linux/drivers/ata/pata_ninja32.c

180 lines
4.6 KiB
C

/*
* pata_ninja32.c - Ninja32 PATA for new ATA layer
* (C) 2007 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* Note: The controller like many controllers has shared timings for
* PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
* in the dma_stop function. Thus we actually don't need a set_dmamode
* method as the PIO method is always called and will set the right PIO
* timing parameters.
*
* The Ninja32 Cardbus is not a generic SFF controller. Instead it is
* laid out as follows off BAR 0. This is based upon Mark Lord's delkin
* driver and the extensive analysis done by the BSD developers, notably
* ITOH Yasufumi.
*
* Base + 0x00 IRQ Status
* Base + 0x01 IRQ control
* Base + 0x02 Chipset control
* Base + 0x03 Unknown
* Base + 0x04 VDMA and reset control + wait bits
* Base + 0x08 BMIMBA
* Base + 0x0C DMA Length
* Base + 0x10 Taskfile
* Base + 0x18 BMDMA Status ?
* Base + 0x1C
* Base + 0x1D Bus master control
* bit 0 = enable
* bit 1 = 0 write/1 read
* bit 2 = 1 sgtable
* bit 3 = go
* bit 4-6 wait bits
* bit 7 = done
* Base + 0x1E AltStatus
* Base + 0x1F timing register
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_ninja32"
#define DRV_VERSION "0.0.1"
/**
* ninja32_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. Our timing registers are shared
* but we want to set the PIO timing by default.
*/
static void ninja32_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
static u16 pio_timing[5] = {
0xd6, 0x85, 0x44, 0x33, 0x13
};
iowrite8(pio_timing[adev->pio_mode - XFER_PIO_0],
ap->ioaddr.bmdma_addr + 0x1f);
ap->private_data = adev;
}
static void ninja32_dev_select(struct ata_port *ap, unsigned int device)
{
struct ata_device *adev = &ap->link.device[device];
if (ap->private_data != adev) {
iowrite8(0xd6, ap->ioaddr.bmdma_addr + 0x1f);
ata_sff_dev_select(ap, device);
ninja32_set_piomode(ap, adev);
}
}
static struct scsi_host_template ninja32_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations ninja32_port_ops = {
.inherits = &ata_bmdma_port_ops,
.sff_dev_select = ninja32_dev_select,
.cable_detect = ata_cable_40wire,
.set_piomode = ninja32_set_piomode,
};
static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ata_host *host;
struct ata_port *ap;
void __iomem *base;
int rc;
host = ata_host_alloc(&dev->dev, 1);
if (!host)
return -ENOMEM;
ap = host->ports[0];
/* Set up the PCI device */
rc = pcim_enable_device(dev);
if (rc)
return rc;
rc = pcim_iomap_regions(dev, 1 << 0, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(dev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(dev);
rc = pci_set_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
pci_set_master(dev);
/* Set up the register mappings */
base = host->iomap[0];
if (!base)
return -ENOMEM;
ap->ops = &ninja32_port_ops;
ap->pio_mask = 0x1F;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = base + 0x10;
ap->ioaddr.ctl_addr = base + 0x1E;
ap->ioaddr.altstatus_addr = base + 0x1E;
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */
iowrite8(0x01, base + 0x03); /* Unknown */
iowrite8(0x20, base + 0x04); /* WAIT0 */
iowrite8(0x8f, base + 0x05); /* Unknown */
iowrite8(0xa4, base + 0x1c); /* Unknown */
iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */
/* FIXME: Should we disable them at remove ? */
return ata_host_activate(host, dev->irq, ata_sff_interrupt,
IRQF_SHARED, &ninja32_sht);
}
static const struct pci_device_id ninja32[] = {
{ 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ },
};
static struct pci_driver ninja32_pci_driver = {
.name = DRV_NAME,
.id_table = ninja32,
.probe = ninja32_init_one,
.remove = ata_pci_remove_one
};
static int __init ninja32_init(void)
{
return pci_register_driver(&ninja32_pci_driver);
}
static void __exit ninja32_exit(void)
{
pci_unregister_driver(&ninja32_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Ninja32 ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ninja32);
MODULE_VERSION(DRV_VERSION);
module_init(ninja32_init);
module_exit(ninja32_exit);