linux/drivers/serial/pxa.c
Russell King b129a8ccd5 [SERIAL] Clean up and fix tty transmission start/stoping
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)

There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive.  In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.

There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.

Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-08-31 10:12:14 +01:00

866 lines
20 KiB
C

/*
* linux/drivers/serial/pxa.c
*
* Based on drivers/serial/8250.c by Russell King.
*
* Author: Nicolas Pitre
* Created: Feb 20, 2003
* Copyright: (C) 2003 Monta Vista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* Note 1: This driver is made separate from the already too overloaded
* 8250.c because it needs some kirks of its own and that'll make it
* easier to add DMA support.
*
* Note 2: I'm too sick of device allocation policies for serial ports.
* If someone else wants to request an "official" allocation of major/minor
* for this driver please be my guest. And don't forget that new hardware
* to come from Intel might have more than 3 or 4 of those UARTs. Let's
* hope for a better port registration and dynamic device allocation scheme
* with the serial core maintainer satisfaction to appear soon.
*/
#include <linux/config.h>
#if defined(CONFIG_SERIAL_PXA_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/serial_reg.h>
#include <linux/circ_buf.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <asm/io.h>
#include <asm/hardware.h>
#include <asm/irq.h>
#include <asm/arch/pxa-regs.h>
struct uart_pxa_port {
struct uart_port port;
unsigned char ier;
unsigned char lcr;
unsigned char mcr;
unsigned int lsr_break_flag;
unsigned int cken;
char *name;
};
static inline unsigned int serial_in(struct uart_pxa_port *up, int offset)
{
offset <<= 2;
return readl(up->port.membase + offset);
}
static inline void serial_out(struct uart_pxa_port *up, int offset, int value)
{
offset <<= 2;
writel(value, up->port.membase + offset);
}
static void serial_pxa_enable_ms(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
}
static void serial_pxa_stop_tx(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
if (up->ier & UART_IER_THRI) {
up->ier &= ~UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
}
static void serial_pxa_stop_rx(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
up->ier &= ~UART_IER_RLSI;
up->port.read_status_mask &= ~UART_LSR_DR;
serial_out(up, UART_IER, up->ier);
}
static inline void
receive_chars(struct uart_pxa_port *up, int *status, struct pt_regs *regs)
{
struct tty_struct *tty = up->port.info->tty;
unsigned int ch, flag;
int max_count = 256;
do {
if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
if (tty->low_latency)
tty_flip_buffer_push(tty);
/*
* If this failed then we will throw away the
* bytes but must do so to clear interrupts
*/
}
ch = serial_in(up, UART_RX);
flag = TTY_NORMAL;
up->port.icount.rx++;
if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
UART_LSR_FE | UART_LSR_OE))) {
/*
* For statistics only
*/
if (*status & UART_LSR_BI) {
*status &= ~(UART_LSR_FE | UART_LSR_PE);
up->port.icount.brk++;
/*
* We do the SysRQ and SAK checking
* here because otherwise the break
* may get masked by ignore_status_mask
* or read_status_mask.
*/
if (uart_handle_break(&up->port))
goto ignore_char;
} else if (*status & UART_LSR_PE)
up->port.icount.parity++;
else if (*status & UART_LSR_FE)
up->port.icount.frame++;
if (*status & UART_LSR_OE)
up->port.icount.overrun++;
/*
* Mask off conditions which should be ignored.
