At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 35d48903e9 (bonding: fix rx_handler locking) added a race
in bonding driver, reported by Steven Rostedt who did a very good
diagnosis :
<quoting Steven>
I'm currently debugging a crash in an old 3.0-rt kernel that one of our
customers is seeing. The bug happens with a stress test that loads and
unloads the bonding module in a loop (I don't know all the details as
I'm not the one that is directly interacting with the customer). But the
bug looks to be something that may still be present and possibly present
in mainline too. It will just be much harder to trigger it in mainline.
In -rt, interrupts are threads, and can schedule in and out just like
any other thread. Note, mainline now supports interrupt threads so this
may be easily reproducible in mainline as well. I don't have the ability
to tell the customer to try mainline or other kernels, so my hands are
somewhat tied to what I can do.
But according to a core dump, I tracked down that the eth irq thread
crashed in bond_handle_frame() here:
slave = bond_slave_get_rcu(skb->dev);
bond = slave->bond; <--- BUG
the slave returned was NULL and accessing slave->bond caused a NULL
pointer dereference.
Looking at the code that unregisters the handler:
void netdev_rx_handler_unregister(struct net_device *dev)
{
ASSERT_RTNL();
RCU_INIT_POINTER(dev->rx_handler, NULL);
RCU_INIT_POINTER(dev->rx_handler_data, NULL);
}
Which is basically:
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
And looking at __netif_receive_skb() we have:
rx_handler = rcu_dereference(skb->dev->rx_handler);
if (rx_handler) {
if (pt_prev) {
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = NULL;
}
switch (rx_handler(&skb)) {
My question to all of you is, what stops this interrupt from happening
while the bonding module is unloading? What happens if the interrupt
triggers and we have this:
CPU0 CPU1
---- ----
rx_handler = skb->dev->rx_handler
netdev_rx_handler_unregister() {
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
rx_handler()
bond_handle_frame() {
slave = skb->dev->rx_handler;
bond = slave->bond; <-- NULL pointer dereference!!!
What protection am I missing in the bond release handler that would
prevent the above from happening?
</quoting Steven>
We can fix bug this in two ways. First is adding a test in
bond_handle_frame() and others to check if rx_handler_data is NULL.
A second way is adding a synchronize_net() in
netdev_rx_handler_unregister() to make sure that a rcu protected reader
has the guarantee to see a non NULL rx_handler_data.
The second way is better as it avoids an extra test in fast path.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Paul E. McKenney <paulmck@us.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add myself to netxen_nic maintainers list
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we hold a max of sch->limit -1 number of packets instead of
sch->limit packets. Fix this off-by-one error.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.
There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'nf_reset' is called just prior calling 'netif_rx'.
No need to call it twice.
Reported-by: Igor Michailov <rgohita@gmail.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_tasklet is not percpu var, and percpu is percpu var, and
this_cpu_ptr(&info->cache->percpu->flush_tasklet)
is not equal to
&this_cpu_ptr(info->cache->percpu)->flush_tasklet
1f743b076(use this_cpu_ptr per-cpu helper) introduced this bug.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne's errata proposal (Errata ID: 3480) to RFC4291 has been
verified: http://www.rfc-editor.org/errata_search.php?eid=3480
We have to check for pkt_type and loopback flag because either the
packets are allowed to travel over the loopback interface (in which case
pkt_type is PACKET_HOST and IFF_LOOPBACK flag is set) or they travel
over a non-loopback interface back to us (in which case PACKET_TYPE is
PACKET_LOOPBACK and IFF_LOOPBACK flag is not set).
Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please excuse this larger-than-I-would-like pull request intended
for the 3.9 stream. There are a number of late-breaking fixes,
including a revert...
Regarding the mac80211 bits, Johannes says:
"I have two tracing fixes (one from Vladimir), two fixes for P2P device
crashes, a fix for a BSS memory leak/lost update problem and a fix from
Ben for a scanning issue in mac80211. It's a little on the large side
because one of the P2P device problems required a bit much locking work,
but I've run through all the different scenarios (wext/nl80211,
p2p-device/station interface, ifdown/rfkill) to verify locking with
lockdep."
