
This patch makes the map_page() to trigger the BUG_ON() only if the
flags were set.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces internal registers dump implementation with
ppc_save_regs(). From now on PPC64 and PPC32 are using the same
code for crash_setup_regs().
NOTE: The old regs dump implementation was capturing SP (r1) directly
as is, so you could see crash_kexec() function on top of the back-trace.
But ppc_save_regs() goes up one stack frame, so you'll not see it
anymore, at the top-level you'll see who actually triggered the crash
dump instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale PowerPC specific gianfar driver (gig-e) uses
cacheable_memzero for performance reasons we need to export
the symbol to allow the driver to be built as a module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a brown paper bag from one of my earlier patches that
breaks build on 40x and 8xx.
And yes, I've now added 40x and 8xx to my list of test configs :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[Split from a larger patch - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in/out_be64() work on u64s.
The first parameter to ppc_md.ioremap is a phys_addr_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only pass the address of a u64 if that is what the function requires.
[Split out of a larger patch - sfr]
[update comment - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_entryp is a "u64 *" not an "unsigned long *".
[Split from a large patch -sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_get_flat_dt_prop() returns a "void *", so we don't need to cast when
assigning its result to a pointer variable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable RELOCATABLE option if user selects CRASH_DUMP option. Without this
patch user has to first select RELOCATABLE option and then has to enable
CRASH_DUMP option.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So change the flags member of struct spu from u64 to unsigned long.
This change will also prevent some warnings when we change u64 to unsigned
long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These ioctls take a struct serial_rs485
(see linux/serial.h) as argument. They are already available
on x86. This patch adds them for the powerpc architecture.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
X has been failing to start on my quad G5 powermac since commit
1fd0f52583 ("powerpc: Fix domain numbers
in /proc on 64-bit") went in. The reason is that the change allows X
to see the PCI-PCI bridge above the video card (previously it was
obscured by the fact that there were two "00" directories in
/proc/bus/pci), and the pciconfig_iobase system call on the bridge is
failing because of a hack that we have to return information about the
AGP bus when X asks about bus 0. This machine doesn't have an AGP bus
(it has PCI Express) and so the pciconfig_iobase call is returning -1,
which ultimately causes X to fail to start.
This fixes it by checking that we have an AGP bridge before
redirecting the pciconfig_iobase call to return information about the
AGP bus. With this, X starts successfully both on a quad G5 with
PCI Express and on an older dual G5 with AGP.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code for providing processor cache information in sysfs
has the following deficiencies:
- several complex functions that are hard to understand
- implicit recursion (cache_desc_release -> kobject_put -> cache_desc_release)
- explicit recursion (create_cache_index_info)
- use of two per-cpu arrays when one would suffice
- duplication of work on systems where CPUs share cache
Also, when I looked at implementing support for a shared_cpu_map
attribute, it was pretty much impossible to handle hotplug without
checking every single online CPU's cache_desc list and fixing things
up... not that this is a hot path, but it would have introduced
O(n^2)-ish behavior during boot. Addressing this involved rethinking
the core data structures used, which didn't lend itself to an
incremental approach.
This implementation maintains a "forest" (potentially more than one
tree) of cache objects which reflects the system's cache topology.
Cache objects are instantiated as needed as CPUs come online. A
per-cpu array is used mainly for sysfs-related bookkeeping; the
objects in the array just point to the appropriate points in the
forest.
This maintains compatibility with the existing code and includes some
enhancements:
- Implement the shared_cpu_map attribute, which is essential for
enabling userspace to discover the system's overall cache topology.
- Use cache-block-size properties if cache-line-size is not available.
I chose to place this implementation in a new file since it would have
roughly doubled the size of sysfs.c, which is already kind of messy.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The non-zero return from the prepare callback is returned by sys_kexec_load()
to userspace, indicating that kexec is not supported on the machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Both users of careful_allocation() immediately memset() the
result. So, just do it in one place.
Also give careful_allocation() a 'z' prefix to bring it in
line with kzmalloc() and friends.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we memset() the result in both of the uses here,
just make careful_alloc() return a virtual address.
Also, add a separate variable to store the physial
address that comes back from the lmb_alloc() functions.
This makes it less likely that someone will screw it up
forgetting to convert before returning since the vaddr
is always in a void* and the paddr is always in an
unsigned long.
I admit this is arbitrary since one of its users needs
a paddr and one a vaddr, but it does remove a good
number of casts.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we fail a bootmem allocation, the bootmem code itself
panics. No need to redo it here.
