drivers/gpu/drm/i915/i915_irq.c: In function ‘ironlake_irq_postinstall’:
drivers/gpu/drm/i915/i915_irq.c:1618: warning: unused variable ‘pipe’
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Merge in the conflicting eDP fix.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we just need a temporary array whilst performing the relocations for
the execbuffer, first attempt to allocate using kmalloc even if it is
not of order page-0. This avoids the overhead of remapping the
discontiguous array and so gives a moderate boost to execution
throughput.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Seems like we are forever to be cursed with buggy firmware, so allow the
user to explicitly set the panel connection status.
Of secondary utility for cases where I run laptops with the lid closed,
but still want to configure the LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected. A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can enable some safely, but FDI and transcoder interrupts can occur
and block other interrupts from being detected (like port hotplug
events). So keep them disabled by default (they can be re-enabled for
debugging display bringup, but should generally be off).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Copy up lower inode attrs in getattr
ecryptfs: read on a directory should return EISDIR if not supported
eCryptfs: Handle NULL nameidata pointers
eCryptfs: Revert "dont call lookup_one_len to avoid NULL nameidata"
The current code does not follow Intel documentation: It misses some things
and does other, undocumented things. This causes wrong backlight values in
certain conditions. Instead of adding tricky code handling badly documented
and rare corner cases, don't handle combination mode specially at all. This
way PCI_LBPC is never touched and weird things shouldn't happen.
If combination mode is enabled, then the only downside is that changing the
brightness has a greater granularity (the LBPC value), but LBPC is at most
254 and the maximum is in the thousands, so this is no real functional loss.
A potential problem with not handling combined mode is that a brightness of
max * PCI_LBPC is not bright enough. However, this is very unlikely because
from the documentation LBPC seems to act as a scaling factor and doesn't look
like it's supposed to be changed after boot. The value at boot should always
result in a bright enough screen.
IMPORTANT: However, although usually the above is true, it may not be when
people ran an older (2.6.37) kernel which messed up the LBPC register, and
they are unlucky enough to have a BIOS that saves and restores the LBPC value.
Then a good kernel may seem to not work: Max brightness isn't bright enough.
If this happens people should boot back into the old kernel, set brightness
to the maximum, and then reboot. After that everything should be fine.
For more information see the below links. This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=23472http://bugzilla.kernel.org/show_bug.cgi?id=25072
Signed-off-by: Indan Zupancic <indan@nul.nu>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We force particular alignment when we generate attribute structures
when generation MODULE_VERSION() data and we need to make sure that
this alignment is followed when we iterate over these structures,
otherwise we may crash on platforms whose natural alignment is not
sizeof(void *), such as m68k.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
[ There are more issues here, but the fixes are incredibly ugly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the "log_buf_len" description to use [KMG] syntax for the
buffer size.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The '[KMG]' suffix is commonly described after a number of kernel
parameter values documentation. Explicitly state its semantics.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6745/1: kprobes insn decoding fix
ARM: tlb: move noMMU tlb_flush() to asm/tlb.h
ARM: tlb: delay page freeing for SMP and ARMv7 CPUs
ARM: Keep exit text/data around for SMP_ON_UP
ARM: Ensure predictable endian state on signal handler entry
ARM: 6740/1: Place correctly notes section in the linker script
ARM: 6700/1: SPEAr: Correct SOC config base address for spear320
ARM: 6722/1: SPEAr: sp810: switch to slow mode before reset
ARM: 6712/1: SPEAr: replace readl(), writel() with relaxed versions in uncompress.h
ARM: 6720/1: SPEAr: Append UL to VMALLOC_END
ARM: 6676/1: Correct the cpu_architecture() function for ARMv7
ARM: 6739/1: update .gitignore for boot/compressed
ARM: 6743/1: errata: interrupted ICALLUIS may prevent completion of broadcasted operation
ARM: 6742/1: pmu: avoid setting IRQ affinity on UP systems
ARM: 6741/1: errata: pl310 cache sync operation may be faulty
It is found on Dell Inspiron 1018 that the firmware reports that the hardware
killswitch is not supported. This makes the rfkill key not functional.
