linux/arch/arm/mach-ixp4xx/nas100d-setup.c

178 lines
4.1 KiB
C

/*
* arch/arm/mach-ixp4xx/nas100d-setup.c
*
* NAS 100d board-setup
*
* based ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* Author: Alessandro Zummo <a.zummo@towertech.it>
* Author: Rod Whitby <rod@whitby.id.au>
* Maintainers: http://www.nslu2-linux.org/
*
*/
#include <linux/kernel.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
static struct flash_platform_data nas100d_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource nas100d_flash_resource = {
.flags = IORESOURCE_MEM,
};
static struct platform_device nas100d_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev.platform_data = &nas100d_flash_data,
.num_resources = 1,
.resource = &nas100d_flash_resource,
};
#ifdef CONFIG_LEDS_IXP4XX
static struct resource nas100d_led_resources[] = {
{
.name = "wlan", /* green led */
.start = 0,
.end = 0,
.flags = IXP4XX_GPIO_LOW,
},
{
.name = "ready", /* blue power led (off is flashing!) */
.start = 15,
.end = 15,
.flags = IXP4XX_GPIO_LOW,
},
{
.name = "disk", /* yellow led */
.start = 3,
.end = 3,
.flags = IXP4XX_GPIO_LOW,
},
};
static struct platform_device nas100d_leds = {
.name = "IXP4XX-GPIO-LED",
.id = -1,
.num_resources = ARRAY_SIZE(nas100d_led_resources),
.resource = nas100d_led_resources,
};
#endif
static struct ixp4xx_i2c_pins nas100d_i2c_gpio_pins = {
.sda_pin = NAS100D_SDA_PIN,
.scl_pin = NAS100D_SCL_PIN,
};
static struct platform_device nas100d_i2c_controller = {
.name = "IXP4XX-I2C",
.id = 0,
.dev.platform_data = &nas100d_i2c_gpio_pins,
.num_resources = 0,
};
static struct resource nas100d_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
}
};
static struct plat_serial8250_port nas100d_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ }
};
static struct platform_device nas100d_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = nas100d_uart_data,
.num_resources = 2,
.resource = nas100d_uart_resources,
};
static struct platform_device *nas100d_devices[] __initdata = {
&nas100d_i2c_controller,
&nas100d_flash,
#ifdef CONFIG_LEDS_IXP4XX
&nas100d_leds,
#endif
};
static void nas100d_power_off(void)
{
/* This causes the box to drop the power and go dead. */
/* enable the pwr cntl gpio */
gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT);
/* do the deed */
gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
}
static void __init nas100d_init(void)
{
ixp4xx_sys_init();
/* gpio 14 and 15 are _not_ clocks */
*IXP4XX_GPIO_GPCLKR = 0;
nas100d_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
nas100d_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
pm_power_off = nas100d_power_off;
/*
* This is only useful on a modified machine, but it is valuable
* to have it first in order to see debug messages, and so that
* it does *not* get removed if platform_add_devices fails!
*/
(void)platform_device_register(&nas100d_uart);
platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
}
MACHINE_START(NAS100D, "Iomega NAS 100d")
/* Maintainer: www.nslu2-linux.org */
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
.init_machine = nas100d_init,
MACHINE_END