Also change the wording of the other panic. We don't
strictly have to allocate memory on the specified node.
It is just a hint and that node may not even *have* any
memory on it. In that case we can and do fall back to
other nodes.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The behavior in careful_allocation() really confused me
at first. Add a comment to hopefully make it easier
on the next doofus that looks at it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes some unbalanced OF node references in the
powermac code
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's a problem on some embedded platforms when we re-assign
everything on PCI, such as 44x. The generic code tries to avoid
assigning devices to addresses overlapping the low legacy
addresses such as VGA hard decoded areas using constants that
are unfortunately no good for us, as they don't take into account
the address translation we do to access PCI busses.
Thus we end up allocating things like IO BARs to 0, which is
technically legal, but will shadow hard decoded ports for use
by things like VGA cards.
This works around it by attempting to reserve legacy regions
before we try to assign addresses.
NOTE: This may have nasty side effects in cases I haven't tested
yet:
- We try to use FW mappings (ie. powermac) and the FW has allocated
a conflicting address over those legacy regions. This will typically
happen. I would expect the new code to just fail with an informative
message without harm but I haven't had a chance to test that scenario
yet.
- A device with fixed BARs overlapping those legacy addresses such
as an IDE controller in legacy mode is in the system. I don't know
for sure yet what will happen there, I have to test :-)
Ideally, we should change PCIBIOS_MIN_IO/MIN_MEM accross the board
to take a bus pointer so they can provide appropriate per-bus translated
values to the generic code but that's a more invasive patch. I will
do that in the future, but in the meantime, this fixes the problem
locally
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Work around branch tracer warning.
sparc64: Fix unsigned long long warnings in drivers.
sparc64: Use unsigned long long for u64.
sparc: refactor code in fault_32.c
sparc64: refactor code in init_64.c
sparc64: refactor code in viohs.c
sparc: make proces_ver_nack a bit more readable
As reported by Sam Ravnborg, Gcc-3.4.5 does not handle:
if (get_user() || get_user())
with the new branch tracer enabled.
Just seperate it out into seperate statements for now
so people can get work done.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This patch creates the new functions
oprofile_write_reserve()
oprofile_add_data()
oprofile_write_commit()
and makes them part of the oprofile api.
Signed-off-by: Robert Richter <robert.richter@amd.com>
The new ring buffer implementation allows the storage of samples with
different size. This patch implements the usage of the new sample
format to store ibs samples in the cpu buffer. Until now, writing to
the cpu buffer could lead to incomplete sampling sequences since IBS
samples were transfered in multiple samples. Due to a full buffer,
data could be lost at any time. This can't happen any more since the
complete data is reserved in advance and then stored in a single
sample.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Special events such as task or context switches are marked with an
escape code in the cpu buffer followed by an event code or a task
identifier. There is one escape code per event. To make escape
sequences also available for data samples the internal cpu buffer
format must be changed. The current implementation does not allow the
extension of event codes since this would lead to collisions with the
task identifiers. To avoid this, this patch introduces an event mask
that allows the storage of multiple events with one escape code. Now,
task identifiers are stored in the data section of the sample. The
implementation also allows the usage of custom data in a sample. As a
side effect the new code is much more readable and easier to
understand.
Signed-off-by: Robert Richter <robert.richter@amd.com>
This is a global variable defined in fsl_booke_mmu.c with a value that gets
initialized in assembly code in head_fsl_booke.S.
It's never used.
If some code ever does want to know the number of entries in TLB1, then
"numcams = mfspr(SPRN_TLB1CFG) & 0xfff", is a whole lot simpler than a
global initialized during kernel boot from assembly.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some assembly code in head_fsl_booke.S hard-coded the size of struct tlbcam
to 20 when it indexed the TLBCAM table. Anyone changing the size of struct
tlbcam would not know to expect that.
The kernel already has a system to get the size of C structures into
assembly language files, asm-offsets, so let's use it.
The definition of the struct gets moved to a header, so that asm-offsets.c
can include it.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Provides a small speedup when accessing pefetchable ranges. To indicate
that a memory range is prefetchable, mark it in the dts file with 42000000
instead of 02000000.
A powepc pci_controller is allowed three memory ranges, any of which may be
prefetchable. However, the PCI-PCI bridge configuration space only has one
field for "non-prefetchable memory behind bridge", which has a 32 bit
address, and one field for "prefetchable memory behind bridge", which may
have a 64 bit address. These are PCI bus addresses, not CPU physical
addresses.