*/
*status &= up->port.read_status_mask;
#ifdef CONFIG_SERIAL_PXA_CONSOLE
if (up->port.line == up->port.cons->index) {
/* Recover the break flag from console xmit */
*status |= up->lsr_break_flag;
up->lsr_break_flag = 0;
}
#endif
if (*status & UART_LSR_BI) {
flag = TTY_BREAK;
} else if (*status & UART_LSR_PE)
flag = TTY_PARITY;
else if (*status & UART_LSR_FE)
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch, regs))
goto ignore_char;
uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag);
ignore_char:
*status = serial_in(up, UART_LSR);
} while ((*status & UART_LSR_DR) && (max_count-- > 0));
tty_flip_buffer_push(tty);
}
static void transmit_chars(struct uart_pxa_port *up)
{
struct circ_buf *xmit = &up->port.info->xmit;
int count;
if (up->port.x_char) {
serial_out(up, UART_TX, up->port.x_char);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
serial_pxa_stop_tx(&up->port);
return;
}
count = up->port.fifosize / 2;
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
if (uart_circ_empty(xmit))
serial_pxa_stop_tx(&up->port);
}
static void serial_pxa_start_tx(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
if (!(up->ier & UART_IER_THRI)) {
up->ier |= UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
}
static inline void check_modem_status(struct uart_pxa_port *up)
{
int status;
status = serial_in(up, UART_MSR);
if ((status & UART_MSR_ANY_DELTA) == 0)
return;
if (status & UART_MSR_TERI)
up->port.icount.rng++;
if (status & UART_MSR_DDSR)
up->port.icount.dsr++;
if (status & UART_MSR_DDCD)
uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
if (status & UART_MSR_DCTS)
uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
wake_up_interruptible(&up->port.info->delta_msr_wait);
}
/*
* This handles the interrupt from one port.
*/
static inline irqreturn_t
serial_pxa_irq(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)dev_id;
unsigned int iir, lsr;
iir = serial_in(up, UART_IIR);
if (iir & UART_IIR_NO_INT)
return IRQ_NONE;
lsr = serial_in(up, UART_LSR);
if (lsr & UART_LSR_DR)
receive_chars(up, &lsr, regs);
check_modem_status(up);
if (lsr & UART_LSR_THRE)
transmit_chars(up);
return IRQ_HANDLED;
}
static unsigned int serial_pxa_tx_empty(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
static unsigned int serial_pxa_get_mctrl(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char status;
unsigned int ret;
return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
status = serial_in(up, UART_MSR);
ret = 0;
if (status & UART_MSR_DCD)
ret |= TIOCM_CAR;
if (status & UART_MSR_RI)
ret |= TIOCM_RNG;
if (status & UART_MSR_DSR)
ret |= TIOCM_DSR;
if (status & UART_MSR_CTS)
ret |= TIOCM_CTS;
return ret;
}
static void serial_pxa_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char mcr = 0;
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
mcr |= up->mcr;
serial_out(up, UART_MCR, mcr);
}
static void serial_pxa_break_ctl(struct uart_port *port, int break_state)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
serial_out(up, UART_LCR, up->lcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
#if 0
static void serial_pxa_dma_init(struct pxa_uart *up)
{
up->rxdma =
pxa_request_dma(up->name, DMA_PRIO_LOW, pxa_receive_dma, up);
if (up->rxdma < 0)
goto out;
up->txdma =
pxa_request_dma(up->name, DMA_PRIO_LOW, pxa_transmit_dma, up);
if (up->txdma < 0)
goto err_txdma;
up->dmadesc = kmalloc(4 * sizeof(pxa_dma_desc), GFP_KERNEL);
if (!up->dmadesc)
goto err_alloc;
/* ... */
err_alloc:
pxa_free_dma(up->txdma);
err_rxdma:
pxa_free_dma(up->rxdma);
out:
return;
}
#endif
static int serial_pxa_startup(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
int retval;
up->mcr = 0;
/*
* Allocate the IRQ
*/
retval = request_irq(up->port.irq, serial_pxa_irq, 0, up->name, up);
if (retval)
return retval;
/*
* Clear the FIFO buffers and disable them.
* (they will be reenabled in set_termios())
*/
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_out(up, UART_FCR, 0);
/*
* Clear the interrupt registers.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
/*
* Now, initialize the UART
*/
serial_out(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl |= TIOCM_OUT2;
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occuring imminently
* anyway, so we don't enable them here.
