This patch builds upon the new NetLabel address selector functionality by
providing the NetLabel KAPI and CIPSO engine support needed to enable the
new packet-based labeling. The only new addition to the NetLabel KAPI at
this point is shown below:
* int netlbl_skbuff_setattr(skb, family, secattr)
... and is designed to be called from a Netfilter hook after the packet's
IP header has been populated such as in the FORWARD or LOCAL_OUT hooks.
This patch also provides the necessary SELinux hooks to support this new
functionality. Smack support is not currently included due to uncertainty
regarding the permissions needed to expand the Smack network access controls.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reviewed-by: James Morris <jmorris@namei.org>
This patch extends the NetLabel traffic labeling capabilities to individual
packets based not only on the LSM domain but the by the destination address
as well. The changes here only affect the core NetLabel infrastructre,
changes to the NetLabel KAPI and individial protocol engines are also
required but are split out into a different patch to ease review.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reviewed-by: James Morris <jmorris@namei.org>
Create an ordered IP address linked list mechanism similar to the core
kernel's linked list construct. The idea behind this list functionality
is to create an extensibile linked list ordered by IP address mask to
ease the matching of network addresses. The linked list is ordered with
larger address masks at the front of the list and shorter address masks
at the end to facilitate overriding network entries with individual host
or subnet entries.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reviewed-by: James Morris <jmorris@namei.org>
NetLabel has always had a list of backpointers in the CIPSO DOI definition
structure which pointed to the NetLabel LSM domain mapping structures which
referenced the CIPSO DOI struct. The rationale for this was that when an
administrator removed a CIPSO DOI from the system all of the associated
NetLabel LSM domain mappings should be removed as well; a list of
backpointers made this a simple operation.
Unfortunately, while the backpointers did make the removal easier they were
a bit of a mess from an implementation point of view which was making
further development difficult. Since the removal of a CIPSO DOI is a
realtively rare event it seems to make sense to remove this backpointer
list as the optimization was hurting us more then it was helping. However,
we still need to be able to track when a CIPSO DOI definition is being used
so replace the backpointer list with a reference count. In order to
preserve the current functionality of removing the associated LSM domain
mappings when a CIPSO DOI is removed we walk the LSM domain mapping table,
removing the relevant entries.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reviewed-by: James Morris <jmorris@namei.org>
Smack needs to call netlbl_skbuff_err() to let NetLabel do the necessary
protocol specific error handling.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
At some point I think I messed up and dropped the calls to netlbl_skbuff_err()
which are necessary for CIPSO to send error notifications to remote systems.
This patch re-introduces the error handling calls into the SELinux code.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Currently when SELinux fails to allocate memory in
security_netlbl_sid_to_secattr() the NetLabel LSM domain field is set to
NULL which triggers the default NetLabel LSM domain mapping which may not
always be the desired mapping. This patch fixes this by returning an error
when the kernel is unable to allocate memory. This could result in more
failures on a system with heavy memory pressure but it is the "correct"
thing to do.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
It turns out that checking to see if skb->sk is NULL is not a very good
indicator of a forwarded packet as some locally generated packets also have
skb->sk set to NULL. Fix this by not only checking the skb->sk field but also
the IP[6]CB(skb)->flags field for the IP[6]SKB_FORWARDED flag. While we are
at it, we are calling selinux_parse_skb() much earlier than we really should
resulting in potentially wasted cycles parsing packets for information we
might no use; so shuffle the code around a bit to fix this.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
After some discussions with the Smack folks, well just Casey, I now have a
better idea of what Smack wants out of NetLabel in the future so I think it
is now safe to do some API "pruning". If another LSM comes along that
needs this functionality we can always add it back in, but I don't see any
LSMs on the horizon which might make use of these functions.
Thanks to Rami Rosen who suggested removing netlbl_cfg_cipsov4_del() back
in February 2008.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reviewed-by: James Morris <jmorris@namei.org>
We did the right thing in a few cases but there were several areas where we
determined a packet's address family based on the socket's address family which
is not the right thing to do since we can get IPv4 packets on IPv6 sockets.
This patch fixes these problems by either taking the address family directly
from the packet.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
We were doing a lot of extra work in selinux_netlbl_sock_graft() what wasn't
necessary so this patch removes that code. It also removes the redundant
second argument to selinux_netlbl_sock_setsid() which allows us to simplify a
few other functions.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Fix a few sparse warnings. One dealt with a RCU lock being held on error,
another dealt with an improper type caused by a signed/unsigned mixup while
the rest appeared to be caused by using rcu_dereference() in a
list_for_each_entry_rcu() call. The latter probably isn't a big deal, but
I derive a certain pleasure from knowing that the net/netlabel is nice and
clean.
Thanks to James Morris for pointing out the issues and demonstrating how
to run sparse.
Signed-off-by: Paul Moore <paul.moore@hp.com>
This is debatable, but while we're debating it, let's disallow the
combination of splice and an O_APPEND destination.
It's not entirely clear what the semantics of O_APPEND should be, and
POSIX apparently expects pwrite() to ignore O_APPEND, for example. So
we could make up any semantics we want, including the old ones.
