linux/drivers/usb/gadget/fsl_usb2_udc.h

601 lines
23 KiB
C

/*
* Freescale USB device/endpoint management registers
*/
#ifndef __FSL_USB2_UDC_H
#define __FSL_USB2_UDC_H
/* ### define USB registers here
*/
#define USB_MAX_CTRL_PAYLOAD 64
#define USB_DR_SYS_OFFSET 0x400
/* USB DR device mode registers (Little Endian) */
struct usb_dr_device {
/* Capability register */
u8 res1[256];
u16 caplength; /* Capability Register Length */
u16 hciversion; /* Host Controller Interface Version */
u32 hcsparams; /* Host Controller Structural Parameters */
u32 hccparams; /* Host Controller Capability Parameters */
u8 res2[20];
u32 dciversion; /* Device Controller Interface Version */
u32 dccparams; /* Device Controller Capability Parameters */
u8 res3[24];
/* Operation register */
u32 usbcmd; /* USB Command Register */
u32 usbsts; /* USB Status Register */
u32 usbintr; /* USB Interrupt Enable Register */
u32 frindex; /* Frame Index Register */
u8 res4[4];
u32 deviceaddr; /* Device Address */
u32 endpointlistaddr; /* Endpoint List Address Register */
u8 res5[4];
u32 burstsize; /* Master Interface Data Burst Size Register */
u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */
u8 res6[24];
u32 configflag; /* Configure Flag Register */
u32 portsc1; /* Port 1 Status and Control Register */
u8 res7[28];
u32 otgsc; /* On-The-Go Status and Control */
u32 usbmode; /* USB Mode Register */
u32 endptsetupstat; /* Endpoint Setup Status Register */
u32 endpointprime; /* Endpoint Initialization Register */
u32 endptflush; /* Endpoint Flush Register */
u32 endptstatus; /* Endpoint Status Register */
u32 endptcomplete; /* Endpoint Complete Register */
u32 endptctrl[6]; /* Endpoint Control Registers */
};
/* USB DR host mode registers (Little Endian) */
struct usb_dr_host {
/* Capability register */
u8 res1[256];
u16 caplength; /* Capability Register Length */
u16 hciversion; /* Host Controller Interface Version */
u32 hcsparams; /* Host Controller Structural Parameters */
u32 hccparams; /* Host Controller Capability Parameters */
u8 res2[20];
u32 dciversion; /* Device Controller Interface Version */
u32 dccparams; /* Device Controller Capability Parameters */
u8 res3[24];
/* Operation register */
u32 usbcmd; /* USB Command Register */
u32 usbsts; /* USB Status Register */
u32 usbintr; /* USB Interrupt Enable Register */
u32 frindex; /* Frame Index Register */
u8 res4[4];
u32 periodiclistbase; /* Periodic Frame List Base Address Register */
u32 asynclistaddr; /* Current Asynchronous List Address Register */
u8 res5[4];
u32 burstsize; /* Master Interface Data Burst Size Register */
u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */
u8 res6[24];
u32 configflag; /* Configure Flag Register */
u32 portsc1; /* Port 1 Status and Control Register */
u8 res7[28];
u32 otgsc; /* On-The-Go Status and Control */
u32 usbmode; /* USB Mode Register */
u32 endptsetupstat; /* Endpoint Setup Status Register */
u32 endpointprime; /* Endpoint Initialization Register */
u32 endptflush; /* Endpoint Flush Register */
u32 endptstatus; /* Endpoint Status Register */
u32 endptcomplete; /* Endpoint Complete Register */
u32 endptctrl[6]; /* Endpoint Control Registers */
};
/* non-EHCI USB system interface registers (Big Endian) */
struct usb_sys_interface {
u32 snoop1;
