linux/arch/v850/kernel/rte_ma1_cb.c
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00

105 lines
2.9 KiB
C

/*
* arch/v850/kernel/rte_ma1_cb.c -- Midas labs RTE-V850E/MA1-CB board
*
* Copyright (C) 2001,02,03 NEC Electronics Corporation
* Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
*
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file COPYING in the main directory of this
* archive for more details.
*
* Written by Miles Bader <miles@gnu.org>
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/bootmem.h>
#include <asm/atomic.h>
#include <asm/page.h>
#include <asm/ma1.h>
#include <asm/rte_ma1_cb.h>
#include <asm/v850e_timer_c.h>
#include "mach.h"
/* SRAM and SDRAM are almost contiguous (with a small hole in between;
see mach_reserve_bootmem for details), so just use both as one big area. */
#define RAM_START SRAM_ADDR
#define RAM_END (SDRAM_ADDR + SDRAM_SIZE)
void __init mach_early_init (void)
{
rte_cb_early_init ();
}
void __init mach_get_physical_ram (unsigned long *ram_start,
unsigned long *ram_len)
{
*ram_start = RAM_START;
*ram_len = RAM_END - RAM_START;
}
void __init mach_reserve_bootmem ()
{
#ifdef CONFIG_RTE_CB_MULTI
/* Prevent the kernel from touching the monitor's scratch RAM. */
reserve_bootmem (MON_SCRATCH_ADDR, MON_SCRATCH_SIZE);
#endif
/* The space between SRAM and SDRAM is filled with duplicate
images of SRAM. Prevent the kernel from using them. */
reserve_bootmem (SRAM_ADDR + SRAM_SIZE,
SDRAM_ADDR - (SRAM_ADDR + SRAM_SIZE));
}
void mach_gettimeofday (struct timespec *tv)
{
tv->tv_sec = 0;
tv->tv_nsec = 0;
}
/* Called before configuring an on-chip UART. */
void rte_ma1_cb_uart_pre_configure (unsigned chan,
unsigned cflags, unsigned baud)
{
/* The RTE-MA1-CB connects some general-purpose I/O pins on the
CPU to the RTS/CTS lines of UART 0's serial connection.
I/O pins P42 and P43 are RTS and CTS respectively. */
if (chan == 0) {
/* Put P42 & P43 in I/O port mode. */
MA_PORT4_PMC &= ~0xC;
/* Make P42 an output, and P43 an input. */
MA_PORT4_PM = (MA_PORT4_PM & ~0xC) | 0x8;
}
/* Do pre-configuration for the actual UART. */
ma_uart_pre_configure (chan, cflags, baud);
}
void __init mach_init_irqs (void)
{
unsigned tc;
/* Initialize interrupts. */
ma_init_irqs ();
rte_cb_init_irqs ();
/* Use falling-edge-sensitivity for interrupts . */
V850E_TIMER_C_SESC (0) &= ~0xC;
V850E_TIMER_C_SESC (1) &= ~0xF;
/* INTP000-INTP011 are shared with `Timer C', so we have to set
up Timer C to pass them through as raw interrupts. */
for (tc = 0; tc < 2; tc++)
/* Turn on the timer. */
V850E_TIMER_C_TMCC0 (tc) |= V850E_TIMER_C_TMCC0_CAE;
/* Make sure the relevant port0/port1 pins are assigned
interrupt duty. We used INTP001-INTP011 (don't screw with
INTP000 because the monitor uses it). */
MA_PORT0_PMC |= 0x4; /* P02 (INTP001) in IRQ mode. */
MA_PORT1_PMC |= 0x6; /* P11 (INTP010) & P12 (INTP011) in IRQ mode.*/
}