So really you're only allowed one memory range of each type. And if you
want the range at a PCI address above 32 bits you must make it
prefetchable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that sets up the outbound ATMU windows, which is used to map CPU
physical addresses into PCI bus addresses where BARs will be mapped, didn't
work so well.
For one, it leaked the ioremap() of the ATMU registers. Another small bug
was the high 20 bits of the PCI bus address were left as zero. It's legal
for prefetchable memory regions to be above 32 bits, so the high 20 bits
might not be zero.
Mainly, it couldn't handle ranges that were not a power of two in size or
were not naturally aligned. The ATMU windows have these requirements (size
& alignment), but the code didn't bother to check if the ranges it was
programming met them. If they didn't, the windows would silently be
programmed incorrectly.
This new code can handle ranges which are not power of two sized nor
naturally aligned. It simply splits the ranges into multiple valid ATMU
windows. As there are only four windows, pooly aligned or sized ranges
(which didn't even work before) may run out of windows. In this case an
error is printed and an effort is made to disable the unmapped resources.
An improvement that could be made would be to make use of the default
outbound window. Iff hose->pci_mem_offset is zero, then it's possible that
some or all of the ranges might not need an outbound window and could just
use the default window.
The default ATMU window can support a pci_mem_offset less than zero too,
but pci_mem_offset is unsigned. One could say the abilities allowed a
powerpc pci_controller is neither subset nor a superset of the abilities of
a Freescale PCIe controller. Thankfully, the most useful bits are in the
intersection of the two abilities.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixes compile breakage as linux/byteorder.h was removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (171 commits)
Blackfin arch: fix bug - BF527 0.2 silicon has different CPUID (DSPID) value
Blackfin arch: Enlarge flash partition for kenel for bf533/bf537 boards
Blackfin arch: fix bug: kernel crash when enable SDIO host driver
Blackfin arch: Print FP at level KERN_NOTICE
Blackfin arch: drop ad73311 test code
Blackfin arch: update board default configs
Blackfin arch: Set PB4 as the default irq for bf548 board v1.4+.
Blackfin arch: fix typo in early printk bit size processing
Blackfin arch: enable reprogram cclk and sclk for bf518f-ezbrd
Blackfin arch: add SDIO host driver platform data
Blackfin arch: fix bug - kernel stops at initial console
Blackfin arch: fix bug - kernel crash after config IP for ethernet port
Blackfin arch: add sdh support for bf518f-ezbrd
Blackfin arch: fix bug - kernel detects BF532 incorrectly
Blackfin arch: add () to avoid warnings from gcc
Blackfin arch: change HWTRACE Kconfig and set it on default
Blackfin arch: Clean oprofile build path for blackfin
Blackfin arch: remove hardware PM code, oprofile not use it
Blackfin arch: rewrite get_sclk()/get_vco()
Blackfin arch: cleanup and unify the ins functions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Move syscalls.h under arch/avr32/include/asm/
avr32: Define DIE_OOPS
avr32: Remove DMATEST from defconfigs
arch/avr32: Eliminate NULL test and memset after alloc_bootmem
avr32: data param to at32_add_device_mci() must be non-NULL
atmel-mci: move atmel-mci.h file to include/linux
avr32: Hammerhead board support
avr32: Allow reserving multiple pins at once
favr-32: Remove deprecated call
MIMC200: Remove deprecated call
avr: struct device - replace bus_id with dev_name(), dev_set_name()
avr32: Introducing asm/syscalls.h
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
xtensa: Update platform files to reflect new location of the header files.
xtensa: switch to packed struct unaligned access implementation
xtensa: Add xt2000 support files.
xtensa: move headers files to arch/xtensa/include
xtensa: use the new byteorder headers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
pcibios_enable_device() and pcibios_disable_device() don't handle
IRQs for devices that have MSI enabled and it should treat the
devices with MSI-X enabled in the same way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since pci_bus has a struct device, use dev_printk directly instead
of faking it by hand.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the sh simple_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the alpha common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Keep "pin" encoded as it is in the "Interrupt Pin" value in PCI config
space, i.e., 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD.