This patch forces the driver to toggle the firmware rfkill status in the case
that the hardware killswitch is indicated as unsupported by the firmware.
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Tested-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some thinkpad hotkeys report key codes like KEY_FN_F8 when something
like KEY_VOLUMEDOWN is desired. Always provide the scan codes in
addition to the key codes to assist with debugging these issues. Also
send the scan code before the key code to match what other drivers do,
as some userspace utilities expect this ordering.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
6AF4F258-B401-42fd-BE91-3D4AC2D7C0D3 needs to be
6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 to match the hardware alias.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: stable@kernel.org
Most platform/x86 drivers that use INPUT_SPARSEKMAP also depend on INPUT,
so do the same for ideapad-laptop. This fixes a kconfig warning and
subsequent build errors when CONFIG_INPUT is disabled.
warning: (ACER_WMI && ASUS_LAPTOP && DELL_WMI && HP_WMI && PANASONIC_LAPTOP && IDEAPAD_LAPTOP && EEEPC_LAPTOP && EEEPC_WMI && MSI_WMI && TOPSTAR_LAPTOP && ACPI_TOSHIBA) selects INPUT_SPARSEKMAP which has unmet direct dependencies (!S390 && INPUT)
ERROR: "input_free_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_register_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_setup" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_allocate_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_unregister_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_free" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_report_event" [drivers/platform/x86/ideapad-laptop.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is no need to install a chained handler for this hardware. This
is a plain x86 IOAPIC interrupt which is handled by the core code
perfectly fine. There is nothing special about demultiplexing these
gpio interrupts which justifies a custom hack. Replace it by a plain
old interrupt handler installed with request_irq. That makes the code
agnostic about the underlying primary interrupt hardware. The overhead
for this is minimal, but it gives us the advantage of accounting,
balancing and to detect interrupt storms. gpio interrupts are not
really that performance critical.
Patch fixups from akpm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LANMAN response length was changed to 16 bytes instead of 24 bytes.
Revert it back to 24 bytes.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
CC: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
https://bugs.launchpad.net/bugs/613873
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
read() calls against a file descriptor connected to a directory are
incorrectly returning EINVAL rather than EISDIR:
[EISDIR]
[XSI] [Option Start] The fildes argument refers to a directory and the
implementation does not allow the directory to be read using read()
or pread(). The readdir() function should be used instead. [Option End]
This occurs because we do not have a .read operation defined for
ecryptfs directories. Connect this up to generic_read_dir().
BugLink: http://bugs.launchpad.net/bugs/719691
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Cc: <stable@kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 18991197b4 added --build-id
linker option when toolchain supports it. ARM one does, but for some
reason places the section at 0 when linker script doesn't mention it
explicitly.
The 1e621a8e37 worked around the problem
removing this section from binary image with explicit objcopy options,
but it still exists in vmlinux, confusing tools like debuggers and perf.
This problem was discussed here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.html
but the proposed changes to the linker script were substantial.
This patch simply places NOTES (36 bytes long, at least when compiled
with CodeSourcery toolchain) between data and bss, which seem to be
the right place (and suggested by the sample linker script in
include/asm-generic/vmlinux.lds.h).
It is enough to place it correctly in vmlinux (so debuggers are happy):
Section Headers:
[11] .data PROGBITS c07ce000 7ce000 020fc0 00 WA 0 0 32
[12] .notes NOTE c07eefc0 7eefc0 000024 00 AX 0 0 4
[13] .bss NOBITS c07ef000 7eefe4 01e628 00 WA 0 0 32
Program Headers:
LOAD 0x008000 0xc0008000 0xc0008000 0x7e6fe4 0x805628 RWE 0x8000
NOTE 0x7eefc0 0xc07eefc0 0xc07eefc0 0x00024 0x00024 R E 0x4
Section to Segment mapping:
Segment Sections...
00 <...> .data .notes .bss
01 .notes
and to get it exposed as /sys/kernel/notes used by perf tools.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPEAR320_SOC_CONFIG_BASE was wrong, causing the wrong registers to be
accessed.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller. This is required.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>