*/
up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE | UART_IER_UUE;
serial_out(up, UART_IER, up->ier);
/*
* And clear the interrupt registers again for luck.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
return 0;
}
static void serial_pxa_shutdown(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
free_irq(up->port.irq, up);
/*
* Disable interrupts from this port
*/
up->ier = 0;
serial_out(up, UART_IER, 0);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl &= ~TIOCM_OUT2;
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Disable break condition and FIFOs
*/
serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT);
serial_out(up, UART_FCR, 0);
}
static void
serial_pxa_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR1;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR8;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Ensure the port will be enabled.
* This is required especially for serial console.
*/
up->ier |= IER_UUE;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, quot);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
serial_out(up, UART_FCR, fcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void
serial_pxa_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
pxa_set_cken(up->cken, !state);
if (!state)
udelay(1);
}
static void serial_pxa_release_port(struct uart_port *port)
{
}
static int serial_pxa_request_port(struct uart_port *port)
{
return 0;
}
static void serial_pxa_config_port(struct uart_port *port, int flags)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
up->port.type = PORT_PXA;
}
static int
serial_pxa_verify_port(struct uart_port *port, struct serial_struct *ser)
{
/* we don't want the core code to modify any port params */
return -EINVAL;
}
static const char *
serial_pxa_type(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
return up->name;
}
#ifdef CONFIG_SERIAL_PXA_CONSOLE
extern struct uart_pxa_port serial_pxa_ports[];
extern struct uart_driver serial_pxa_reg;
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/*
* Wait for transmitter & holding register to empty
*/
static inline void wait_for_xmitr(struct uart_pxa_port *up)
{
unsigned int status, tmout = 10000;
/* Wait up to 10ms for the character(s) to be sent. */
do {
status = serial_in(up, UART_LSR);
if (status & UART_LSR_BI)
up->lsr_break_flag = UART_LSR_BI;
if (--tmout == 0)
break;
udelay(1);
} while ((status & BOTH_EMPTY) != BOTH_EMPTY);
/* Wait up to 1s for flow control if necessary */
if (up->port.flags & UPF_CONS_FLOW) {
tmout = 1000000;
while (--tmout &&
((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
udelay(1);
}
}
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial_pxa_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_pxa_port *up = &serial_pxa_ports[co->index];
unsigned int ier;
int i;
/*
* First save the UER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, UART_IER_UUE);
/*
* Now, do each character
*/
for (i = 0; i < count; i++, s++) {
wait_for_xmitr(up);
/*
* Send the character out.
* If a LF, also do CR...
*/
serial_out(up, UART_TX, *s);
if (*s == 10) {
wait_for_xmitr(up);
serial_out(up, UART_TX, 13);
}
}
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
}
static int __init
serial_pxa_console_setup(struct console *co, char *options)
{
struct uart_pxa_port *up;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
if (co->index == -1 || co->index >= serial_pxa_reg.nr)
co->index = 0;
up = &serial_pxa_ports[co->index];
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
return uart_set_options(&up->port, co, baud, parity, bits, flow);
}
static struct console serial_pxa_console = {
.name = "ttyS",
