linux/drivers/net/wireless/wl12xx/wl1271_conf.h
Juuso Oikarinen 45b531a86f wl1271: Add config structure for TX path parameters
Add a configuration structure for TX path parameters, and set defalt
configuration values there.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27 16:48:08 -04:00

450 lines
10 KiB
C

/*
* This file is part of wl1271
*
* Copyright (C) 2009 Nokia Corporation
*
* Contact: Luciano Coelho <luciano.coelho@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#ifndef __WL1271_CONF_H__
#define __WL1271_CONF_H__
enum {
CONF_HW_BIT_RATE_1MBPS = BIT(0),
CONF_HW_BIT_RATE_2MBPS = BIT(1),
CONF_HW_BIT_RATE_5_5MBPS = BIT(2),
CONF_HW_BIT_RATE_6MBPS = BIT(3),
CONF_HW_BIT_RATE_9MBPS = BIT(4),
CONF_HW_BIT_RATE_11MBPS = BIT(5),
CONF_HW_BIT_RATE_12MBPS = BIT(6),
CONF_HW_BIT_RATE_18MBPS = BIT(7),
CONF_HW_BIT_RATE_22MBPS = BIT(8),
CONF_HW_BIT_RATE_24MBPS = BIT(9),
CONF_HW_BIT_RATE_36MBPS = BIT(10),
CONF_HW_BIT_RATE_48MBPS = BIT(11),
CONF_HW_BIT_RATE_54MBPS = BIT(12),
CONF_HW_BIT_RATE_MCS_0 = BIT(13),
CONF_HW_BIT_RATE_MCS_1 = BIT(14),
CONF_HW_BIT_RATE_MCS_2 = BIT(15),
CONF_HW_BIT_RATE_MCS_3 = BIT(16),
CONF_HW_BIT_RATE_MCS_4 = BIT(17),
CONF_HW_BIT_RATE_MCS_5 = BIT(18),
CONF_HW_BIT_RATE_MCS_6 = BIT(19),
CONF_HW_BIT_RATE_MCS_7 = BIT(20)
};
enum {
CONF_HW_RATE_INDEX_1MBPS = 0,
CONF_HW_RATE_INDEX_2MBPS = 1,
CONF_HW_RATE_INDEX_5_5MBPS = 2,
CONF_HW_RATE_INDEX_6MBPS = 3,
CONF_HW_RATE_INDEX_9MBPS = 4,
CONF_HW_RATE_INDEX_11MBPS = 5,
CONF_HW_RATE_INDEX_12MBPS = 6,
CONF_HW_RATE_INDEX_18MBPS = 7,
CONF_HW_RATE_INDEX_22MBPS = 8,
CONF_HW_RATE_INDEX_24MBPS = 9,
CONF_HW_RATE_INDEX_36MBPS = 10,
CONF_HW_RATE_INDEX_48MBPS = 11,
CONF_HW_RATE_INDEX_54MBPS = 12,
CONF_HW_RATE_INDEX_MAX = CONF_HW_RATE_INDEX_54MBPS,
};
struct conf_sg_settings {
/*
* Defines the PER threshold in PPM of the BT voice of which reaching
* this value will trigger raising the priority of the BT voice by
* the BT IP until next NFS sample interval time as defined in
* nfs_sample_interval.
*
* Unit: PER value in PPM (parts per million)
* #Error_packets / #Total_packets
* Range: u32
*/
u32 per_threshold;
/*
* This value is an absolute time in micro-seconds to limit the
* maximum scan duration compensation while in SG
*/
u32 max_scan_compensation_time;
/* Defines the PER threshold of the BT voice of which reaching this
* value will trigger raising the priority of the BT voice until next
* NFS sample interval time as defined in sample_interval.
*
* Unit: msec
* Range: 1-65000
*/
u16 nfs_sample_interval;
/*
* Defines the load ratio for the BT.
* The WLAN ratio is: 100 - load_ratio
*
* Unit: Percent
* Range: 0-100
*/
u8 load_ratio;
/*
* true - Co-ex is allowed to enter/exit P.S automatically and
* transparently to the host
*
* false - Co-ex is disallowed to enter/exit P.S and will trigger an
* event to the host to notify for the need to enter/exit P.S
* due to BT change state
*
*/
u8 auto_ps_mode;
/*
* This parameter defines the compensation percentage of num of probe
* requests in case scan is initiated during BT voice/BT ACL
* guaranteed link.
