ca45de77ad
Currently, the code to tear down BA sessions will execute after queues are stopped, but attempt to send frames, so those frames will just get queued, which isn't intended. Move this code to before to tear down the sessions properly. Additionally, after stopping queues, flush the TX queues in the driver driver to make sure all the frames went out. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
119 lines
2.8 KiB
C
119 lines
2.8 KiB
C
#include <net/mac80211.h>
|
|
#include <net/rtnetlink.h>
|
|
|
|
#include "ieee80211_i.h"
|
|
#include "mesh.h"
|
|
#include "driver-ops.h"
|
|
#include "led.h"
|
|
|
|
int __ieee80211_suspend(struct ieee80211_hw *hw)
|
|
{
|
|
struct ieee80211_local *local = hw_to_local(hw);
|
|
struct ieee80211_sub_if_data *sdata;
|
|
struct sta_info *sta;
|
|
|
|
ieee80211_scan_cancel(local);
|
|
|
|
if (hw->flags & IEEE80211_HW_AMPDU_AGGREGATION) {
|
|
mutex_lock(&local->sta_mtx);
|
|
list_for_each_entry(sta, &local->sta_list, list) {
|
|
set_sta_flags(sta, WLAN_STA_BLOCK_BA);
|
|
ieee80211_sta_tear_down_BA_sessions(sta, true);
|
|
}
|
|
mutex_unlock(&local->sta_mtx);
|
|
}
|
|
|
|
ieee80211_stop_queues_by_reason(hw,
|
|
IEEE80211_QUEUE_STOP_REASON_SUSPEND);
|
|
|
|
/* flush out all packets */
|
|
synchronize_net();
|
|
|
|
drv_flush(local, false);
|
|
|
|
local->quiescing = true;
|
|
/* make quiescing visible to timers everywhere */
|
|
mb();
|
|
|
|
flush_workqueue(local->workqueue);
|
|
|
|
/* Don't try to run timers while suspended. */
|
|
del_timer_sync(&local->sta_cleanup);
|
|
|
|
/*
|
|
* Note that this particular timer doesn't need to be
|
|
* restarted at resume.
|
|
*/
|
|
cancel_work_sync(&local->dynamic_ps_enable_work);
|
|
del_timer_sync(&local->dynamic_ps_timer);
|
|
|
|
/* disable keys */
|
|
list_for_each_entry(sdata, &local->interfaces, list)
|
|
ieee80211_disable_keys(sdata);
|
|
|
|
/* tear down aggregation sessions and remove STAs */
|
|
mutex_lock(&local->sta_mtx);
|
|
list_for_each_entry(sta, &local->sta_list, list) {
|
|
if (sta->uploaded) {
|
|
sdata = sta->sdata;
|
|
if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
|
|
sdata = container_of(sdata->bss,
|
|
struct ieee80211_sub_if_data,
|
|
u.ap);
|
|
|
|
drv_sta_remove(local, sdata, &sta->sta);
|
|
}
|
|
|
|
mesh_plink_quiesce(sta);
|
|
}
|
|
mutex_unlock(&local->sta_mtx);
|
|
|
|
/* remove all interfaces */
|
|
list_for_each_entry(sdata, &local->interfaces, list) {
|
|
cancel_work_sync(&sdata->work);
|
|
|
|
switch(sdata->vif.type) {
|
|
case NL80211_IFTYPE_STATION:
|
|
ieee80211_sta_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_ADHOC:
|
|
ieee80211_ibss_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_MESH_POINT:
|
|
ieee80211_mesh_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_AP_VLAN:
|
|
case NL80211_IFTYPE_MONITOR:
|
|
/* don't tell driver about this */
|
|
continue;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (!ieee80211_sdata_running(sdata))
|
|
continue;
|
|
|
|
/* disable beaconing */
|
|
ieee80211_bss_info_change_notify(sdata,
|
|
BSS_CHANGED_BEACON_ENABLED);
|
|
|
|
drv_remove_interface(local, &sdata->vif);
|
|
}
|
|
|
|
/* stop hardware - this must stop RX */
|
|
if (local->open_count)
|
|
ieee80211_stop_device(local);
|
|
|
|
local->suspended = true;
|
|
/* need suspended to be visible before quiescing is false */
|
|
barrier();
|
|
local->quiescing = false;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* __ieee80211_resume() is a static inline which just calls
|
|
* ieee80211_reconfig(), which is also needed for hardware
|
|
* hang/firmware failure/etc. recovery.
|
|
*/
|