But Miklos convinced me that we should at least give it some thought,
and that accepting writes at arbitrary offsets is wrong at least for
IS_APPEND() files (which always have O_APPEND set, even if the reverse
isn't true: you can obviously have O_APPEND set on a regular file).
So disallow O_APPEND entirely for now. I doubt anybody cares, and this
way we have one less gray area to worry about.
Reported-and-argued-for-by: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Jens Axboe <ens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the previous fix, which was completely wrong on closer
inspection. This version has been manually tested with a user-space
test harness and generates sane values. A nearly identical patch has
been boot-tested.
The problem arose from changing how kmalloc/kfree handled alignment
padding without updating ksize to match. This brings it in sync.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Describe the sysfs files that were introduced in the ibmaem driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Creates a name file in the sysfs directory, that
is needed for the libsensors library to work.
Also rename fan1_pwm to pwm1 and scale its value as needed.
This fixes bug #11520:
http://bugzilla.kernel.org/show_bug.cgi?id=11520
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
net: Fix netdev_run_todo dead-lock
tcp: Fix possible double-ack w/ user dma
net: only invoke dev->change_rx_flags when device is UP
netrom: Fix sock_orphan() use in nr_release
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Revert "ax25: Fix std timer socket destroy handling."
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
Symbol name spaghetti which is too complicated to cleanup on this stage
of the release cycle breaks the build on BCM1480 platforms.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Because of rounding, in certain conditions, i.e. when in congestion
avoidance state rho is smaller than 1/128 of the current cwnd, TCP
Hybla congestion control starves and the cwnd is kept constant
forever.
This patch forces an increment by one segment after #send_cwnd calls
without increments(newreno behavior).
Signed-off-by: Daniele Lacamera <root@danielinux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ali Saidi <saidi@engin.umich.edu>
When TCP receive copy offload is enabled it's possible that
tcp_rcv_established() will cause two acks to be sent for a single
packet. In the case that a tcp_dma_early_copy() is successful,
copied_early is set to true which causes tcp_cleanup_rbuf() to be
called early which can send an ack. Further along in
tcp_rcv_established(), __tcp_ack_snd_check() is called and will
schedule a delayed ACK. If no packets are processed before the delayed
ack timer expires the packet will be acked twice.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SLOB's ksize calculation was braindamaged and generally harmlessly
underreported the allocation size. But for very small buffers, it could
in fact overreport them, leading code depending on krealloc to overrun
the allocation and trample other data.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Tested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 135aedc38e, as
requested by Hans Verkuil.
It was a patch for 2.6.28 where the BKL was pushed down from v4l core to
the drivers, not for 2.6.27!
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
* Theodore Ts'o (tytso@mit.edu) wrote:
>
> I've been playing with adding some markers into ext4 to see if they
> could be useful in solving some problems along with Systemtap. It
> appears, though, that as of 2.6.27-rc8, markers defined in code which is
> compiled directly into the kernel (i.e., not as modules) don't show up
> in Module.markers:
>
> kvm_trace_entryexit arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_entryexit arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
>
> (Note the lack of any of the kernel_sched_* markers, and the markers I
> added for ext4_* and jbd2_* are missing as wel.)
>
> Systemtap apparently depends on in-kernel trace_mark being recorded in
> Module.markers, and apparently it's been claimed that it used to be
> there. Is this a bug in systemtap, or in how Module.markers is getting
> built? And is there a file that contains the equivalent information
> for markers located in non-modules code?
I think the problem comes from "markers: fix duplicate modpost entry"
(commit d35cb360c2)
Especially :
- add_marker(mod, marker, fmt);
+ if (!mod->skip)
+ add_marker(mod, marker, fmt);
}
return;
fail:
Here is a fix that should take care if this problem.
Thanks for the bug report!
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Tested-by: "Theodore Ts'o" <tytso@mit.edu>
CC: Greg KH <greg@kroah.com>
CC: David Smith <dsmith@redhat.com>
CC: Roland McGrath <roland@redhat.com>
CC: Sam Ravnborg <sam@ravnborg.org>
CC: Wenji Huang <wenji.huang@oracle.com>
CC: Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While debugging another bug it was found that NetRom socks
are sometimes seen unorphaned in sk_free(). This patch moves
sock_orphan() in nr_release() to the beginning (like in ax25,
or rose).
Reported-and-tested-by: Bernard Pidoux f6bvp <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we reverted 30902dc3cb ("ax25: Fix
std timer socket destroy handling.") we have to put some kind of fix
in to cure the issue whereby unaccepted connections do not get destroyed.
The approach used here is from Tihomir Heidelberg - 9a4gl
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 30902dc3cb.
It causes all kinds of problems, based upon a report by
Bernard (f6bvp) and analysis by Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
On my box it was caused by:
commit 691874fa96
Author: Maciej W. Rozycki <macro@linux-mips.org>
Date: Tue May 27 21:19:51 2008 +0100
x86: I/O APIC: timer through 8259A second-chance
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
http://marc.info/?l=linux-kernel&m=121358440508410&w=4
Matthew Garrett told us about that happening on the nx6125:
http://marc.info/?l=linux-kernel&m=121396307411930&w=4
and then Maciej analysed the breakage on the basis of a DSDT from the
nx6325:
http://marc.info/?l=linux-kernel&m=121401068718826&w=4
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