*
* Unit: Percent
* Range: 0-255 (0 - No compensation)
*/
u8 probe_req_compensation;
/*
* This parameter defines the compensation percentage of scan window
* size in case scan is initiated during BT voice/BT ACL Guaranteed
* link.
*
* Unit: Percent
* Range: 0-255 (0 - No compensation)
*/
u8 scan_window_compensation;
/*
* Defines the antenna configuration.
*
* Range: 0 - Single Antenna; 1 - Dual Antenna
*/
u8 antenna_config;
/*
* The percent out of the Max consecutive beacon miss roaming trigger
* which is the threshold for raising the priority of beacon
* reception.
*
* Range: 1-100
* N = MaxConsecutiveBeaconMiss
* P = coexMaxConsecutiveBeaconMissPrecent
* Threshold = MIN( N-1, round(N * P / 100))
*/
u8 beacon_miss_threshold;
/*
* The RX rate threshold below which rate adaptation is assumed to be
* occurring at the AP which will raise priority for ACTIVE_RX and RX
* SP.
*
* Range: HW_BIT_RATE_*
*/
u32 rate_adaptation_threshold;
/*
* The SNR above which the RX rate threshold indicating AP rate
* adaptation is valid
*
* Range: -128 - 127
*/
s8 rate_adaptation_snr;
};
enum conf_rx_queue_type {
CONF_RX_QUEUE_TYPE_LOW_PRIORITY, /* All except the high priority */
CONF_RX_QUEUE_TYPE_HIGH_PRIORITY, /* Management and voice packets */
};
struct conf_rx_settings {
/*
* The maximum amount of time, in TU, before the
* firmware discards the MSDU.
*
* Range: 0 - 0xFFFFFFFF
*/
u32 rx_msdu_life_time;
/*
* Packet detection threshold in the PHY.
*
* FIXME: details unknown.
*/
u32 packet_detection_threshold;
/*
* The longest time the STA will wait to receive traffic from the AP
* after a PS-poll has been transmitted.
*
* Range: 0 - 200000
*/
u16 ps_poll_timeout;
/*
* The longest time the STA will wait to receive traffic from the AP
* after a frame has been sent from an UPSD enabled queue.
*
* Range: 0 - 200000
*/
u16 upsd_timeout;
/*
* The number of octets in an MPDU, below which an RTS/CTS
* handshake is not performed.
*
* Range: 0 - 4096
*/
u16 rts_threshold;
/*
* The RX Clear Channel Assessment threshold in the PHY
* (the energy threshold).
*
* Range: ENABLE_ENERGY_D == 0x140A
* DISABLE_ENERGY_D == 0xFFEF
*/
u16 rx_cca_threshold;
/*
* Occupied Rx mem-blocks number which requires interrupting the host
* (0 = no buffering, 0xffff = disabled).
*
* Range: u16
*/
u16 irq_blk_threshold;
/*
* Rx packets number which requires interrupting the host
* (0 = no buffering).
*
* Range: u16
*/
u16 irq_pkt_threshold;
/*
* Max time in msec the FW may delay RX-Complete interrupt.
*
* Range: 1 - 100
*/
u16 irq_timeout;
/*
* The RX queue type.
*
* Range: RX_QUEUE_TYPE_RX_LOW_PRIORITY, RX_QUEUE_TYPE_RX_HIGH_PRIORITY,
*/
u8 queue_type;
};
#define CONF_TX_MAX_RATE_CLASSES 8
#define CONF_TX_RATE_MASK_UNSPECIFIED 0
#define CONF_TX_RATE_MASK_ALL 0x1eff
#define CONF_TX_RATE_RETRY_LIMIT 10
struct conf_tx_rate_class {
/*
* The rates enabled for this rate class.
*
* Range: CONF_HW_BIT_RATE_* bit mask
*/
u32 enabled_rates;
/*
* The dot11 short retry limit used for TX retries.
*
* Range: u8
*/
u8 short_retry_limit;
/*
* The dot11 long retry limit used for TX retries.
