5bf52c4fda
This header is provided to better understand loginfo codes returned by the mpt fusion firmware. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
179 lines
13 KiB
C
179 lines
13 KiB
C
|
|
/***************************************************************************
|
|
* *
|
|
* Copyright 2003 LSI Logic Corporation. All rights reserved. *
|
|
* *
|
|
* Description *
|
|
* ------------ *
|
|
* This include file contains SAS firmware interface IOC Log Info codes *
|
|
* *
|
|
*-------------------------------------------------------------------------*
|
|
*/
|
|
|
|
#ifndef IOPI_IOCLOGINFO_H_INCLUDED
|
|
#define IOPI_IOCLOGINFO_H_INCLUDED
|
|
|
|
|
|
/****************************************************************************/
|
|
/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */
|
|
/* Format: */
|
|
/* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */
|
|
/* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */
|
|
/* Bits 23-16: LOGINFO_CODE */
|
|
/* Bits 15-0: LOGINFO_CODE Specific */
|
|
/****************************************************************************/
|
|
|
|
/****************************************************************************/
|
|
/* IOC_LOGINFO_ORIGINATOR defines */
|
|
/****************************************************************************/
|
|
#define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000)
|
|
#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000)
|
|
#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000)
|
|
|
|
#define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000)
|
|
|
|
/****************************************************************************/
|
|
/* LOGINFO_CODE defines */
|
|
/****************************************************************************/
|
|
#define IOC_LOGINFO_CODE_MASK (0x00FF0000)
|
|
#define IOC_LOGINFO_CODE_SHIFT (16)
|
|
|
|
/****************************************************************************/
|
|
/* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */
|
|
/****************************************************************************/
|
|
#define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000)
|
|
#define IOP_LOGINFO_CODE_UNUSED2 (0x00020000)
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000)
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */
|
|
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */
|
|
#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000)
|
|
|
|
#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */
|
|
#define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */
|
|
|
|
#define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001)
|
|
#define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002)
|
|
#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003)
|
|
#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004)
|
|
#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005)
|
|
|
|
/****************************************************************************/
|
|
/* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */
|
|
/****************************************************************************/
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000)
|
|
#define PL_LOG_INFO_CODE_OPEN_FAILURE_NO_DEST_TIME_OUT (0x00010001)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_BAD_DESTINATION (0x00010011)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_PROTOCOL_NOT_SUPPORTED (0x00010013)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_STP_RESOURCES_BSY (0x00010018)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_WRONG_DESTINATION (0x00010019)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_ORR_TIMEOUT (0X0001001A)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_PATHWAY_BLOCKED (0x0001001B)
|
|
#define PL_LOGINFO_CODE_OPEN_FAILURE_AWT_MAXED (0x0001001C)
|
|
#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000)
|
|
#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000)
|
|
#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000)
|
|
#define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000)
|
|
#define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000)
|
|
#define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000)
|
|
#define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000)
|
|
#define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000)
|
|
#define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000)
|
|
#define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000)
|
|
#define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000)
|
|
#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000)
|
|
#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000)
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000)
|
|
#define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */
|
|
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */
|
|
#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000)
|
|
#define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below */
|
|
#define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below */
|
|
#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000)
|
|
#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000)
|
|
#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000)
|
|
#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000)
|
|
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100)
|
|
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101)
|
|
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */
|
|
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATHWAY_BLOCKED (0x0000011B)
|
|
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */
|
|
|
|
#define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120)
|
|
#define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */
|
|
#define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */
|
|
|
|
|
|
#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200)
|
|
#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300)
|
|
#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400)
|
|
#define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500)
|
|
#define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600)
|
|
#define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700)
|
|
#define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800)
|
|
#define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900)
|
|
#define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00)
|
|
#define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00)
|
|
#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00)
|
|
#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00)
|
|
#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00)
|
|
#define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01)
|
|
#define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00)
|
|
#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000)
|
|
|
|
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occured on SMP Read */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occured on SMP Write */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */
|
|
#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */
|
|
|
|
#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */
|
|
#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */
|
|
#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */
|
|
#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */
|
|
#define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */
|
|
#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */
|
|
#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transfering data */
|
|
#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transfering sense data */
|
|
#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */
|
|
#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */
|
|
#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */
|
|
#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/
|
|
#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode */
|
|
|
|
|
|
/****************************************************************************/
|
|
/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */
|
|
/****************************************************************************/
|
|
#define IR_LOGINFO_CODE_UNUSED1 (0x00010000)
|
|
#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
|
|
|
|
/****************************************************************************/
|
|
/* Defines for convienence */
|
|
/****************************************************************************/
|
|
#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)
|
|
#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)
|
|
#define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR)
|
|
|
|
#endif /* end of file */
|
|
|