linux/drivers/spi/Makefile
Cliff Cai 9c3e737561 spi/spi_bfin_sport: new driver for a SPI bus via the Blackfin SPORT peripheral
The Blackfin SPORT peripheral is a pretty flexible device.  With enough
coaching, we can make it generate SPI compatible waveforms.  This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA.  It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-27 01:23:54 -06:00

74 lines
2.7 KiB
Makefile

#
# Makefile for kernel SPI drivers.
#
ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
# small core, mostly translating board-specific
# config declarations into driver model code
obj-$(CONFIG_SPI_MASTER) += spi.o
# SPI master controller drivers (bus)
obj-$(CONFIG_SPI_ALTERA) += spi_altera.o
obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
obj-$(CONFIG_SPI_ATH79) += ath79_spi.o
obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BFIN_SPORT) += spi_bfin_sport.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_COLDFIRE_QSPI) += coldfire_qspi.o
obj-$(CONFIG_SPI_DAVINCI) += davinci_spi.o
obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o
obj-$(CONFIG_SPI_DW_PCI) += dw_spi_midpci.o
dw_spi_midpci-objs := dw_spi_pci.o dw_spi_mid.o
obj-$(CONFIG_SPI_DW_MMIO) += dw_spi_mmio.o
obj-$(CONFIG_SPI_EP93XX) += ep93xx_spi.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_PXA2XX_PCI) += pxa2xx_spi_pci.o
obj-$(CONFIG_SPI_OC_TINY) += spi_oc_tiny.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
obj-$(CONFIG_SPI_OMAP_100K) += omap_spi_100k.o
obj-$(CONFIG_SPI_ORION) += orion_spi.o
obj-$(CONFIG_SPI_PL022) += amba-pl022.o
obj-$(CONFIG_SPI_MPC512x_PSC) += mpc512x_psc_spi.o
obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o
obj-$(CONFIG_SPI_FSL_LIB) += spi_fsl_lib.o
obj-$(CONFIG_SPI_FSL_ESPI) += spi_fsl_espi.o
obj-$(CONFIG_SPI_FSL_SPI) += spi_fsl_spi.o
obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
obj-$(CONFIG_SPI_TEGRA) += spi_tegra.o
obj-$(CONFIG_SPI_TI_SSP) += ti-ssp-spi.o
obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi_topcliff_pch.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_SH) += spi_sh.o
obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
# special build for s3c24xx spi driver with fiq support
spi_s3c24xx_hw-y := spi_s3c24xx.o
spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
obj-$(CONFIG_SPI_SPIDEV) += spidev.o
obj-$(CONFIG_SPI_TLE62X0) += tle62x0.o
# ... add above this line ...
# SPI slave controller drivers (upstream link)
# ... add above this line ...
# SPI slave drivers (protocol for that link)
# ... add above this line ...