As for the iwlwifi bits, Johannes says:
"I have three little fixes to the driver from Emmanuel. One addresses a
small bug Ben Hutchings found during the stable review process and two
address some warnings in the driver when RF-Kill is asserted."
Along with those...
Avinash Patil fixes an mwifiex bug cause by failing to process a sleep
command due to bad SKB manipulation when going into power saving mode.
Colin Ian King avoids a null pointer dereference in iwl4965.
Dan Williams officially announces that he has dropped maintainership
of the libertas driver.
Iestyn C. Elfick adds a work-around to avoid b43 DMA transmision
sequence error that would lead to a device reset.
Luis R. Rodriguez avoids an ath9k warning by not queueing a work item
while going to suspend mode.
Rafał Miłecki provides a pair of b43 N-PHY fixes related to RSSI
calibration.
Finally, I revert "brcmsmac: support 4313iPA" because it has been
reported in many places to cause problems with the already supported
4313ePA devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers use a non default hard_header_len
Transmitted skb should take into account dev->hard_header_len, or risk
crashes or expensive reallocations.
In the case of aoe, lets reserve MAX_HEADER bytes.
David reported a crash in defxx driver, solved by this patch.
Reported-by: David Oostdyk <daveo@ll.mit.edu>
Tested-by: David Oostdyk <daveo@ll.mit.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:
A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.
Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000, ixgb and e1000e for Christoph.
Christoph provides 3 patches to resolve missing dma_error_call's to
provided Intel drivers which did not have this fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Initialize the satype field in key_notify_policy_flush(),
this was left uninitialized. From Nicolas Dichtel.
2) The sequence number difference for replay notifications
was misscalculated on ESN sequence number wrap. We need
a separate replay notify function for esn.
3) Fix an off by one in the esn replay notify function.
From Mathias Krause.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 184b89044f ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling case
instead of 0(possible overwrite to 0 by ops->fill_xstats call),
as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch
1. boot with nfs (no_console_suspend)
2. echo mem >/sys/power/state
3. wakeup by wakesource
4. print "eth0: tx queue full"
This fix above problem by reinit bd queue at restart function
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some fixes which have collected since Linux v3.9-rc1. The most
important one fixes a long-standing regressen which make re-hotplugged
devices unusable when AMD IOMMU is used. The other patches fix build
issues (build regression on OMAP and a section mismatch). One patch just
removes a duplicate header include.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/K5U
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Here are some fixes which have collected since Linux v3.9-rc1.
The most important one fixes a long-standing regressen which make
re-hotplugged devices unusable when AMD IOMMU is used.
The other patches fix build issues (build regression on OMAP and a
section mismatch). One patch just removes a duplicate header include."
* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Make sure dma_ops are set for hotplug devices
x86, io_apic: remove duplicated include from irq_remapping.c
iommu: OMAP: build only on OMAP2+
amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround
Commit 06ae43f34b ("Don't bother with redoing rw_verify_area() from
default_file_splice_from()") lost the checks to test existence of the
write/aio_write methods. My apologies ;-/
Eventually, we want that in fs/splice.c side of things (no point
repeating it for every buffer, after all), but for now this is the
obvious minimal fix.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.
This code was introduced in e0c9a0219a
and caused stability regression on some cards, for ex. BCM4322.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Would be better maintained by somebody who actualy has time for it.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.
Smatch analysis:
drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following issue was reported.
WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40
Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.
This fixes a regression introduced in 3.4 by commit:
e0c9a0219a
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b6fc28a158.