This makes the bridge INTx swizzle match other architectures.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes pci_get_interrupt_pin() return values encoded
the same way as the "Interrupt Pin" value in PCI config space,
i.e., 1=INTA, ..., 4=INTD.
pirq_bios_set() is the only in-tree caller of pci_get_interrupt_pin()
and pci_get_interrupt_pin() is not exported.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Early type 1 accesses can cause problems on some platforms, and
pci=noearly is supposed to prevent them from occurring. However, early
mcfg probing code uses type 1 and isn't protected by a check for
noearly. This patch fixes that problem.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change PCI bus locality messages so they have a bit more context
and look like the rest of PCI, e.g.,
- bus 01 -> node 0
- bus 04 -> node 0
+ pci 0000:01: bus on NUMA node 0
+ pci 0000:04: bus on NUMA node 0
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are easy to trigger (more or less harmlessly) with multiple video
cards, since the ROM BAR will typically not be given any space by the
BIOS bridge setup. No reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.
This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.
In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implementation of USB device driver integrated in Freescale's i.MXL
processor.
Adds USB device driver for i.MXL.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move otg_get/set/put_transceiver() from omap specific code
to common otg.c so other upcoming drivers can share them.
[ dbrownell@users.sourceforge.net: move to drivers/usb/otg, dox ]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Russell King points out, calling put_device(otg_transceiver->dev)
directly in driver cleanup paths makes assumptions about otg_transceiver
internals.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the UCC_GETH_UPSMR_xxx definitions to qe.h. The ucc_geth driver will
eventually use these instead of the UPSMR_ macros it currently defines.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The general pci resume code can only restore part of the
configuration registers. We need to reconfigure those
registers in the FIXUP_RESUME.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
update bfin-sdh platform data to fix this issue.
Pointed-out-by: Dominik Herwald <d.herwald@dsh-elektronik.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
drop ad73311 test code, this can be done easily from userspace
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Bug: Boot kernel in BF533-EZKIT without set ip during boot,
it stops at initial console.
Restore serial platform_device data to fix this issue.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix typo - kernel crash on bf533-stamp/bf533-ezkit after config IP for ethernet port
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
fix this typo in this patch
Reported-by: Ben Matthews <mben12@gmail.com>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
change the hwtrace description to be less confusing and default it to on
(since there shouldnt be any crashes in the miss handler code itself)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
rewrite get_sclk()/get_vco() based on the assumption sclk/vco never
changes (since today it cannot)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- handle bf531/bf532/bf534/bf536 variants in ipipe.h
- cleanup IPIPE logic for bfin_set_irq_handler()
- cleanup ipipe asm code a bit and add missing ENDPROC()
- simplify IPIPE code in trap_c
- unify some of the IPIPE code and fix style
- simplify DO_IRQ_L1 handling with ipipe code
- revert IRQ_SW_INT# addition from ipipe merge
- remove duplicate get_{c,s}clk() prototypes
]
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Grace Pan <grace.pan@analog.com>: Add case for kgdb test in l1 and l2]
Signed-off-by: Grace Pan <grace.pan@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This is a mixture ofcMichael McTernan's patch and the existing cplb-mpu code.
We ditch the old cplb-nompu implementation, which is a good example of
why a good algorithm in a HLL is preferrable to a bad algorithm written in
assembly. Rather than try to construct a table of all posible CPLBs and
search it, we just create a (smaller) table of memory regions and
their attributes. Some of the data structures are now unified for both
the mpu and nompu cases. A lot of needless complexity in cplbinit.c is
removed.
Further optimizations:
* compile cplbmgr.c with a lot of -ffixed-reg options, and omit saving
these registers on the stack when entering a CPLB exception.
* lose cli/nop/nop/sti sequences for some workarounds - these don't
* make
sense in an exception context
Additional code unification should be possible after this.
[Mike Frysinger <vapier.adi@gmail.com>:
- convert CPP if statements to C if statements
- remove redundant statements
- use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
- the no-mpu code was the last user of MAX_MEM_SIZE and with that rewritten,
we can punt it
- add some BUG_ON() checks to make sure we dont overflow the small
cplb_bounds array
- add i/d cplb entries for the bootrom because there is functions/data in
there we want to access
- we do not need a NULL trailing entry as any time we access the bounds
arrays, we use the nr_bounds variable
]
Signed-off-by: Michael McTernan <mmcternan@airvana.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
If we are running on a chip revision below what we are compiled for,
there will be missing anomaly workarounds, and a panic is inevitable. Do
is sooner, rather than later, so people don't look for bugs that already
have workarounds (that they turned off).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
do not allow people to pass in a diff clkin_hz value when
reprogramming clocks -- it is too late currently
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
rather than use *(unsigned int *)v everywhere, do this once with a local
cpu_num variable
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