u32 snoop2;
u32 age_cnt_thresh; /* Age Count Threshold Register */
u32 pri_ctrl; /* Priority Control Register */
u32 si_ctrl; /* System Interface Control Register */
u8 res[236];
u32 control; /* General Purpose Control Register */
};
/* ep0 transfer state */
#define WAIT_FOR_SETUP 0
#define DATA_STATE_XMIT 1
#define DATA_STATE_NEED_ZLP 2
#define WAIT_FOR_OUT_STATUS 3
#define DATA_STATE_RECV 4
/* Device Controller Capability Parameter register */
#define DCCPARAMS_DC 0x00000080
#define DCCPARAMS_DEN_MASK 0x0000001f
/* Frame Index Register Bit Masks */
#define USB_FRINDEX_MASKS 0x3fff
/* USB CMD Register Bit Masks */
#define USB_CMD_RUN_STOP 0x00000001
#define USB_CMD_CTRL_RESET 0x00000002
#define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010
#define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020
#define USB_CMD_INT_AA_DOORBELL 0x00000040
#define USB_CMD_ASP 0x00000300
#define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800
#define USB_CMD_SUTW 0x00002000
#define USB_CMD_ATDTW 0x00004000
#define USB_CMD_ITC 0x00FF0000
/* bit 15,3,2 are frame list size */
#define USB_CMD_FRAME_SIZE_1024 0x00000000
#define USB_CMD_FRAME_SIZE_512 0x00000004
#define USB_CMD_FRAME_SIZE_256 0x00000008
#define USB_CMD_FRAME_SIZE_128 0x0000000C
#define USB_CMD_FRAME_SIZE_64 0x00008000
#define USB_CMD_FRAME_SIZE_32 0x00008004
#define USB_CMD_FRAME_SIZE_16 0x00008008
#define USB_CMD_FRAME_SIZE_8 0x0000800C
/* bit 9-8 are async schedule park mode count */
#define USB_CMD_ASP_00 0x00000000
#define USB_CMD_ASP_01 0x00000100
#define USB_CMD_ASP_10 0x00000200
#define USB_CMD_ASP_11 0x00000300
#define USB_CMD_ASP_BIT_POS 8
/* bit 23-16 are interrupt threshold control */
#define USB_CMD_ITC_NO_THRESHOLD 0x00000000
#define USB_CMD_ITC_1_MICRO_FRM 0x00010000
#define USB_CMD_ITC_2_MICRO_FRM 0x00020000
#define USB_CMD_ITC_4_MICRO_FRM 0x00040000
#define USB_CMD_ITC_8_MICRO_FRM 0x00080000
#define USB_CMD_ITC_16_MICRO_FRM 0x00100000
#define USB_CMD_ITC_32_MICRO_FRM 0x00200000
#define USB_CMD_ITC_64_MICRO_FRM 0x00400000
#define USB_CMD_ITC_BIT_POS 16
/* USB STS Register Bit Masks */
#define USB_STS_INT 0x00000001
#define USB_STS_ERR 0x00000002
#define USB_STS_PORT_CHANGE 0x00000004
#define USB_STS_FRM_LST_ROLL 0x00000008
#define USB_STS_SYS_ERR 0x00000010
#define USB_STS_IAA 0x00000020
#define USB_STS_RESET 0x00000040
#define USB_STS_SOF 0x00000080
#define USB_STS_SUSPEND 0x00000100
#define USB_STS_HC_HALTED 0x00001000
#define USB_STS_RCL 0x00002000
#define USB_STS_PERIODIC_SCHEDULE 0x00004000
#define USB_STS_ASYNC_SCHEDULE 0x00008000
/* USB INTR Register Bit Masks */
#define USB_INTR_INT_EN 0x00000001
#define USB_INTR_ERR_INT_EN 0x00000002
#define USB_INTR_PTC_DETECT_EN 0x00000004
#define USB_INTR_FRM_LST_ROLL_EN 0x00000008
#define USB_INTR_SYS_ERR_EN 0x00000010
#define USB_INTR_ASYN_ADV_EN 0x00000020
#define USB_INTR_RESET_EN 0x00000040
#define USB_INTR_SOF_EN 0x00000080
#define USB_INTR_DEVICE_SUSPEND 0x00000100
/* Device Address bit masks */
#define USB_DEVICE_ADDRESS_MASK 0xFE000000
#define USB_DEVICE_ADDRESS_BIT_POS 25
/* endpoint list address bit masks */
#define USB_EP_LIST_ADDRESS_MASK 0xfffff800
/* PORTSCX Register Bit Masks */
#define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001
#define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002
