linux/arch/arm/mach-omap2/hsmmc.c
Balaji T K 1fcecf281b ARM: OMAP4: MMC: increase delay for pbias
4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.

Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"

Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-06-01 04:48:15 -07:00

524 lines
14 KiB
C

/*
* linux/arch/arm/mach-omap2/hsmmc.c
*
* Copyright (C) 2007-2008 Texas Instruments
* Copyright (C) 2008 Nokia Corporation
* Author: Texas Instruments
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/delay.h>
#include <mach/hardware.h>
#include <plat/mmc.h>
#include <plat/omap-pm.h>
#include <plat/mux.h>
#include <plat/omap_device.h>
#include "mux.h"
#include "hsmmc.h"
#include "control.h"
#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
static u16 control_pbias_offset;
static u16 control_devconf1_offset;
static u16 control_mmc1;
#define HSMMC_NAME_LEN 9
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
static int hsmmc_get_context_loss(struct device *dev)
{
return omap_pm_get_dev_context_loss_count(dev);
}
#else
#define hsmmc_get_context_loss NULL
#endif
static void omap_hsmmc1_before_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
u32 reg, prog_io;
struct omap_mmc_platform_data *mmc = dev->platform_data;
if (mmc->slots[0].remux)
mmc->slots[0].remux(dev, slot, power_on);
/*
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
* card with Vcc regulator (from twl4030 or whatever). OMAP has both
* 1.8V and 3.0V modes, controlled by the PBIAS register.
*
* In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
* is most naturally TWL VSIM; those pins also use PBIAS.
*
* FIXME handle VMMC1A as needed ...
*/
if (power_on) {
if (cpu_is_omap2430()) {
reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
if ((1 << vdd) >= MMC_VDD_30_31)
reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE;
else
reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE;
omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
}
if (mmc->slots[0].internal_clock) {
reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
reg |= OMAP2_MMCSDIO1ADPCLKISEL;
omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0);
}
reg = omap_ctrl_readl(control_pbias_offset);
if (cpu_is_omap3630()) {
/* Set MMC I/O to 52Mhz */
prog_io = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
prog_io |= OMAP3630_PRG_SDMMC1_SPEEDCTRL;
omap_ctrl_writel(prog_io, OMAP343X_CONTROL_PROG_IO1);
} else {
reg |= OMAP2_PBIASSPEEDCTRL0;
}
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
omap_ctrl_writel(reg, control_pbias_offset);
} else {
reg = omap_ctrl_readl(control_pbias_offset);
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
omap_ctrl_writel(reg, control_pbias_offset);
}
}
static void omap_hsmmc1_after_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
u32 reg;
/* 100ms delay required for PBIAS configuration */
msleep(100);
if (power_on) {
reg = omap_ctrl_readl(control_pbias_offset);
reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0);
if ((1 << vdd) <= MMC_VDD_165_195)
reg &= ~OMAP2_PBIASLITEVMODE0;
else
reg |= OMAP2_PBIASLITEVMODE0;
omap_ctrl_writel(reg, control_pbias_offset);
} else {
reg = omap_ctrl_readl(control_pbias_offset);
reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 |
OMAP2_PBIASLITEVMODE0);
omap_ctrl_writel(reg, control_pbias_offset);
}
}
static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
u32 reg;
/*
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
* card with Vcc regulator (from twl4030 or whatever). OMAP has both
* 1.8V and 3.0V modes, controlled by the PBIAS register.
*
* In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
* is most naturally TWL VSIM; those pins also use PBIAS.
*
* FIXME handle VMMC1A as needed ...
