a57c1dcb93
While having tda18271 module set with debug=17 (cal & info prints) and cal=0 (delay calibration process until first use) - I discovered that during the calibration process, if the frequency test for 69750000 returned a bcal of 0 (see tda18721-fe.c in tda18271_powerscan func) that the tuner wouldn't be able to pickup any of the frequencies in the range (all the other frequencies bands returned bcal=1). I spent some time going over the code and the NXP's tda18271 spec (ver.4 of it i think) and adding a lot of debug prints and walking/stepping through the calibration process. I found that when the powerscan fails to find a frequency, the rf calibration is not run and the default value is supposed to be used in its place (pulled from the RF_CAL_map table) - but something was getting goofed up there. Now, my c coding skills are very rusty, but i think root of the problem is a signedness issue with the math operation for calculating the rf_a1 and rf_a2 values in tda18271_rf_tracking_filters_init func, which results in values like 20648 for rf_a1 (when it should probably have a value like 0, or so slightly negative that it should be zero - this bad value for rf_a1 would in turn makes the approx calc within tda18271c2_rf_tracking_filters_correction go out of whack). The simplest solution i found was to explicitly convert the signedness of the denominator to avoid the implicit conversion. The values placed into the u32 rf_freq array should never exceed about 900mhz, so i think the s32 max value shouldn't be an issue in this case. I've tested it out a little, and even when i get a bcal=0 with the modified code, the default calibration value gets used, rf_a1 is zero, and the tuner seems to lock on the stream and mythtv seems to play it fine. Signed-off-by: Seth Barry <seth@cyberseth.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> CC: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> |
||
---|---|---|
.. | ||
accessibility | ||
acpi | ||
amba | ||
ata | ||
atm | ||
auxdisplay | ||
base | ||
block | ||
bluetooth | ||
cdrom | ||
char | ||
clocksource | ||
connector | ||
cpufreq | ||
cpuidle | ||
crypto | ||
dca | ||
dio | ||
dma | ||
edac | ||
eisa | ||
firewire | ||
firmware | ||
gpio | ||
gpu | ||
hid | ||
hwmon | ||
i2c | ||
ide | ||
idle | ||
ieee1394 | ||
ieee802154 | ||
infiniband | ||
input | ||
isdn | ||
leds | ||
lguest | ||
macintosh | ||
mca | ||
md | ||
media | ||
memstick | ||
message | ||
mfd | ||
misc | ||
mmc | ||
mtd | ||
net | ||
nubus | ||
of | ||
oprofile | ||
parisc | ||
parport | ||
pci | ||
pcmcia | ||
platform | ||
pnp | ||
power | ||
pps | ||
ps3 | ||
rapidio | ||
regulator | ||
rtc | ||
s390 | ||
sbus | ||
scsi | ||
serial | ||
sfi | ||
sh | ||
sn | ||
spi | ||
ssb | ||
staging | ||
tc | ||
telephony | ||
thermal | ||
uio | ||
usb | ||
uwb | ||
video | ||
virtio | ||
vlynq | ||
w1 | ||
watchdog | ||
xen | ||
zorro | ||
Kconfig | ||
Makefile |