This commit is reported to cause a regression in the support for some
revisions of 4313 ePA devices.
http://marc.info/?l=linux-wireless&m=136360340200943&w=2
Conflicts:
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch limits the PEAK PCAN-PC Card driver to systems with ioports. Fixes a
compile time breakage on SH:
drivers/net/can/sja1000/peak_pcmcia.c:626:2: error:
implicit declaration of function 'ioport_unmap'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:
drivers/net/can/sja1000/sja1000.h:59:0: warning:
"REG_SR" redefined [enabled by default]
arch/sh/include/asm/ptrace_32.h:25:0: note:
this is the location of the previous definition
A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After dma_map_page, dma_mapping_error must be called. It seems safe to
not free the skb/page allocated in this function, as the skb/page can be
reused later.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After dma_map_single, dma_mapping_error must be called. It seems safe to
not free the skb allocated in this function, as the skb can be reused
later.
Additionally this patch fixes one coding-style error.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After dma_map_single, dma_mapping_error must be called.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.
Cc: stable@vger.kernel.org
Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Pull vfs fixes from Al Viro:
"stable fodder; assorted deadlock fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vt: synchronize_rcu() under spinlock is not nice...
Nest rename_lock inside vfsmount_lock
Don't bother with redoing rw_verify_area() from default_file_splice_from()
vcs_poll_data_free() calls unregister_vt_notifier(), which calls
atomic_notifier_chain_unregister(), which calls synchronize_rcu().
Do it *after* we'd dropped ->f_lock.
Cc: stable@vger.kernel.org (all kernels since 2.6.37)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... lest we get livelocks between path_is_under() and d_path() and friends.
The thing is, wrt fairness lglocks are more similar to rwsems than to rwlocks;
it is possible to have thread B spin on attempt to take lock shared while thread
A is already holding it shared, if B is on lower-numbered CPU than A and there's
a thread C spinning on attempt to take the same lock exclusive.
As the result, we need consistent ordering between vfsmount_lock (lglock) and
rename_lock (seq_lock), even though everything that takes both is going to take
vfsmount_lock only shared.
Spotted-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking fixes from David Miller:
1) Always increment IPV4 ID field in encapsulated GSO packets, even
when DF is set. Regression fix from Pravin B Shelar.
2) Fix per-net subsystem initialization in netfilter conntrack,
otherwise we may access dynamically allocated memory before it is
actually allocated. From Gao Feng.
3) Fix DMA buffer lengths in iwl3945 driver, from Stanislaw Gruszka.
4) Fix race between submission of sync vs async commands in mwifiex
driver, from Amitkumar Karwar.
5) Add missing cancel of command timer in mwifiex driver, from Bing
Zhao.
6) Missing SKB free in rtlwifi USB driver, from Jussi Kivilinna.
7) Thermal layer tries to use a genetlink multicast string that is
longer than the 16 character limit. Fix it and add a BUG check to
prevent this kind of thing from happening in the future.
From Masatake YAMATO.
8) Fix many bugs in the handling of the teardown of L2TP connections,
UDP encapsulation instances, and sockets. From Tom Parkin.
9) Missing socket release in IRDA, from Kees Cook.
10) Fix fec driver modular build, from Fabio Estevam.
11) Erroneous use of kfree() instead of free_netdev() in lantiq_etop,
from Wei Yongjun.
12) Fix bugs in handling of queue numbers and steering rules in mlx4
driver, from Moshe Lazer, Hadar Hen Zion, and Or Gerlitz.
13) Some FOO_DIAG_MAX constants were defined off by one, fix from Andrey
Vagin.
14) TCP segmentation deferral is unintentionally done too strongly,
breaking ACK clocking. Fix from Eric Dumazet.
15) net_enable_timestamp() can legitimately be invoked from software
interrupts, and in a way that is safe, so remove the WARN_ON().
Also from Eric Dumazet.
16) Fix use after free in VLANs, from Cong Wang.
17) Fix TCP slow start retransmit storms after SACK reneging, from
Yuchung Cheng.
18) Unix socket release should mark a socket dead before NULL'ing out
sock->sk, otherwise we can race. Fix from Paul Moore.
