Code used by the non-__devinit s2io_open() mustn't be __devinit.
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x6f6e3e): Section mismatch: reference to .init.text.20:s2io_test_intr (between 's2io_open' and 's2io_ethtool_sset')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.init.text.20+0x4cb25): Section mismatch: reference to .exit.text:sis190_mii_remove (between 'sis190_init_one' and 'read_eeprom')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adapted from Ian Wienand <ianw@gelato.unsw.edu.au>
Explicitly free the IRQ before removing the device to remove a
warning "Destroying IRQ without calling free_irq"
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.
This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 70eba18b56, as per
Jeff Garzik:
"That was meant for 2.6.25, and actually (due to patching) applied to
a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Tue, 4 Dec 2007, Ingo Molnar wrote:
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_get_tuner_i2c_master'
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_set_config'
Seems like -common part contains also code that is not completely
common to all the modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch
drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is pretty serious bug. map->count is never initialized after the
call to kmalloc making the count start at some random trash value. The
end result is leaking videobufs.
Also, fix up the debug statements to print unsigned values.
Pushed to http://ifup.org/hg/v4l-dvb too
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux for composite over s-video input was wrong.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Complement va_start() with va_end() + minor style fixes in the same function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result. Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case
TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a modified version of a patch previously posted by Thomas
Unverzagt.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch is required so that the autodetecion code also works after
a reboot.
Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If we get an error during the actual policy lookup we don't free the
original dst while the caller expects us to always free the original
dst in case of error.
This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan module cleanup function starts with
vlan_netlink_fini();
vlan_ioctl_set(NULL);
The first call removes all the vlan devices and
the second one closes the vlan ioctl.
AFAIS there's a tiny race window between these two
calls - after rtnl unregistered all the vlans, but
the ioctl handler isn't set to NULL yet, user can
manage to call this ioctl and create one vlan device,
and that this function will later BUG_ON seeing
non-emply hashes.
I think, that we must first close the vlan ioctl
and only after this remove all the vlans with the
vlan_netlink_fini() call.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some return value comments for void functions.
Fixed it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. netif_rx_ni calls netif_rx, so the same problem occurs in
the files below.
I have left the updating of dev->last_rx after the calls to netif_rx_ni
because it seems time dependent, but moved the other field updates before.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Herbert, the ipv4_devconf_setall should be called
only when the ifa is added to the device. However, failed
ifa allocation may bring things into inconsistent state.
Move the call to ipv4_devconf_setall after the ifa allocation.
Fits both net-2.6 (with offsets) and net-2.6.25 (cleanly).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTCF_xxx flags, defined in include/linux/in_route.h) are available for
IPv4 route (rtable) entries only. Use RTF_xxx flags instead, defined
in include/linux/ipv6_route.h, for IPv6 route entries (rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>