*
* Range: u8
*/
u8 long_retry_limit;
/*
* Flags controlling the attributes of TX transmission.
*
* Range: bit 0: Truncate - when set, FW attempts to send a frame stop
* when the total valid per-rate attempts have
* been exhausted; otherwise transmissions
* will continue at the lowest available rate
* until the appropriate one of the
* short_retry_limit, long_retry_limit,
* dot11_max_transmit_msdu_life_time, or
* max_tx_life_time, is exhausted.
* 1: Preamble Override - indicates if the preamble type
* should be used in TX.
* 2: Preamble Type - the type of the preamble to be used by
* the policy (0 - long preamble, 1 - short preamble.
*/
u8 aflags;
};
#define CONF_TX_MAX_AC_COUNT 4
/* Slot number setting to start transmission at PIFS interval */
#define CONF_TX_AIFS_PIFS 1
/* Slot number setting to start transmission at DIFS interval normal
* DCF access */
#define CONF_TX_AIFS_DIFS 2
enum conf_tx_ac {
CONF_TX_AC_BE = 0, /* best effort / legacy */
CONF_TX_AC_BK = 1, /* background */
CONF_TX_AC_VI = 2, /* video */
CONF_TX_AC_VO = 3, /* voice */
CONF_TX_AC_CTS2SELF = 4, /* fictious AC, follows AC_VO */
CONF_TX_AC_ANY_TID = 0x1f
};
struct conf_tx_ac_category {
/*
* The AC class identifier.
*
* Range: enum conf_tx_ac
*/
u8 ac;
/*
* The contention window minimum size (in slots) for the access
* class.
*
* Range: u8
*/
u8 cw_min;
/*
* The contention window maximum size (in slots) for the access
* class.
*
* Range: u8
*/
u16 cw_max;
/*
* The AIF value (in slots) for the access class.
*
* Range: u8
*/
u8 aifsn;
/*
* The TX Op Limit (in microseconds) for the access class.
*
* Range: u16
*/
u16 tx_op_limit;
};
#define CONF_TX_MAX_TID_COUNT 7
enum {
CONF_CHANNEL_TYPE_DCF = 0, /* DC/LEGACY*/
CONF_CHANNEL_TYPE_EDCF = 1, /* EDCA*/
CONF_CHANNEL_TYPE_HCCA = 2, /* HCCA*/
};
enum {
CONF_PS_SCHEME_LEGACY = 0,
CONF_PS_SCHEME_UPSD_TRIGGER = 1,
CONF_PS_SCHEME_LEGACY_PSPOLL = 2,
CONF_PS_SCHEME_SAPSD = 3,
};
enum {
CONF_ACK_POLICY_LEGACY = 0,
CONF_ACK_POLICY_NO_ACK = 1,
CONF_ACK_POLICY_BLOCK = 2,
};
struct conf_tx_tid {
u8 queue_id;
u8 channel_type;
u8 tsid;
u8 ps_scheme;
u8 ack_policy;
u32 apsd_conf[2];
};
struct conf_tx_settings {
/*
* The TX ED value for TELEC Enable/Disable.
*
* Range: 0, 1
*/
u8 tx_energy_detection;
/*
* Configuration for rate classes for TX (currently only one
* rate class supported.)
*/
struct conf_tx_rate_class rc_conf;
/*
* Configuration for access categories for TX rate control.
*/
u8 ac_conf_count;
struct conf_tx_ac_category ac_conf[CONF_TX_MAX_AC_COUNT];
/*
* Configuration for TID parameters.
*/
u8 tid_conf_count;
struct conf_tx_tid tid_conf[CONF_TX_MAX_TID_COUNT];
/*
* The TX fragmentation threshold.
*
* Range: u16
*/
u16 frag_threshold;
/*
* Max time in msec the FW may delay frame TX-Complete interrupt.
*
* Range: u16
*/
u16 tx_compl_timeout;
/*
* Completed TX packet count which requires to issue the TX-Complete
* interrupt.
*
* Range: u16
*/
u16 tx_compl_threshold;
};
struct conf_drv_settings {
struct conf_sg_settings sg;
struct conf_rx_settings rx;
struct conf_tx_settings tx;
};
#endif