linux/arch/arm/mach-h720x/h7202-eval.c
Nicolas Pitre 3746f02254 ARM: mach-h720x: convert boot_params to atag_offset
The value used for boot_params in h7201-eval.c is nonsensical, given that
PLAT_PHYS_OFFSET is defined to 0x40000000.  Left unchanged to purposely
break the build to get its maintainer's attention.

Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2011-08-21 17:14:50 -04:00

80 lines
2 KiB
C

/*
* linux/arch/arm/mach-h720x/h7202-eval.c
*
* Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
* 2003 Robert Schwebel <r.schwebel@pengutronix.de>
* 2004 Sascha Hauer <s.hauer@pengutronix.de>
*
* Architecture specific stuff for Hynix HMS30C7202 development board
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/platform_device.h>
#include <asm/setup.h>
#include <asm/types.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/mach/arch.h>
#include <mach/irqs.h>
#include <mach/hardware.h>
#include "common.h"
static struct resource cirrus_resources[] = {
[0] = {
.start = ETH0_PHYS + 0x300,
.end = ETH0_PHYS + 0x300 + 0x10,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_CHAINED_GPIOB(8),
.end = IRQ_CHAINED_GPIOB(8),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device cirrus_device = {
.name = "cirrus-cs89x0",
.id = -1,
.num_resources = ARRAY_SIZE(cirrus_resources),
.resource = cirrus_resources,
};
static struct platform_device *devices[] __initdata = {
&cirrus_device,
};
/*
* Hardware init. This is called early in initcalls
* Place pin inits here. So you avoid adding ugly
* #ifdef stuff to common drivers.
* Use this only, if your bootloader is not able
* to initialize the pins proper.
*/
static void __init init_eval_h7202(void)
{
init_hw_h7202();
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
/* Enable interrupt on portb bit 8 (ethernet) */
CPU_REG (GPIO_B_VIRT, GPIO_POL) &= ~(1 << 8);
CPU_REG (GPIO_B_VIRT, GPIO_EN) |= (1 << 8);
}
MACHINE_START(H7202, "Hynix HMS30C7202")
/* Maintainer: Robert Schwebel, Pengutronix */
.atag_offset = 0x100,
.map_io = h720x_map_io,
.init_irq = h7202_init_irq,
.timer = &h7202_timer,
.init_machine = init_eval_h7202,
.dma_zone_size = SZ_256M,
MACHINE_END