linux/net/Kconfig
Lennert Buytenhek 91da11f870 net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips.  It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.

The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:

	+-----------+       +-----------+
	|           | RGMII |           |
	|           +-------+           +------ 1000baseT MDI ("WAN")
	|           |       |  6-port   +------ 1000baseT MDI ("LAN1")
	|    CPU    |       |  ethernet +------ 1000baseT MDI ("LAN2")
	|           |MIImgmt|  switch   +------ 1000baseT MDI ("LAN3")
	|           +-------+  w/5 PHYs +------ 1000baseT MDI ("LAN4")
	|           |       |           |
	+-----------+       +-----------+

The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.

This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.

(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one.  The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 17:15:19 -07:00

257 lines
8.6 KiB
Text

#
# Network configuration
#
menuconfig NET
bool "Networking support"
---help---
Unless you really know what you are doing, you should say Y here.
The reason is that some programs need kernel networking support even
when running on a stand-alone machine that isn't connected to any
other computer.
If you are upgrading from an older kernel, you
should consider updating your networking tools too because changes
in the kernel and the tools often go hand in hand. The tools are
contained in the package net-tools, the location and version number
of which are given in <file:Documentation/Changes>.
For a general introduction to Linux networking, it is highly
recommended to read the NET-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
if NET
menu "Networking options"
config NET_NS
bool "Network namespace support"
default n
depends on EXPERIMENTAL && !SYSFS && NAMESPACES
help
Allow user space to create what appear to be multiple instances
of the network stack.
source "net/packet/Kconfig"
source "net/unix/Kconfig"
source "net/xfrm/Kconfig"
source "net/iucv/Kconfig"
config INET
bool "TCP/IP networking"
---help---
These are the protocols used on the Internet and on most local
Ethernets. It is highly recommended to say Y here (this will enlarge
your kernel by about 400 KB), since some programs (e.g. the X window
system) use TCP/IP even if your machine is not connected to any
other computer. You will get the so-called loopback device which
allows you to ping yourself (great fun, that!).
For an excellent introduction to Linux networking, please read the
Linux Networking HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
If you say Y here and also to "/proc file system support" and
"Sysctl support" below, you can change various aspects of the
behavior of the TCP/IP code by writing to the (virtual) files in
/proc/sys/net/ipv4/*; the options are explained in the file
<file:Documentation/networking/ip-sysctl.txt>.
Short answer: say Y.
if INET
source "net/ipv4/Kconfig"
source "net/ipv6/Kconfig"
source "net/netlabel/Kconfig"
endif # if INET
config NETWORK_SECMARK
bool "Security Marking"
help
This enables security marking of network packets, similar
to nfmark, but designated for security purposes.
If you are unsure how to answer this question, answer N.
menuconfig NETFILTER
bool "Network packet filtering framework (Netfilter)"
---help---
Netfilter is a framework for filtering and mangling network packets
that pass through your Linux box.
The most common use of packet filtering is to run your Linux box as
a firewall protecting a local network from the Internet. The type of
firewall provided by this kernel support is called a "packet
filter", which means that it can reject individual network packets
based on type, source, destination etc. The other kind of firewall,
a "proxy-based" one, is more secure but more intrusive and more
bothersome to set up; it inspects the network traffic much more
closely, modifies it and has knowledge about the higher level
protocols, which a packet filter lacks. Moreover, proxy-based
firewalls often require changes to the programs running on the local
clients. Proxy-based firewalls don't need support by the kernel, but
they are often combined with a packet filter, which only works if
you say Y here.
You should also say Y here if you intend to use your Linux box as
the gateway to the Internet for a local network of machines without
globally valid IP addresses. This is called "masquerading": if one
of the computers on your local network wants to send something to
the outside, your box can "masquerade" as that computer, i.e. it
forwards the traffic to the intended outside destination, but
modifies the packets to make it look like they came from the
