Fixed handling of 802.3ad LACPDUs. Do not byte swap data in
place in the packet. Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.
Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add priv_flag to specifically identify bonding-involved devices. Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER). Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.
Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bonding driver fails to adjust its hard_header_len when enslaving
interfaces. Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics. GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming. Enslaving such a device and then transmitting over
it causes a kernel panic.
Patch modified from submitter's original, but submitter agreed with this
patch in private email.
Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded test for NULL. Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow channel bonding to enslave a 10 Gig adapter without errors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for older fiber versions of the SysKonnect board. These chipsets
use an internal PHY so they require special handling. The older sk98lin
driver already supported these
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There seems to be a possible NULL pointer deref bug in
drivers/net/forcedeth.c::nv_loopback_test(). If dev_alloc_skb() fails, the
next line will call skb_put() with a NULL first argument which it'll then
try to deref - kaboom: a NULL pointer deref. Found by coverity (#1337).
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While checking gcc 4.1 -Wextra warnings, I stumbled across the following
two warnings:
drivers/net/phy/phy_device.c:528: warning: comparison of unsigned expression < 0 is always false
drivers/net/phy/phy_device.c:546: warning: comparison of unsigned expression < 0 is always false
Since phy_read() returns an integer and can return negative values, it seems
to me the best way to get proper error handling working again is to make val
an int. Currently it is an u32, so the < 0 check always fails.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
They all contain the same thing. Instead, have a single generic one in
include/asm-generic, and permit an arch to override as needed.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To whoever had written that code:
a) priority of >> is higher than that of &
b) priority of typecast is higher than that of any binary operator
c) learn the fscking C
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ql3xxx_probe() does ioremap and stores result in ->mem_map_registers.
On failure exit it does iounmap() of the same thing.
OTOH, ql3xxx_remove() does iounmap() of ->mmap_virt_base which is
(a) never assigned and
(b) never used other than in that iounmap() call.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some user tools parse /proc/scsi/scsi, so we can't yet change the names.
Change the existing ones back to their old names, and add an admonition
to not make the same mistake that I did.
Andrew Morton reports that this was breaking YDL 4.1 userspace.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (28 commits)
ocfs2: Teach ocfs2_drop_lock() to use ->set_lvb() callback
ocfs2: Remove ->unblock lockres operation
ocfs2: move downconvert worker to lockres ops
ocfs2: Remove unused dlmglue functions
ocfs2: Have the metadata lock use generic dlmglue functions
ocfs2: Add ->set_lvb callback in dlmglue
ocfs2: Add ->check_downconvert callback in dlmglue
ocfs2: Check for refreshing locks in generic unblock function
ocfs2: don't unconditionally pass LVB flags
ocfs2: combine inode and generic blocking AST functions
ocfs2: Add ->get_osb() dlmglue locking operation
ocfs2: remove ->unlock_ast() callback from ocfs2_lock_res_ops
ocfs2: combine inode and generic AST functions
ocfs2: Clean up lock resource refresh flags
ocfs2: Remove i_generation from inode lock names
ocfs2: Encode i_generation in the meta data lvb
ocfs2: Free up some space in the lvb
ocfs2: Remove special casing for inode creation in ocfs2_dentry_attach_lock()
ocfs2: manually d_move() during ocfs2_rename()
[PATCH] Allow file systems to manually d_move() inside of ->rename()
...
* git://git.infradead.org/~dwmw2/khdrs-2.6:
New 'make headers_install_all' target.
Use dependencies for 'make headers_install'.
[S390] Unexport <asm/z90crypt.h>, export <asm/zcrypt.h> in its place.
Remove dead netfilter_logging.h from include/linux/Kbuild
Remove offsetof() from user-visible <linux/stddef.h>
Clean up exported headers on CRIS
Fix v850 exported headers
Don't advertise (or allow) headers_{install,check} where inappropriate.
Remove UML header export
Remove ARM26 header export.
Fix H8300 exported headers.
Fix m68knommu exported headers
Fix exported headers for SPARC, SPARC64
Fix 'make headers_check' on m32r
Fix 'make headers_check' on sh64
Fix 'make headers_check' on sh
[HEADERS] Fix ARM 'make headers_check'
Initial pass of manual conflict resolution in top-level Makefile over
conflicting build rule and headers_install changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (28 commits)
kbuild: add distclean info to 'make help' and more details for 'clean'
dontdiff: add utsrelease.h
kbuild: fix "mkdir -p" usage in scripts/package/mkspec
kbuild: correct and clarify versioning info in Makefile
kbuild: fixup Documentation/kbuild/modules.txt
kbuild: Extend kbuild/defconfig tags support to exuberant ctags
kbuild: fix for some typos in Documentation/makefiles.txt
kbuild: clarify "make C=" build option
Documentaion: update Documentation/Changes with minimum versions
kbuild: update help in top level Makefile
kbuild: fail kernel compilation in case of unresolved module symbols
kbuild: remove debug left-over from Makefile.host
kbuild: create output directory for hostprogs with O=.. build
kbuild: add missing return statement in modpost.c:secref_whitelist()
kbuild: preperly align SYSMAP output
kbuild: make -rR is now default
kbuild: make V=2 tell why a target is rebuild
kbuild: modpost on vmlinux regardless of CONFIG_MODULES
kbuild: ignore references from ".pci_fixup" to ".init.text"
kbuild: linguistic fixes for Documentation/kbuild/makefiles.txt
...
Add distclean info, that was previously missing, to 'make help'.
Also add a few more details to the 'make clean' help text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
"mkdir -p" does not only mean not to complain if the directory already
exists, but also to create the parent directories if needed. This patch
removes "lib" from the list of directories to create as we will also create
"lib/modules".
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The attached patch clarifies the creation of KERNELRELEASE and
corrects an error regarding the use of $(LOCALVERSION).
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The following patch extends kbuild/defconfig tags support to exuberant
ctags. The previous support is only for emacs ctags/etags programs.
This patch also corrects the kconfig regex for the emacs invocation.
Previously it would miss some instances because it assumed /^config
instead of /^[ \t]*config
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
I noticed a few typos while reading makefiles.txt to learn about the
kbuild system. Attached is a patch against 2.6.18 to fix them.
Remove trailing whitespace while we are there..
Signed-off-by: Bryce Harrington <bryce@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Based on conversations with greg kh (and noticing a simple typo),
these are the actual minimal versions for 2.6.18.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
At stage 2 modpost utility is used to check modules. In case of unresolved
symbols modpost only prints warning.
IMHO it is a good idea to fail compilation process in case of unresolved
symbols (at least in modules coming with kernel), since usually such errors
are left unnoticed, but kernel modules are broken.
- new option '-w' is added to modpost:
if option is specified, modpost only warns about unresolved symbols
- modpost is called with '-w' for external modules in Makefile.modpost
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
hostprogs-y only supported creating output directory for the final
program. Extend this to also cover the situation where a .o
file (used when host program is made from compositie objects) is
locate in another directory.
First user of this is the built-in lxdialog that.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Jay Vosburgh