linux/drivers/ide/tc86c001.c
Bartlomiej Zolnierkiewicz 8776168ca2 ide: change ->set_dma_mode method parameters
Change ->set_dma_mode method parameters to match ->set_dmamode method
used in struct ata_port_operations.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2010-01-19 01:45:29 -08:00

269 lines
7.6 KiB
C

/*
* Copyright (C) 2002 Toshiba Corporation
* Copyright (C) 2005-2006 MontaVista Software, Inc. <source@mvista.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/ide.h>
#define DRV_NAME "tc86c001"
static void tc86c001_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
unsigned long scr_port = hwif->config_data + (drive->dn ? 0x02 : 0x00);
u16 mode, scr = inw(scr_port);
const u8 speed = drive->dma_mode;
switch (speed) {
case XFER_UDMA_4: mode = 0x00c0; break;
case XFER_UDMA_3: mode = 0x00b0; break;
case XFER_UDMA_2: mode = 0x00a0; break;
case XFER_UDMA_1: mode = 0x0090; break;
case XFER_UDMA_0: mode = 0x0080; break;
case XFER_MW_DMA_2: mode = 0x0070; break;
case XFER_MW_DMA_1: mode = 0x0060; break;
case XFER_MW_DMA_0: mode = 0x0050; break;
case XFER_PIO_4: mode = 0x0400; break;
case XFER_PIO_3: mode = 0x0300; break;
case XFER_PIO_2: mode = 0x0200; break;
case XFER_PIO_1: mode = 0x0100; break;
case XFER_PIO_0:
default: mode = 0x0000; break;
}
scr &= (speed < XFER_MW_DMA_0) ? 0xf8ff : 0xff0f;
scr |= mode;
outw(scr, scr_port);
}
static void tc86c001_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
drive->dma_mode = drive->pio_mode;
tc86c001_set_mode(hwif, drive);
}
/*
* HACKITY HACK
*
* This is a workaround for the limitation 5 of the TC86C001 IDE controller:
* if a DMA transfer terminates prematurely, the controller leaves the device's
* interrupt request (INTRQ) pending and does not generate a PCI interrupt (or
* set the interrupt bit in the DMA status register), thus no PCI interrupt
* will occur until a DMA transfer has been successfully completed.
*
* We work around this by initiating dummy, zero-length DMA transfer on
* a DMA timeout expiration. I found no better way to do this with the current
* IDE core than to temporarily replace a higher level driver's timer expiry
* handler with our own backing up to that handler in case our recovery fails.
*/
static int tc86c001_timer_expiry(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
ide_expiry_t *expiry = ide_get_hwifdata(hwif);
u8 dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
/* Restore a higher level driver's expiry handler first. */
hwif->expiry = expiry;
if ((dma_stat & 5) == 1) { /* DMA active and no interrupt */
unsigned long sc_base = hwif->config_data;
unsigned long twcr_port = sc_base + (drive->dn ? 0x06 : 0x04);
u8 dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
printk(KERN_WARNING "%s: DMA interrupt possibly stuck, "
"attempting recovery...\n", drive->name);
/* Stop DMA */
outb(dma_cmd & ~0x01, hwif->dma_base + ATA_DMA_CMD);
/* Setup the dummy DMA transfer */
outw(0, sc_base + 0x0a); /* Sector Count */
outw(0, twcr_port); /* Transfer Word Count 1 or 2 */
/* Start the dummy DMA transfer */
/* clear R_OR_WCTR for write */
outb(0x00, hwif->dma_base + ATA_DMA_CMD);
/* set START_STOPBM */
outb(0x01, hwif->dma_base + ATA_DMA_CMD);
/*
* If an interrupt was pending, it should come thru shortly.
* If not, a higher level driver's expiry handler should
* eventually cause some kind of recovery from the DMA stall.
*/
return WAIT_MIN_SLEEP;
}
/* Chain to the restored expiry handler if DMA wasn't active. */
if (likely(expiry != NULL))
return expiry(drive);
/* If there was no handler, "emulate" that for ide_timer_expiry()... */
return -1;
}
static void tc86c001_dma_start(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long sc_base = hwif->config_data;
unsigned long twcr_port = sc_base + (drive->dn ? 0x06 : 0x04);
unsigned long nsectors = blk_rq_sectors(hwif->rq);
/*
* We have to manually load the sector count and size into
* the appropriate system control registers for DMA to work
* with LBA48 and ATAPI devices...
