e036eaa681
This patch makes sure ctrl_inN/outN are used instead of inN/outN for on chip pci registers. Without this patch addresses may be adjusted using the value in generic_io_base. This patch makes it possible to set generic_io_base and have pci without reading and writing all over the place. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Katsuya MATSUBARA <matsu@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
162 lines
4.7 KiB
C
162 lines
4.7 KiB
C
/*
|
|
* Low-Level PCI Support for the SH7780
|
|
*
|
|
* Dustin McIntire (dustin@sensoria.com)
|
|
* Derived from arch/i386/kernel/pci-*.c which bore the message:
|
|
* (c) 1999--2000 Martin Mares <mj@ucw.cz>
|
|
*
|
|
* Ported to the new API by Paul Mundt <lethal@linux-sh.org>
|
|
* With cleanup by Paul van Gool <pvangool@mimotech.com>
|
|
*
|
|
* May be copied or modified under the terms of the GNU General Public
|
|
* License. See linux/COPYING for more information.
|
|
*
|
|
*/
|
|
#undef DEBUG
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/delay.h>
|
|
#include "pci-sh4.h"
|
|
|
|
#define INTC_BASE 0xffd00000
|
|
#define INTC_ICR0 (INTC_BASE+0x0)
|
|
#define INTC_ICR1 (INTC_BASE+0x1c)
|
|
#define INTC_INTPRI (INTC_BASE+0x10)
|
|
#define INTC_INTREQ (INTC_BASE+0x24)
|
|
#define INTC_INTMSK0 (INTC_BASE+0x44)
|
|
#define INTC_INTMSK1 (INTC_BASE+0x48)
|
|
#define INTC_INTMSK2 (INTC_BASE+0x40080)
|
|
#define INTC_INTMSKCLR0 (INTC_BASE+0x64)
|
|
#define INTC_INTMSKCLR1 (INTC_BASE+0x68)
|
|
#define INTC_INTMSKCLR2 (INTC_BASE+0x40084)
|
|
#define INTC_INT2MSKR (INTC_BASE+0x40038)
|
|
#define INTC_INT2MSKCR (INTC_BASE+0x4003c)
|
|
|
|
/*
|
|
* Initialization. Try all known PCI access methods. Note that we support
|
|
* using both PCI BIOS and direct access: in such cases, we use I/O ports
|
|
* to access config space.
|
|
*
|
|
* Note that the platform specific initialization (BSC registers, and memory
|
|
* space mapping) will be called via the platform defined function
|
|
* pcibios_init_platform().
|
|
*/
|
|
static int __init sh7780_pci_init(void)
|
|
{
|
|
unsigned int id;
|
|
int ret, match = 0;
|
|
|
|
pr_debug("PCI: Starting intialization.\n");
|
|
|
|
ctrl_outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */
|
|
|
|
/* check for SH7780/SH7780R hardware */
|
|
id = pci_read_reg(SH7780_PCIVID);
|
|
if ((id & 0xffff) == SH7780_VENDOR_ID) {
|
|
switch ((id >> 16) & 0xffff) {
|
|
case SH7763_DEVICE_ID:
|
|
case SH7780_DEVICE_ID:
|
|
case SH7781_DEVICE_ID:
|
|
case SH7785_DEVICE_ID:
|
|
match = 1;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (unlikely(!match)) {
|
|
printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id);
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* Setup the INTC */
|
|
if (mach_is_7780se()) {
|
|
/* ICR0: IRL=use separately */
|
|
ctrl_outl(0x00C00020, INTC_ICR0);
|
|
/* ICR1: detect low level(for 2ndcut) */
|
|
ctrl_outl(0xAAAA0000, INTC_ICR1);
|
|
/* INTPRI: priority=3(all) */
|
|
ctrl_outl(0x33333333, INTC_INTPRI);
|
|
}
|
|
|
|
if ((ret = sh4_pci_check_direct()) != 0)
|
|
return ret;
|
|
|
|
return pcibios_init_platform();
|
|
}
|
|
core_initcall(sh7780_pci_init);
|
|
|
|
int __init sh7780_pcic_init(struct sh4_pci_address_map *map)
|
|
{
|
|
u32 word;
|
|
|
|
/*
|
|
* This code is unused for some boards as it is done in the
|
|
* bootloader and doing it here means the MAC addresses loaded
|
|
* by the bootloader get lost.
|
|
*/
|
|
if (!(map->flags & SH4_PCIC_NO_RESET)) {
|
|
/* toggle PCI reset pin */
|
|
word = SH4_PCICR_PREFIX | SH4_PCICR_PRST;
|
|
pci_write_reg(word, SH4_PCICR);
|
|
/* Wait for a long time... not 1 sec. but long enough */
|
|
mdelay(100);
|
|
word = SH4_PCICR_PREFIX;
|
|
pci_write_reg(word, SH4_PCICR);
|
|
}
|
|
|
|
/* set the command/status bits to:
|
|
* Wait Cycle Control + Parity Enable + Bus Master +
|
|
* Mem space enable
|
|
*/
|
|
pci_write_reg(0x00000046, SH7780_PCICMD);
|
|
|
|
/* define this host as the host bridge */
|
|
word = PCI_BASE_CLASS_BRIDGE << 24;
|
|
pci_write_reg(word, SH7780_PCIRID);
|
|
|
|
/* Set IO and Mem windows to local address
|
|
* Make PCI and local address the same for easy 1 to 1 mapping
|
|
* Window0 = map->window0.size @ non-cached area base = SDRAM
|
|
* Window1 = map->window1.size @ cached area base = SDRAM
|
|
*/
|
|
word = ((map->window0.size - 1) & 0x1ff00001) | 0x01;
|
|
pci_write_reg(0x07f00001, SH4_PCILSR0);
|
|
word = ((map->window1.size - 1) & 0x1ff00001) | 0x01;
|
|
pci_write_reg(0x00000001, SH4_PCILSR1);
|
|
/* Set the values on window 0 PCI config registers */
|
|
word = P2SEGADDR(map->window0.base);
|
|
pci_write_reg(0xa8000000, SH4_PCILAR0);
|
|
pci_write_reg(0x08000000, SH7780_PCIMBAR0);
|
|
/* Set the values on window 1 PCI config registers */
|
|
word = P2SEGADDR(map->window1.base);
|
|
pci_write_reg(0x00000000, SH4_PCILAR1);
|
|
pci_write_reg(0x00000000, SH7780_PCIMBAR1);
|
|
|
|
/* Map IO space into PCI IO window
|
|
* The IO window is 64K-PCIBIOS_MIN_IO in size
|
|
* IO addresses will be translated to the
|
|
* PCI IO window base address
|
|
*/
|
|
pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n",
|
|
PCIBIOS_MIN_IO, (64 << 10),
|
|
SH7780_PCI_IO_BASE + PCIBIOS_MIN_IO);
|
|
|
|
/* NOTE: I'm ignoring the PCI error IRQs for now..
|
|
* TODO: add support for the internal error interrupts and
|
|
* DMA interrupts...
|
|
*/
|
|
|
|
/* Apply any last-minute PCIC fixups */
|
|
pci_fixup_pcic();
|
|
|
|
/* SH7780 init done, set central function init complete */
|
|
/* use round robin mode to stop a device starving/overruning */
|
|
word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_FTO;
|
|
pci_write_reg(word, SH4_PCICR);
|
|
|
|
return 1;
|
|
}
|