#define PORTSCX_PORT_ENABLE 0x00000004
#define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008
#define PORTSCX_OVER_CURRENT_ACT 0x00000010
#define PORTSCX_OVER_CURRENT_CHG 0x00000020
#define PORTSCX_PORT_FORCE_RESUME 0x00000040
#define PORTSCX_PORT_SUSPEND 0x00000080
#define PORTSCX_PORT_RESET 0x00000100
#define PORTSCX_LINE_STATUS_BITS 0x00000C00
#define PORTSCX_PORT_POWER 0x00001000
#define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000
#define PORTSCX_PORT_TEST_CTRL 0x000F0000
#define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000
#define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000
#define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000
#define PORTSCX_PHY_LOW_POWER_SPD 0x00800000
#define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000
#define PORTSCX_PORT_SPEED_MASK 0x0C000000
#define PORTSCX_PORT_WIDTH 0x10000000
#define PORTSCX_PHY_TYPE_SEL 0xC0000000
/* bit 11-10 are line status */
#define PORTSCX_LINE_STATUS_SE0 0x00000000
#define PORTSCX_LINE_STATUS_JSTATE 0x00000400
#define PORTSCX_LINE_STATUS_KSTATE 0x00000800
#define PORTSCX_LINE_STATUS_UNDEF 0x00000C00
#define PORTSCX_LINE_STATUS_BIT_POS 10
/* bit 15-14 are port indicator control */
#define PORTSCX_PIC_OFF 0x00000000
#define PORTSCX_PIC_AMBER 0x00004000
#define PORTSCX_PIC_GREEN 0x00008000
#define PORTSCX_PIC_UNDEF 0x0000C000
#define PORTSCX_PIC_BIT_POS 14
/* bit 19-16 are port test control */
#define PORTSCX_PTC_DISABLE 0x00000000
#define PORTSCX_PTC_JSTATE 0x00010000
#define PORTSCX_PTC_KSTATE 0x00020000
#define PORTSCX_PTC_SEQNAK 0x00030000
#define PORTSCX_PTC_PACKET 0x00040000
#define PORTSCX_PTC_FORCE_EN 0x00050000
#define PORTSCX_PTC_BIT_POS 16
/* bit 27-26 are port speed */
#define PORTSCX_PORT_SPEED_FULL 0x00000000
#define PORTSCX_PORT_SPEED_LOW 0x04000000
#define PORTSCX_PORT_SPEED_HIGH 0x08000000
#define PORTSCX_PORT_SPEED_UNDEF 0x0C000000
#define PORTSCX_SPEED_BIT_POS 26
/* bit 28 is parallel transceiver width for UTMI interface */
#define PORTSCX_PTW 0x10000000
#define PORTSCX_PTW_8BIT 0x00000000
#define PORTSCX_PTW_16BIT 0x10000000
/* bit 31-30 are port transceiver select */
#define PORTSCX_PTS_UTMI 0x00000000
#define PORTSCX_PTS_ULPI 0x80000000
#define PORTSCX_PTS_FSLS 0xC0000000
#define PORTSCX_PTS_BIT_POS 30
/* otgsc Register Bit Masks */
#define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001
#define OTGSC_CTRL_VUSB_CHARGE 0x00000002
#define OTGSC_CTRL_OTG_TERM 0x00000008
#define OTGSC_CTRL_DATA_PULSING 0x00000010
#define OTGSC_STS_USB_ID 0x00000100
#define OTGSC_STS_A_VBUS_VALID 0x00000200
#define OTGSC_STS_A_SESSION_VALID 0x00000400
#define OTGSC_STS_B_SESSION_VALID 0x00000800
#define OTGSC_STS_B_SESSION_END 0x00001000
#define OTGSC_STS_1MS_TOGGLE 0x00002000
#define OTGSC_STS_DATA_PULSING 0x00004000
#define OTGSC_INTSTS_USB_ID 0x00010000
#define OTGSC_INTSTS_A_VBUS_VALID 0x00020000
#define OTGSC_INTSTS_A_SESSION_VALID 0x00040000
#define OTGSC_INTSTS_B_SESSION_VALID 0x00080000
#define OTGSC_INTSTS_B_SESSION_END 0x00100000
#define OTGSC_INTSTS_1MS 0x00200000
#define OTGSC_INTSTS_DATA_PULSING 0x00400000
#define OTGSC_INTR_USB_ID 0x01000000
#define OTGSC_INTR_A_VBUS_VALID 0x02000000
#define OTGSC_INTR_A_SESSION_VALID 0x04000000
#define OTGSC_INTR_B_SESSION_VALID 0x08000000