*/
reg = omap4_ctrl_pad_readl(control_pbias_offset);
reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
OMAP4_MMC1_PWRDNZ_MASK |
OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
u32 reg;
unsigned long timeout;
if (power_on) {
reg = omap4_ctrl_pad_readl(control_pbias_offset);
reg |= OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK;
if ((1 << vdd) <= MMC_VDD_165_195)
reg &= ~OMAP4_MMC1_PBIASLITE_VMODE_MASK;
else
reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK;
reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
OMAP4_MMC1_PWRDNZ_MASK |
OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
timeout = jiffies + msecs_to_jiffies(5);
do {
reg = omap4_ctrl_pad_readl(control_pbias_offset);
if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
break;
usleep_range(100, 200);
} while (!time_after(jiffies, timeout));
if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
pr_err("Pbias Voltage is not same as LDO\n");
/* Caution : On VMODE_ERROR Power Down MMC IO */
reg &= ~(OMAP4_MMC1_PWRDNZ_MASK |
OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
} else {
reg = omap4_ctrl_pad_readl(control_pbias_offset);
reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
OMAP4_MMC1_PWRDNZ_MASK |
OMAP4_MMC1_PBIASLITE_VMODE_MASK |
OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
}
static void hsmmc23_before_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
struct omap_mmc_platform_data *mmc = dev->platform_data;
if (mmc->slots[0].remux)
mmc->slots[0].remux(dev, slot, power_on);
if (power_on) {
/* Only MMC2 supports a CLKIN */
if (mmc->slots[0].internal_clock) {
u32 reg;
reg = omap_ctrl_readl(control_devconf1_offset);
reg |= OMAP2_MMCSDIO2ADPCLKISEL;
omap_ctrl_writel(reg, control_devconf1_offset);
}
}
}
static int nop_mmc_set_power(struct device *dev, int slot, int power_on,
int vdd)
{
return 0;
}
static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller,
int controller_nr)
{
if ((mmc_controller->slots[0].switch_pin > 0) && \
(mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
OMAP_PIN_INPUT_PULLUP);
if ((mmc_controller->slots[0].gpio_wp > 0) && \
(mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
OMAP_PIN_INPUT_PULLUP);
if (cpu_is_omap34xx()) {
if (controller_nr == 0) {
omap_mux_init_signal("sdmmc1_clk",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_cmd",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat0",
OMAP_PIN_INPUT_PULLUP);
if (mmc_controller->slots[0].caps &
(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc1_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat2",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat3",
OMAP_PIN_INPUT_PULLUP);
}
if (mmc_controller->slots[0].caps &
MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc1_dat4",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat5",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat6",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat7",
OMAP_PIN_INPUT_PULLUP);
}
}
if (controller_nr == 1) {
/* MMC2 */
omap_mux_init_signal("sdmmc2_clk",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_cmd",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat0",
OMAP_PIN_INPUT_PULLUP);
/*
* For 8 wire configurations, Lines DAT4, 5, 6 and 7
* need to be muxed in the board-*.c files
*/
if (mmc_controller->slots[0].caps &
(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc2_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat2",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat3",
OMAP_PIN_INPUT_PULLUP);
}
if (mmc_controller->slots[0].caps &
MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat5.sdmmc2_dat5",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat6.sdmmc2_dat6",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat7.sdmmc2_dat7",
OMAP_PIN_INPUT_PULLUP);
}
}
/*
* For MMC3 the pins need to be muxed in the board-*.c files
*/
}
}
static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
struct omap_mmc_platform_data *mmc)
{
char *hc_name;
hc_name = kzalloc(sizeof(char) * (HSMMC_NAME_LEN + 1), GFP_KERNEL);
if (!hc_name) {
pr_err("Cannot allocate memory for controller slot name\n");
kfree(hc_name);
return -ENOMEM;
}
if (c->name)
strncpy(hc_name, c->name, HSMMC_NAME_LEN);
else
snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i",
c->mmc, 1);
mmc->slots[0].name = hc_name;
mmc->nr_slots = 1;
mmc->slots[0].caps = c->caps;
mmc->slots[0].internal_clock = !c->ext_clock;
mmc->dma_mask = 0xffffffff;
if (cpu_is_omap44xx())
mmc->reg_offset = OMAP4_MMC_REG_OFFSET;
else
mmc->reg_offset = 0;
mmc->get_context_loss_count = hsmmc_get_context_loss;
mmc->slots[0].switch_pin = c->gpio_cd;
mmc->slots[0].gpio_wp = c->gpio_wp;
mmc->slots[0].remux = c->remux;
mmc->slots[0].init_card = c->init_card;
if (c->cover_only)
mmc->slots[0].cover = 1;
if (c->nonremovable)
mmc->slots[0].nonremovable = 1;
if (c->power_saving)
mmc->slots[0].power_saving = 1;
if (c->no_off)
mmc->slots[0].no_off = 1;
if (c->no_off_init)
mmc->slots[0].no_regulator_off_init = c->no_off_init;
if (c->vcc_aux_disable_is_sleep)
mmc->slots[0].vcc_aux_disable_is_sleep = 1;
/*
* NOTE: MMC slots should have a Vcc regulator set up.
* This may be from a TWL4030-family chip, another
* controllable regulator, or a fixed supply.