.write = serial_pxa_console_write,
.device = uart_console_device,
.setup = serial_pxa_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &serial_pxa_reg,
};
static int __init
serial_pxa_console_init(void)
{
register_console(&serial_pxa_console);
return 0;
}
console_initcall(serial_pxa_console_init);
#define PXA_CONSOLE &serial_pxa_console
#else
#define PXA_CONSOLE NULL
#endif
struct uart_ops serial_pxa_pops = {
.tx_empty = serial_pxa_tx_empty,
.set_mctrl = serial_pxa_set_mctrl,
.get_mctrl = serial_pxa_get_mctrl,
.stop_tx = serial_pxa_stop_tx,
.start_tx = serial_pxa_start_tx,
.stop_rx = serial_pxa_stop_rx,
.enable_ms = serial_pxa_enable_ms,
.break_ctl = serial_pxa_break_ctl,
.startup = serial_pxa_startup,
.shutdown = serial_pxa_shutdown,
.set_termios = serial_pxa_set_termios,
.pm = serial_pxa_pm,
.type = serial_pxa_type,
.release_port = serial_pxa_release_port,
.request_port = serial_pxa_request_port,
.config_port = serial_pxa_config_port,
.verify_port = serial_pxa_verify_port,
};
static struct uart_pxa_port serial_pxa_ports[] = {
{ /* FFUART */
.name = "FFUART",
.cken = CKEN6_FFUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
.membase = (void *)&FFUART,
.mapbase = __PREG(FFUART),
.irq = IRQ_FFUART,
.uartclk = 921600 * 16,
.fifosize = 64,
.ops = &serial_pxa_pops,
.line = 0,
},
}, { /* BTUART */
.name = "BTUART",
.cken = CKEN7_BTUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
.membase = (void *)&BTUART,
.mapbase = __PREG(BTUART),
.irq = IRQ_BTUART,
.uartclk = 921600 * 16,
.fifosize = 64,
.ops = &serial_pxa_pops,
.line = 1,
},
}, { /* STUART */
.name = "STUART",
.cken = CKEN5_STUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
.membase = (void *)&STUART,
.mapbase = __PREG(STUART),
.irq = IRQ_STUART,
.uartclk = 921600 * 16,
.fifosize = 64,
.ops = &serial_pxa_pops,
.line = 2,
},
}
};
static struct uart_driver serial_pxa_reg = {
.owner = THIS_MODULE,
.driver_name = "PXA serial",
.devfs_name = "tts/",
.dev_name = "ttyS",
.major = TTY_MAJOR,
.minor = 64,
.nr = ARRAY_SIZE(serial_pxa_ports),
.cons = PXA_CONSOLE,
};
static int serial_pxa_suspend(struct device *_dev, pm_message_t state, u32 level)
{
struct uart_pxa_port *sport = dev_get_drvdata(_dev);
if (sport && level == SUSPEND_DISABLE)
uart_suspend_port(&serial_pxa_reg, &sport->port);
return 0;
}
static int serial_pxa_resume(struct device *_dev, u32 level)
{
struct uart_pxa_port *sport = dev_get_drvdata(_dev);
if (sport && level == RESUME_ENABLE)
uart_resume_port(&serial_pxa_reg, &sport->port);
return 0;
}
static int serial_pxa_probe(struct device *_dev)
{
struct platform_device *dev = to_platform_device(_dev);
serial_pxa_ports[dev->id].port.dev = _dev;
uart_add_one_port(&serial_pxa_reg, &serial_pxa_ports[dev->id].port);
dev_set_drvdata(_dev, &serial_pxa_ports[dev->id]);
return 0;
}
static int serial_pxa_remove(struct device *_dev)
{
struct uart_pxa_port *sport = dev_get_drvdata(_dev);
dev_set_drvdata(_dev, NULL);
if (sport)
uart_remove_one_port(&serial_pxa_reg, &sport->port);
return 0;
}
static struct device_driver serial_pxa_driver = {
.name = "pxa2xx-uart",
.bus = &platform_bus_type,
.probe = serial_pxa_probe,
.remove = serial_pxa_remove,
.suspend = serial_pxa_suspend,
.resume = serial_pxa_resume,
};
int __init serial_pxa_init(void)
{
int ret;
ret = uart_register_driver(&serial_pxa_reg);
if (ret != 0)
return ret;
ret = driver_register(&serial_pxa_driver);
if (ret != 0)
uart_unregister_driver(&serial_pxa_reg);
return ret;
}
void __exit serial_pxa_exit(void)
{
driver_unregister(&serial_pxa_driver);
uart_unregister_driver(&serial_pxa_reg);
}
module_init(serial_pxa_init);
module_exit(serial_pxa_exit);
MODULE_LICENSE("GPL");