19) IPV6 addrconf code can try to free static memory, from Hong Zhiguo.
20) Fix register mis-programming, NULL pointer derefs, and wrong PHC
clock frequency in IGB driver. From Lior LevyAlex Williamson, Jiri
Benc, and Jeff Kirsher.
21) skb->ip_summed logic in pch_gbe driver is reversed, breaking packet
forwarding. Fix from Veaceslav Falico.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
ipv4: Fix ip-header identification for gso packets.
bonding: remove already created master sysfs link on failure
af_unix: dont send SCM_CREDENTIAL when dest socket is NULL
pch_gbe: fix ip_summed checksum reporting on rx
igb: fix PHC stopping on max freq
igb: make sensor info static
igb: SR-IOV init reordering
igb: Fix null pointer dereference
igb: fix i350 anti spoofing config
ixgbevf: don't release the soft entries
ipv6: fix bad free of addrconf_init_net
unix: fix a race condition in unix_release()
tcp: undo spurious timeout after SACK reneging
bnx2x: fix assignment of signed expression to unsigned variable
bridge: fix crash when set mac address of br interface
8021q: fix a potential use-after-free
net: remove a WARN_ON() in net_enable_timestamp()
tcp: preserve ACK clocking in TSO
net: fix *_DIAG_MAX constants
net/mlx4_core: Disallow releasing VF QPs which have steering rules
...
- Fix an NFSv4 idmapper regression
- Fix an Oops in the pNFS blocks client
- Fix up various issues with pNFS layoutcommit
- Ensure correct read ordering of variables in rpc_wake_up_task_queue_locked
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRUedyAAoJEGcL54qWCgDyar0P/2pTT/yxX8ejTu5DmY7e4PYJ
jhPG2AEqY/yMLn9GvB375VIs1L8tuY50+3NFhWZFjyNbEU3GV+5Y+kPpBtAgYiSI
VyIXiJ/xMtXdYJMYuE/nh5jbcqJsHwGjpcIaSd5BuWzQUaoUYvLulxWd4QN8mmaT
5SuzmgV+7WIqV6RjlaYF82srcOKAjwemcrfRkCNzzJr6aT39gH2YdYFbDaTr7qhU
fw0x3QlI7887vSNQcfaGbC1+jr6oe8wRCneOR0tceU/8bcj6zlUDk5HxqSOc28mA
jUQieoVRggcM4s5DFpNcuwW6qCPZOmzv/OFD6oqnhyyonPOrue+7zaoujZmGNmjx
dT2V/jQehanYD25WpDO8OyFXUeYE4x9bgHKsszhBTwr4x5D8ceEJ1sugcOPiTTxu
tflbbuWbt+BguvXp4p8QayUj0V2cplM/nOovWyUG+BH46sz3Dtv46NOgJeO2a29g
T6jayxmKCxvtPKtG0j34BzLngiKabZTSEhFms6Qarp9lwWvHWrR9KWGuDBNvy1Ts
GMBN8P6Ib40yVi6Pwlj5Jpy6yLKVklHtJQpactr63AZmYrF4bBBSom+MWAh3X1iO
QtF0x9Z1bBkXY2Q/u+3vWMxQtEPeW+pSiloj8aiceFAt33zKM+1bLofDhEw0s2fI
wJEHYsGyGtDQINgP0v1e
=OPbZ
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix an NFSv4 idmapper regression
- Fix an Oops in the pNFS blocks client
- Fix up various issues with pNFS layoutcommit
- Ensure correct read ordering of variables in
rpc_wake_up_task_queue_locked
* tag 'nfs-for-3.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked
NFSv4.1: Add a helper pnfs_commit_and_return_layout
NFSv4.1: Always clear the NFS_INO_LAYOUTCOMMIT in layoutreturn
NFSv4.1: Fix a race in pNFS layoutcommit
pnfs-block: removing DM device maybe cause oops when call dev_remove
NFSv4: Fix the string length returned by the idmapper
Sergei Shtylyov