*
* temporary HACK: ocr_mask instead of fixed supply
*/
mmc->slots[0].ocr_mask = c->ocr_mask;
if (cpu_is_omap3517() || cpu_is_omap3505())
mmc->slots[0].set_power = nop_mmc_set_power;
else
mmc->slots[0].features |= HSMMC_HAS_PBIAS;
if (cpu_is_omap44xx() && (omap_rev() > OMAP4430_REV_ES1_0))
mmc->slots[0].features |= HSMMC_HAS_UPDATED_RESET;
switch (c->mmc) {
case 1:
if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
/* on-chip level shifting via PBIAS0/PBIAS1 */
if (cpu_is_omap44xx()) {
mmc->slots[0].before_set_reg =
omap4_hsmmc1_before_set_reg;
mmc->slots[0].after_set_reg =
omap4_hsmmc1_after_set_reg;
} else {
mmc->slots[0].before_set_reg =
omap_hsmmc1_before_set_reg;
mmc->slots[0].after_set_reg =
omap_hsmmc1_after_set_reg;
}
}
/* OMAP3630 HSMMC1 supports only 4-bit */
if (cpu_is_omap3630() &&
(c->caps & MMC_CAP_8_BIT_DATA)) {
c->caps &= ~MMC_CAP_8_BIT_DATA;
c->caps |= MMC_CAP_4_BIT_DATA;
mmc->slots[0].caps = c->caps;
}
break;
case 2:
if (c->ext_clock)
c->transceiver = 1;
if (c->transceiver && (c->caps & MMC_CAP_8_BIT_DATA)) {
c->caps &= ~MMC_CAP_8_BIT_DATA;
c->caps |= MMC_CAP_4_BIT_DATA;
}
/* FALLTHROUGH */
case 3:
if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
/* off-chip level shifting, or none */
mmc->slots[0].before_set_reg = hsmmc23_before_set_reg;
mmc->slots[0].after_set_reg = NULL;
}
break;
case 4:
case 5:
mmc->slots[0].before_set_reg = NULL;
mmc->slots[0].after_set_reg = NULL;
break;
default:
pr_err("MMC%d configuration not supported!\n", c->mmc);
kfree(hc_name);
return -ENODEV;
}
return 0;
}
static struct omap_device_pm_latency omap_hsmmc_latency[] = {
[0] = {
.deactivate_func = omap_device_idle_hwmods,
.activate_func = omap_device_enable_hwmods,
.flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
},
/*
* XXX There should also be an entry here to power off/on the
* MMC regulators/PBIAS cells, etc.
*/
};
#define MAX_OMAP_MMC_HWMOD_NAME_LEN 16
void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr)
{
struct omap_hwmod *oh;
struct omap_device *od;
struct omap_device_pm_latency *ohl;
char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN];
struct omap_mmc_platform_data *mmc_data;
struct omap_mmc_dev_attr *mmc_dev_attr;
char *name;
int l;
int ohl_cnt = 0;
mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
if (!mmc_data) {
pr_err("Cannot allocate memory for mmc device!\n");
goto done;
}
if (omap_hsmmc_pdata_init(hsmmcinfo, mmc_data) < 0) {
pr_err("%s fails!\n", __func__);
goto done;
}
omap_hsmmc_mux(mmc_data, (ctrl_nr - 1));
name = "omap_hsmmc";
ohl = omap_hsmmc_latency;
ohl_cnt = ARRAY_SIZE(omap_hsmmc_latency);
l = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
"mmc%d", ctrl_nr);
WARN(l >= MAX_OMAP_MMC_HWMOD_NAME_LEN,
"String buffer overflow in MMC%d device setup\n", ctrl_nr);
oh = omap_hwmod_lookup(oh_name);
if (!oh) {
pr_err("Could not look up %s\n", oh_name);
kfree(mmc_data->slots[0].name);
goto done;
}
if (oh->dev_attr != NULL) {
mmc_dev_attr = oh->dev_attr;
mmc_data->controller_flags = mmc_dev_attr->flags;
}
od = omap_device_build(name, ctrl_nr - 1, oh, mmc_data,
sizeof(struct omap_mmc_platform_data), ohl, ohl_cnt, false);
if (IS_ERR(od)) {
WARN(1, "Can't build omap_device for %s:%s.\n", name, oh->name);
kfree(mmc_data->slots[0].name);
goto done;
}
/*
* return device handle to board setup code
* required to populate for regulator framework structure
*/
hsmmcinfo->dev = &od->pdev.dev;
done:
kfree(mmc_data);
}
void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
{
u32 reg;
if (!cpu_is_omap44xx()) {
if (cpu_is_omap2430()) {
control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE;
control_devconf1_offset = OMAP243X_CONTROL_DEVCONF1;
} else {
control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
control_devconf1_offset = OMAP343X_CONTROL_DEVCONF1;
}
} else {
control_pbias_offset =
OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_PBIASLITE;
control_mmc1 = OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_MMC1;
reg = omap4_ctrl_pad_readl(control_mmc1);
reg |= (OMAP4_SDMMC1_PUSTRENGTH_GRP0_MASK |
OMAP4_SDMMC1_PUSTRENGTH_GRP1_MASK);
reg &= ~(OMAP4_SDMMC1_PUSTRENGTH_GRP2_MASK |
OMAP4_SDMMC1_PUSTRENGTH_GRP3_MASK);
reg |= (OMAP4_USBC1_DR0_SPEEDCTRL_MASK|
OMAP4_SDMMC1_DR1_SPEEDCTRL_MASK |
OMAP4_SDMMC1_DR2_SPEEDCTRL_MASK);
omap4_ctrl_pad_writel(reg, control_mmc1);
}
for (; controllers->mmc; controllers++)
omap_init_hsmmc(controllers, controllers->mmc);
}
#endif