In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller. This is required.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The effect of cache sync operation is to drain the store buffer and
wait for all internal buffers to be empty. In normal conditions, store
buffer is able to merge the normal memory writes within its 32-byte
data buffers. Due to this erratum present in r3p0, the effect of cache
sync operation on the store buffer still remains when the operation
completes. This means that the store buffer is always asked to drain
and this prevents it from merging any further writes.
This can severely affect performance on the write traffic esp. on
Normal memory NC one.
The proposed workaround is to replace the normal offset of cache sync
operation(0x730) by another offset targeting an unmapped PL310
register 0x740.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
The commit 6ac6b817f3 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:
CC arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1
Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds the PL310 Auxiliary Control Register bitfields
so that SOC's can use these bit fields to construct the AUXCTRL
value to be passed/programmed instead of hardcoding it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid adding nasty genirq-specific code to local timers to enable PPI
interrupts. Instead, provide a gic function to do this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt. Move this into the common GIC code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is the identical GIC demux implementation
merge V3. Instead of implementing same code over and
over simply share it in entry-macro-gic.S. The shared
code is based on the realview implementation.
Each GIC demux instance still has to setup the base address
of the controller using the get_irqnr_preamble macro. The
rest of the GIC specific code can be shared.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Rob Herring <rob.herring@smooth-stone.com>
The timer-sp h/w used on versatile platforms can also be used for other
platforms, so move it to a common location.
Signed-off-by: Rob Herring <rob.herring@smooth-stone.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cache size is needed for to optimise range based
maintainance operations
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Replace tab with space after #define to be consisten with other
define in the file. Also move the bit mask below the register offsets.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
This patch adds L2X0 Prefetch and Power control register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is done so as to be able to make use of the coresight components'
registers in assembler code (like omap sleep code). Also, there shouldn't
be any users of this structure outside the etm driver.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus/samsung-2635' of git://git.fluff.org/bjdooks/linux:
DMAENGINE: correct PL080 register header file
ARM: SAMSUNG: Fix on build warning about dependency in Kconfig
ARM: SMDK6410: Make virtual screen twice depth of real
ARM: S3C64XX: Update consistent DMA size to 8MiB
ARM: S3C64XX: Add audio support to SmartQ
ARM: S3C64XX: Framebuffer fix for SmartQ5
ARM: S3C64XX: Set wifi and iNAND as permanently connected SD devices on SmartQ boards
ARM: S3C64XX: Move SmartQ LCD control platform definition to shared file
ARM: mach-real6410: add sdhc device support
ARM: mach-real6410: add dm9000 ethernet support for mach-real6410
ARM: S3C64XX: Support for Real6410
Fix up trivial conflicts in arch/arm/mach-s3c64xx/mach-smartq5.c
("remove pixclock" vs "Framebuffer fix for SmartQ5")
This PL008 among all other variables named PL080 doesn't seem
right. Fix it. Also add some missing defined that I use in the
new PL08x driver.
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add bit definitions of the CPR register of the SCOOP chip into scoop.h. Also,
cleanup the GPCR definitions to match coding style.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PL330 is a configurable DMA controller PrimeCell device.
The register map of the device is well defined.
The configuration of a particular implementation can be
read from the six configuration registers CR0-4,Dn.
This patch implements a driver for the specification:-
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0424a/DDI0424A_dmac_pl330_r0p0_trm.pdf
The exported interface should be sufficient to implement
a driver for any DMA API.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L310 cache controller's interface is almost identical
to the L210. One major difference is that the PL310 can
have up to 16 ways.
This change uses the cache's part ID and the Associativity
bits in the AUX_CTRL register to determine the number of ways.
Also, this version prints out the CACHE_ID and AUX_CTRL registers.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only difference between ICST307 and ICST525 are the two arrays
for calculating the S parameter; the code is now identical. Merge
the two files and kill the duplicated code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the ICST support fit more nicely with the clk API,
eliminating the need to *1000 and /1000 in places.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These functions were originally implemented for the CLCD driver before
we had clk API support. Since the CLCD driver does not use these
anymore, we can remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The structures for the ICST307 and ICST525 VCO devices are
identical, so merge them together.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we reach the loop, len is at least 1, we only stay in the loop when
len is at least MAX_BYTE_COUNT + 1, MAX_BYTE_COUNT is subtracted in each
iteration. So when we leave the loop, or didn't take it, len is at least 1.
Testing whether len is non-zero appears redundant.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This driver implements support for on-chip Embedded Tracing Macrocell and
Embedded Trace Buffer. It allows to trigger tracing of kernel execution flow
and exporting trace output to userspace via character device and a sysrq
combo.
Trace output can then be decoded by a fairly simple open source tool [1]
which is already sufficient to get the idea of what the kernel is doing.
[1]: http://github.com/virtuoso/etm2human
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Tauros2 L2 cache controller as used with the PJ1
and PJ4 CPUs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