#define OTGSC_INTR_B_SESSION_END 0x10000000
#define OTGSC_INTR_1MS_TIMER 0x20000000
#define OTGSC_INTR_DATA_PULSING 0x40000000
/* USB MODE Register Bit Masks */
#define USB_MODE_CTRL_MODE_IDLE 0x00000000
#define USB_MODE_CTRL_MODE_DEVICE 0x00000002
#define USB_MODE_CTRL_MODE_HOST 0x00000003
#define USB_MODE_CTRL_MODE_MASK 0x00000003
#define USB_MODE_CTRL_MODE_RSV 0x00000001
#define USB_MODE_ES 0x00000004 /* Endian Select */
#define USB_MODE_SETUP_LOCK_OFF 0x00000008
#define USB_MODE_STREAM_DISABLE 0x00000010
/* Endpoint Flush Register */
#define EPFLUSH_TX_OFFSET 0x00010000
#define EPFLUSH_RX_OFFSET 0x00000000
/* Endpoint Setup Status bit masks */
#define EP_SETUP_STATUS_MASK 0x0000003F
#define EP_SETUP_STATUS_EP0 0x00000001
/* ENDPOINTCTRLx Register Bit Masks */
#define EPCTRL_TX_ENABLE 0x00800000
#define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */
#define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */
#define EPCTRL_TX_TYPE 0x000C0000
#define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */
#define EPCTRL_TX_EP_STALL 0x00010000
#define EPCTRL_RX_ENABLE 0x00000080
#define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */
#define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */
#define EPCTRL_RX_TYPE 0x0000000C
#define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */
#define EPCTRL_RX_EP_STALL 0x00000001
/* bit 19-18 and 3-2 are endpoint type */
#define EPCTRL_EP_TYPE_CONTROL 0
#define EPCTRL_EP_TYPE_ISO 1
#define EPCTRL_EP_TYPE_BULK 2
#define EPCTRL_EP_TYPE_INTERRUPT 3
#define EPCTRL_TX_EP_TYPE_SHIFT 18
#define EPCTRL_RX_EP_TYPE_SHIFT 2
/* SNOOPn Register Bit Masks */
#define SNOOP_ADDRESS_MASK 0xFFFFF000
#define SNOOP_SIZE_ZERO 0x00 /* snooping disable */
#define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */
#define SNOOP_SIZE_8KB 0x0C
#define SNOOP_SIZE_16KB 0x0D
#define SNOOP_SIZE_32KB 0x0E
#define SNOOP_SIZE_64KB 0x0F
#define SNOOP_SIZE_128KB 0x10
#define SNOOP_SIZE_256KB 0x11
#define SNOOP_SIZE_512KB 0x12
#define SNOOP_SIZE_1MB 0x13
#define SNOOP_SIZE_2MB 0x14
#define SNOOP_SIZE_4MB 0x15
#define SNOOP_SIZE_8MB 0x16
#define SNOOP_SIZE_16MB 0x17
#define SNOOP_SIZE_32MB 0x18
#define SNOOP_SIZE_64MB 0x19
#define SNOOP_SIZE_128MB 0x1A
#define SNOOP_SIZE_256MB 0x1B
#define SNOOP_SIZE_512MB 0x1C
#define SNOOP_SIZE_1GB 0x1D
#define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */
/* pri_ctrl Register Bit Masks */
#define PRI_CTRL_PRI_LVL1 0x0000000C
#define PRI_CTRL_PRI_LVL0 0x00000003
/* si_ctrl Register Bit Masks */
#define SI_CTRL_ERR_DISABLE 0x00000010
#define SI_CTRL_IDRC_DISABLE 0x00000008
#define SI_CTRL_RD_SAFE_EN 0x00000004
#define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002
#define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001
/* control Register Bit Masks */
#define USB_CTRL_IOENB 0x00000004
#define USB_CTRL_ULPI_INT0EN 0x00000001
/* Endpoint Queue Head data struct
* Rem: all the variables of qh are LittleEndian Mode
* and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr
*/
struct ep_queue_head {
u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len
and IOS(15) */
u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */
u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */
u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15),
