Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Two be able to network code two packets, one packet must be buffered
until the next is available. This is done in a "coding buffer", which is
essentially a hash table with lists of packets. Each entry in the hash
table corresponds to a specific src-dst pair, which has a linked list of
packets that are buffered.
This patch adds skbs to the buffer just before forwarding them. The
buffer is traversed every 10 ms, where timed skbs are removed from the
buffer and transmitted. To allow experiments with the network coding
scheme, the timeout is tunable through a file in debugfs.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To use network coding efficiently, a relay must know when neighbor nodes
are likely to have enough information to be able to decode a network
coded packet. This is detected by using OGMs from batman-adv to discover
when one neighbor is in range of another neighbor. The relay check the
TLL to detect when an OGM is forwarded from one neighbor by another
neighbor, and thereby knows that the two neighbors are in range and thus
overhear packets sent by each other.
This information is saved in the orig_node struct to be used when
searching for coding opportunities. Two lists are added to the
orig_node struct: One for neighbors that can hear the orig_node
(outgoing nc_nodes) and one for neighbors that the orig_node can hear
(incoming nc_nodes).
Information about nc_nodes is kept for 10 seconds and is available
through debugfs in batman_adv/nc_nodes to use when debugging network
coding.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In C standard any expression different from 0 will be converted to
'true' when casting to bool (whatever is the length of the value).
Therefore all the "!!" conversions can be removed.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_check_unicast_packet() is changed to return a value based on the
reason to drop the packet, which will be useful information for
future users of batadv_check_unicast_packet().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The batadv_priv struct carries a pointer to its own interface
struct. Therefore, it is not necessary to retrieve the soft_iface
via the primary interface.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
QLogic applications use these callbacks to perform
o NIC Partitioning (NPAR) configuration and management
o Diagnostic tests
o Flash access and updates
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
This patch serires implements the following features in CPSW driver
* get/set phy link settings
* interrupt pacing
* get phy id via ioctl cmd SIOCGMIIPHY
Changes from initial version
* Made active-slave common for cpts, ethtool and SIOCGMIIPHY ioctl
* Cleaned CPSW DT binding documentation by seperating slave nodes
under sub-section
* implemented get phy id via ioctl cmd SIOCGMIIPHY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove cast for kmalloc/kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
remove cast for kmalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI header is not needed, so get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using for_each_set_bit_from() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Support sysfs interface for getting the maximal number of virtual functions
of a given physical function.
2. Support sysfs interface for getting and setting the current number of
virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.
This patch prevents said message.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest boards, the CHIP_METAL register contains an incorrect
revision value, so the correct one needs to be obtained in a
different manner.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual functions don't have access to HW registers, therefore most ethtool ops
are forbidden to them. Instead of checking in each op whether the device being
driven is a virtual function or a physical function, this patch creates a
separate ethtool ops struct for virtual functions and uses it to initialize
the ethtool ops of the driver in case it is driving a virtual function device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release (previously leaking) memory when elements are removed from pending
execution lists in the bnx2x driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This uses PTR_RET instead of IS_ERR and PTR_ERR in order to increase
readability.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: <Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast fast leave feature was added sufficient space
was not reserved in the netlink message. This means the flag may be
lost in netlink events and results of queries.
Found by observation while looking up some netlink stuff for discussion with Vlad.
Problem introduced by commit c2d3babfaf
Author: David S. Miller <davem@davemloft.net>
Date: Wed Dec 5 16:24:45 2012 -0500
bridge: implement multicast fast leave
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in order to detect if the timestamp option appears
more than once in a packet, to remove the option if the packet is
fragmented, etc. My previous change neglected to store the option
location when the router addresses were prespecified and Pointer >
Length. But now the option location is also stored when Flag is an
unrecognized value, to ensure these option handling behaviors are
still performed.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
New scheme calls for 3rd party VPD at offset 0x0 and Chelsio VPD at offset
0x400 of the function. If no 3rd party VPD is present, then a copy of
Chelsio's VPD will be at offset 0x0 to keep in line with PCI spec which
requires the VPD to be present at offset 0x0.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Merge sfc changes (only) accepted for 3.9.
2. PTP improvements from Laurence Evans.
3. Overhaul of RX buffer management:
- Always allocate pages, and enable scattering where possible
- Fit as many buffers as will fit into a page, rather than limiting to 2
- Introduce recycle rings to reduce the need for IOMMU mapping and
unmapping
4. PCI error recovery (AER and EEH) implementation.
5. Fix a bug in RX filter replacement.
6. Fix configuration with 1 RX queue in the PF and multiple RX queues in
VFs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
