When releasing L2CAP socket which is in BT_CONFIG state l2cap_chan_close
invokes l2cap_send_disconn_req which cancel delayed works which are only
set in BT_CONNECTED state with l2cap_ertm_init. Add state check before
cancelling those works.
...
[ 9668.574372] [21085] l2cap_sock_release: sock cd065200, sk f073e800
[ 9668.574399] [21085] l2cap_sock_shutdown: sock cd065200, sk f073e800
[ 9668.574411] [21085] l2cap_chan_close: chan f073ec00 state BT_CONFIG sk f073e800
[ 9668.574421] [21085] l2cap_send_disconn_req: chan f073ec00 conn ecc16600
[ 9668.574441] INFO: trying to register non-static key.
[ 9668.574443] the code is fine but needs lockdep annotation.
[ 9668.574446] turning off the locking correctness validator.
[ 9668.574450] Pid: 21085, comm: obex-client Tainted: G O 3.5.0+ #57
[ 9668.574452] Call Trace:
[ 9668.574463] [<c10a64b3>] __lock_acquire+0x12e3/0x1700
[ 9668.574468] [<c10a44fb>] ? trace_hardirqs_on+0xb/0x10
[ 9668.574476] [<c15e4f60>] ? printk+0x4d/0x4f
[ 9668.574479] [<c10a6e38>] lock_acquire+0x88/0x130
[ 9668.574487] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574491] [<c1059790>] del_timer_sync+0x50/0xc0
[ 9668.574495] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574515] [<f8aa1c23>] l2cap_send_disconn_req+0xe3/0x160 [bluetooth]
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When new BT USB adapter is plugged in it's configured while still being powered
off (HCI_AUTO_OFF flag is set), thus Set LE will only set dev_flags but won't
write changes to controller. As a result it's not possible to start device
discovery session on LE controller as it uses interleaved discovery which
requires LE Supported Host flag in extended features.
This patch ensures HCI Write LE Host Supported is sent when Set Powered is
called to power on controller and clear HCI_AUTO_OFF flag.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When new BT USB adapter is plugged in it's configured while still being powered
off (HCI_AUTO_OFF flag is set), thus Set SSP will only set dev_flags but won't
write changes to controller. As a result remote devices won't use Secure Simple
Pairing with our device due to SSP Host Support flag disabled in extended
features and may also reject SSP attempt from our side (with possible fallback
to legacy pairing).
This patch ensures HCI Write Simple Pairing Mode is sent when Set Powered is
called to power on controller and clear HCI_AUTO_OFF flag.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
ssid len is 32 bit and needs endian conversion for big endian systems.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for oobirq_entry allocation failure to avoid
NULL pointer dereferencing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver provides the cfg80211 regulatory framework with a set of
custom rules. However, there was a mismatch in number of rules
and the actual rules provided. This resulted in setting an invalid
power level:
ieee80211 phy0: brcms_ops_config: change channel 13
ieee80211 phy0: brcms_ops_config: Error setting power_level (8758364)
Closer look in cfg80211 regulatory blurb showed following bogus rule:
cfg80211: 0 KHz - -60446948 KHz @ 875836468 KHz), (875836468 mBi, 875836468 mBm)
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
connkeys is malloced in nl80211_parse_connkeys() and should
be freed in the error handling case, otherwise it will cause
memory leak.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.
Clear ifmgd->bssid on failure, and notify the driver.
Cc: stable@kernel.org # 3.4+
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the case that the link is already in the connected state and a
Pairing request arrives from the mgmt interface, hci_conn_security()
would be called but it was not considering LE links.
Reported-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.
This also makes it clear that it is checking the security of the link.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Cc: stable@vger.kernel.org
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.
Also changed &bssid to bssid, at the suggestion of Stanislav Yakovlev.
The semantic match that finds the first problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@
*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.
We also remove old rules to that matches product id for Broadcom devices.
Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This return holds the number of bytes transfered (1 byte) or a negative
error code. The type should be int instead of u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrei Emeltchenko