MultO(11-10), STS (7-0) */
u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */
u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */
u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */
u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */
u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */
u32 res1;
u8 setup_buffer[8]; /* Setup data 8 bytes */
u32 res2[4];
};
/* Endpoint Queue Head Bit Masks */
#define EP_QUEUE_HEAD_MULT_POS 30
#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000
#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16
#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff)
#define EP_QUEUE_HEAD_IOS 0x00008000
#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001
#define EP_QUEUE_HEAD_IOC 0x00008000
#define EP_QUEUE_HEAD_MULTO 0x00000C00
#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040
#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080
#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF
#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0
#define EP_QUEUE_FRINDEX_MASK 0x000007FF
#define EP_MAX_LENGTH_TRANSFER 0x4000
/* Endpoint Transfer Descriptor data struct */
/* Rem: all the variables of td are LittleEndian Mode */
struct ep_td_struct {
u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set
indicate invalid */
u32 size_ioc_sts; /* Total bytes (30-16), IOC (15),
MultO(11-10), STS (7-0) */
u32 buff_ptr0; /* Buffer pointer Page 0 */
u32 buff_ptr1; /* Buffer pointer Page 1 */
u32 buff_ptr2; /* Buffer pointer Page 2 */
u32 buff_ptr3; /* Buffer pointer Page 3 */
u32 buff_ptr4; /* Buffer pointer Page 4 */
u32 res;
/* 32 bytes */
dma_addr_t td_dma; /* dma address for this td */
/* virtual address of next td specified in next_td_ptr */
struct ep_td_struct *next_td_virt;
};
/* Endpoint Transfer Descriptor bit Masks */
#define DTD_NEXT_TERMINATE 0x00000001
#define DTD_IOC 0x00008000
#define DTD_STATUS_ACTIVE 0x00000080
#define DTD_STATUS_HALTED 0x00000040
#define DTD_STATUS_DATA_BUFF_ERR 0x00000020
#define DTD_STATUS_TRANSACTION_ERR 0x00000008
#define DTD_RESERVED_FIELDS 0x80007300
#define DTD_ADDR_MASK 0xFFFFFFE0
#define DTD_PACKET_SIZE 0x7FFF0000
#define DTD_LENGTH_BIT_POS 16
#define DTD_ERROR_MASK (DTD_STATUS_HALTED | \
DTD_STATUS_DATA_BUFF_ERR | \
DTD_STATUS_TRANSACTION_ERR)
/* Alignment requirements; must be a power of two */
#define DTD_ALIGNMENT 0x20
#define QH_ALIGNMENT 2048
/* Controller dma boundary */
#define UDC_DMA_BOUNDARY 0x1000
/*-------------------------------------------------------------------------*/
/* ### driver private data
*/
struct fsl_req {
struct usb_request req;
struct list_head queue;
/* ep_queue() func will add
a request->queue into a udc_ep->queue 'd tail */
struct fsl_ep *ep;
unsigned mapped:1;
struct ep_td_struct *head, *tail; /* For dTD List
cpu endian Virtual addr */
unsigned int dtd_count;
};
#define REQ_UNCOMPLETE 1
struct fsl_ep {
struct usb_ep ep;
struct list_head queue;
struct fsl_udc *udc;
struct ep_queue_head *qh;
const struct usb_endpoint_descriptor *desc;
struct usb_gadget *gadget;
char name[14];
unsigned stopped:1;
};
#define EP_DIR_IN 1
#define EP_DIR_OUT 0
struct fsl_udc {
struct usb_gadget gadget;
struct usb_gadget_driver *driver;
struct fsl_usb2_platform_data *pdata;