*/
outw(nsectors, sc_base + 0x0a); /* Sector Count */
outw(SECTOR_SIZE / 2, twcr_port); /* Transfer Word Count 1/2 */
/* Install our timeout expiry hook, saving the current handler... */
ide_set_hwifdata(hwif, hwif->expiry);
hwif->expiry = &tc86c001_timer_expiry;
ide_dma_start(drive);
}
static u8 tc86c001_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long sc_base = pci_resource_start(dev, 5);
u16 scr1 = inw(sc_base + 0x00);
/*
* System Control 1 Register bit 13 (PDIAGN):
* 0=80-pin cable, 1=40-pin cable
*/
return (scr1 & 0x2000) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long sc_base = pci_resource_start(dev, 5);
u16 scr1 = inw(sc_base + 0x00);
/* System Control 1 Register bit 15 (Soft Reset) set */
outw(scr1 | 0x8000, sc_base + 0x00);
/* System Control 1 Register bit 14 (FIFO Reset) set */
outw(scr1 | 0x4000, sc_base + 0x00);
/* System Control 1 Register: reset clear */
outw(scr1 & ~0xc000, sc_base + 0x00);
/* Store the system control register base for convenience... */
hwif->config_data = sc_base;
if (!hwif->dma_base)
return;
/*
* Sector Count Control Register bits 0 and 1 set:
* software sets Sector Count Register for master and slave device
*/
outw(0x0003, sc_base + 0x0c);
/* Sector Count Register limit */
hwif->rqsize = 0xffff;
}
static const struct ide_port_ops tc86c001_port_ops = {
.set_pio_mode = tc86c001_set_pio_mode,
.set_dma_mode = tc86c001_set_mode,
.cable_detect = tc86c001_cable_detect,
};
static const struct ide_dma_ops tc86c001_dma_ops = {
.dma_host_set = ide_dma_host_set,
.dma_setup = ide_dma_setup,
.dma_start = tc86c001_dma_start,
.dma_end = ide_dma_end,
.dma_test_irq = ide_dma_test_irq,
.dma_lost_irq = ide_dma_lost_irq,
.dma_timer_expiry = ide_dma_sff_timer_expiry,
.dma_sff_read_status = ide_dma_sff_read_status,
};
static const struct ide_port_info tc86c001_chipset __devinitdata = {
.name = DRV_NAME,
.init_hwif = init_hwif_tc86c001,
.port_ops = &tc86c001_port_ops,
.dma_ops = &tc86c001_dma_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
};
static int __devinit tc86c001_init_one(struct pci_dev *dev,
const struct pci_device_id *id)
{
int rc;
rc = pci_enable_device(dev);
if (rc)
goto out;
rc = pci_request_region(dev, 5, DRV_NAME);
if (rc) {
printk(KERN_ERR DRV_NAME ": system control regs already in use");
goto out_disable;
}
rc = ide_pci_init_one(dev, &tc86c001_chipset, NULL);
if (rc)
goto out_release;
goto out;
out_release:
pci_release_region(dev, 5);
out_disable:
pci_disable_device(dev);
out:
return rc;
}
static void __devexit tc86c001_remove(struct pci_dev *dev)
{
ide_pci_remove(dev);
pci_release_region(dev, 5);
pci_disable_device(dev);
}
static const struct pci_device_id tc86c001_pci_tbl[] = {
{ PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE), 0 },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, tc86c001_pci_tbl);
static struct pci_driver tc86c001_pci_driver = {
.name = "TC86C001",
.id_table = tc86c001_pci_tbl,
.probe = tc86c001_init_one,
.remove = __devexit_p(tc86c001_remove),
};
static int __init tc86c001_ide_init(void)
{
return ide_pci_register_driver(&tc86c001_pci_driver);
}
static void __exit tc86c001_ide_exit(void)
{
pci_unregister_driver(&tc86c001_pci_driver);
}
module_init(tc86c001_ide_init);
module_exit(tc86c001_ide_exit);
MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
MODULE_DESCRIPTION("PCI driver module for TC86C001 IDE");
MODULE_LICENSE("GPL");