linux/net/mac80211/pm.c
John W. Linville 85f72bc839 mac80211: only cancel software-based scans on suspend
Otherwise the hardware scan handler could access an invalid scan request
structure.  The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-01 16:12:28 -04:00

114 lines
2.7 KiB
C

#include <net/mac80211.h>
#include <net/rtnetlink.h>
#include "ieee80211_i.h"
#include "mesh.h"
#include "driver-ops.h"
#include "led.h"
int __ieee80211_suspend(struct ieee80211_hw *hw)
{
struct ieee80211_local *local = hw_to_local(hw);
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
if (unlikely(test_bit(SCAN_SW_SCANNING, &local->scanning)))
ieee80211_scan_cancel(local);
ieee80211_stop_queues_by_reason(hw,
IEEE80211_QUEUE_STOP_REASON_SUSPEND);
/* flush out all packets */
synchronize_net();
local->quiescing = true;
/* make quiescing visible to timers everywhere */
mb();
flush_workqueue(local->workqueue);
/* Don't try to run timers while suspended. */
del_timer_sync(&local->sta_cleanup);
/*
* Note that this particular timer doesn't need to be
* restarted at resume.
*/
cancel_work_sync(&local->dynamic_ps_enable_work);
del_timer_sync(&local->dynamic_ps_timer);
/* disable keys */
list_for_each_entry(sdata, &local->interfaces, list)
ieee80211_disable_keys(sdata);
/* tear down aggregation sessions and remove STAs */
mutex_lock(&local->sta_mtx);
list_for_each_entry(sta, &local->sta_list, list) {
if (hw->flags & IEEE80211_HW_AMPDU_AGGREGATION) {
set_sta_flags(sta, WLAN_STA_BLOCK_BA);
ieee80211_sta_tear_down_BA_sessions(sta);
}
if (sta->uploaded) {
sdata = sta->sdata;
if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
sdata = container_of(sdata->bss,
struct ieee80211_sub_if_data,
u.ap);
drv_sta_remove(local, sdata, &sta->sta);
}
mesh_plink_quiesce(sta);
}
mutex_unlock(&local->sta_mtx);
/* remove all interfaces */
list_for_each_entry(sdata, &local->interfaces, list) {
cancel_work_sync(&sdata->work);
switch(sdata->vif.type) {
case NL80211_IFTYPE_STATION:
ieee80211_sta_quiesce(sdata);
break;
case NL80211_IFTYPE_ADHOC:
ieee80211_ibss_quiesce(sdata);
break;
case NL80211_IFTYPE_MESH_POINT:
ieee80211_mesh_quiesce(sdata);
break;
case NL80211_IFTYPE_AP_VLAN:
case NL80211_IFTYPE_MONITOR:
/* don't tell driver about this */
continue;
default:
break;
}
if (!ieee80211_sdata_running(sdata))
continue;
/* disable beaconing */
ieee80211_bss_info_change_notify(sdata,
BSS_CHANGED_BEACON_ENABLED);
drv_remove_interface(local, &sdata->vif);
}
/* stop hardware - this must stop RX */
if (local->open_count)
ieee80211_stop_device(local);
local->suspended = true;
/* need suspended to be visible before quiescing is false */
barrier();
local->quiescing = false;
return 0;
}
/*
* __ieee80211_resume() is a static inline which just calls
* ieee80211_reconfig(), which is also needed for hardware
* hang/firmware failure/etc. recovery.
*/