struct completion *done; /* to make sure release() is done */
struct fsl_ep *eps;
unsigned int max_ep;
unsigned int irq;
struct usb_ctrlrequest local_setup_buff;
spinlock_t lock;
struct usb_phy *transceiver;
unsigned softconnect:1;
unsigned vbus_active:1;
unsigned stopped:1;
unsigned remote_wakeup:1;
unsigned already_stopped:1;
unsigned big_endian_desc:1;
struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */
struct fsl_req *status_req; /* ep0 status request */
struct dma_pool *td_pool; /* dma pool for DTD */
enum fsl_usb2_phy_modes phy_mode;
size_t ep_qh_size; /* size after alignment adjustment*/
dma_addr_t ep_qh_dma; /* dma address of QH */
u32 max_pipes; /* Device max pipes */
u32 bus_reset; /* Device is bus resetting */
u32 resume_state; /* USB state to resume */
u32 usb_state; /* USB current state */
u32 ep0_state; /* Endpoint zero state */
u32 ep0_dir; /* Endpoint zero direction: can be
USB_DIR_IN or USB_DIR_OUT */
u8 device_address; /* Device USB address */
};
/*-------------------------------------------------------------------------*/
#ifdef DEBUG
#define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \
__func__, ## args)
#else
#define DBG(fmt, args...) do{}while(0)
#endif
#if 0
static void dump_msg(const char *label, const u8 * buf, unsigned int length)
{
unsigned int start, num, i;
char line[52], *p;
if (length >= 512)
return;
DBG("%s, length %u:\n", label, length);
start = 0;
while (length > 0) {
num = min(length, 16u);
p = line;
for (i = 0; i < num; ++i) {
if (i == 8)
*p++ = ' ';
sprintf(p, " %02x", buf[i]);
p += 3;
}
*p = 0;
printk(KERN_DEBUG "%6x: %s\n", start, line);
buf += num;
start += num;
length -= num;
}
}
#endif
#ifdef VERBOSE
#define VDBG DBG
#else
#define VDBG(stuff...) do{}while(0)
#endif
#define ERR(stuff...) pr_err("udc: " stuff)
#define WARNING(stuff...) pr_warning("udc: " stuff)
#define INFO(stuff...) pr_info("udc: " stuff)
/*-------------------------------------------------------------------------*/
/* ### Add board specific defines here
*/
/*
* ### pipe direction macro from device view
*/
#define USB_RECV 0 /* OUT EP */
#define USB_SEND 1 /* IN EP */
/*
* ### internal used help routines.
*/
#define ep_index(EP) ((EP)->desc->bEndpointAddress&0xF)
#define ep_maxpacket(EP) ((EP)->ep.maxpacket)
#define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
USB_DIR_IN ):((EP)->desc->bEndpointAddress \
& USB_DIR_IN)==USB_DIR_IN)
#define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \
&udc->eps[pipe])
#define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \
* 2 + ((windex & USB_DIR_IN) ? 1 : 0))
#define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP))
static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep)
{
/* we only have one ep0 structure but two queue heads */
if (ep_index(ep) != 0)
return ep->qh;
else
return &ep->udc->ep_qh[(ep->udc->ep0_dir ==
USB_DIR_IN) ? 1 : 0];
}
struct platform_device;
#ifdef CONFIG_ARCH_MXC
int fsl_udc_clk_init(struct platform_device *pdev);
void fsl_udc_clk_finalize(struct platform_device *pdev);
void fsl_udc_clk_release(void);
#else
static inline int fsl_udc_clk_init(struct platform_device *pdev)
{
return 0;
}
static inline void fsl_udc_clk_finalize(struct platform_device *pdev)
{
}
static inline void fsl_udc_clk_release(void)
{
}
#endif
#endif