firewall box itself. It works both ways: if the outside host
replies, the Linux box will silently forward the traffic to the
correct local computer. This way, the computers on your local net
are completely invisible to the outside world, even though they can
reach the outside and can receive replies. It is even possible to
run globally visible servers from within a masqueraded local network
using a mechanism called portforwarding. Masquerading is also often
called NAT (Network Address Translation).
Another use of Netfilter is in transparent proxying: if a machine on
the local network tries to connect to an outside host, your Linux
box can transparently forward the traffic to a local server,
typically a caching proxy server.
Yet another use of Netfilter is building a bridging firewall. Using
a bridge with Network packet filtering enabled makes iptables "see"
the bridged traffic. For filtering on the lower network and Ethernet
protocols over the bridge, use ebtables (under bridge netfilter
configuration).
Various modules exist for netfilter which replace the previous
masquerading (ipmasqadm), packet filtering (ipchains), transparent
proxying, and portforwarding mechanisms. Please see
<file:Documentation/Changes> under "iptables" for the location of
these packages.
Make sure to say N to "Fast switching" below if you intend to say Y
here, as Fast switching currently bypasses netfilter.
Chances are that you should say Y here if you compile a kernel which
will run as a router and N for regular hosts. If unsure, say N.
if NETFILTER
config NETFILTER_DEBUG
bool "Network packet filtering debugging"
depends on NETFILTER
help
You can say Y here if you want to get additional messages useful in
debugging the netfilter code.
config NETFILTER_ADVANCED
bool "Advanced netfilter configuration"
depends on NETFILTER
default y
help
If you say Y here you can select between all the netfilter modules.
If you say N the more ununsual ones will not be shown and the
basic ones needed by most people will default to 'M'.
If unsure, say Y.
config BRIDGE_NETFILTER
bool "Bridged IP/ARP packets filtering"
depends on BRIDGE && NETFILTER && INET
depends on NETFILTER_ADVANCED
default y
---help---
Enabling this option will let arptables resp. iptables see bridged
ARP resp. IP traffic. If you want a bridging firewall, you probably
want this option enabled.
Enabling or disabling this option doesn't enable or disable
ebtables.
If unsure, say N.
source "net/netfilter/Kconfig"
source "net/ipv4/netfilter/Kconfig"
source "net/ipv6/netfilter/Kconfig"
source "net/decnet/netfilter/Kconfig"
source "net/bridge/netfilter/Kconfig"
endif
source "net/dccp/Kconfig"
source "net/sctp/Kconfig"
source "net/tipc/Kconfig"
source "net/atm/Kconfig"
source "net/802/Kconfig"
source "net/bridge/Kconfig"
source "net/dsa/Kconfig"
source "net/8021q/Kconfig"
source "net/decnet/Kconfig"
source "net/llc/Kconfig"
source "net/ipx/Kconfig"
source "drivers/net/appletalk/Kconfig"
source "net/x25/Kconfig"
source "net/lapb/Kconfig"
source "net/econet/Kconfig"
source "net/wanrouter/Kconfig"
source "net/sched/Kconfig"
menu "Network testing"
config NET_PKTGEN
tristate "Packet Generator (USE WITH CAUTION)"
depends on PROC_FS
---help---
This module will inject preconfigured packets, at a configurable
rate, out of a given interface. It is used for network interface
stress testing and performance analysis. If you don't understand
what was just said, you don't need it: say N.
Documentation on how to use the packet generator can be found
at <file:Documentation/networking/pktgen.txt>.
To compile this code as a module, choose M here: the
module will be called pktgen.
config NET_TCPPROBE
tristate "TCP connection probing"
depends on INET && EXPERIMENTAL && PROC_FS && KPROBES
---help---
This module allows for capturing the changes to TCP connection
state in response to incoming packets. It is used for debugging
TCP congestion avoidance modules. If you don't understand
what was just said, you don't need it: say N.
Documentation on how to use TCP connection probing can be found
at http://linux-net.osdl.org/index.php/TcpProbe
To compile this code as a module, choose M here: the
module will be called tcp_probe.
endmenu
endmenu
source "net/ax25/Kconfig"
source "net/can/Kconfig"
source "net/irda/Kconfig"
source "net/bluetooth/Kconfig"
source "net/rxrpc/Kconfig"
source "net/phonet/Kconfig"
config FIB_RULES
bool
menuconfig WIRELESS
bool "Wireless"
depends on !S390
default y
if WIRELESS
source "net/wireless/Kconfig"
source "net/mac80211/Kconfig"
source "net/ieee80211/Kconfig"
endif # WIRELESS
source "net/rfkill/Kconfig"
source "net/9p/Kconfig"
endif # if NET