/* * Digi AccelePort USB-4 and USB-2 Serial Converters * * Copyright 2000 by Digi International * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's * usb-serial driver. * * Peter Berger (pberger@brimson.com) * Al Borchers (borchers@steinerpoint.com) * * (12/03/2001) gkh * switched to using port->open_count instead of private version. * Removed port->active * * (04/08/2001) gb * Identify version on module load. * * (11/01/2000) Adam J. Richter * usb_device_id table support * * (11/01/2000) pberger and borchers * -- Turned off the USB_DISABLE_SPD flag for write bulk urbs--it caused * USB 4 ports to hang on startup. * -- Serialized access to write urbs by adding the dp_write_urb_in_use * flag; otherwise, the driver caused SMP system hangs. Watching the * urb status is not sufficient. * * (10/05/2000) gkh * -- Fixed bug with urb->dev not being set properly, now that the usb * core needs it. * * (8/8/2000) pberger and borchers * -- Fixed close so that * - it can timeout while waiting for transmit idle, if needed; * - it ignores interrupts when flushing the port, turning * of modem signalling, and so on; * - it waits for the flush to really complete before returning. * -- Read_bulk_callback and write_bulk_callback check for a closed * port before using the tty struct or writing to the port. * -- The two changes above fix the oops caused by interrupted closes. * -- Added interruptible args to write_oob_command and set_modem_signals * and added a timeout arg to transmit_idle; needed for fixes to * close. * -- Added code for rx_throttle and rx_unthrottle so that input flow * control works. * -- Added code to set overrun, parity, framing, and break errors * (untested). * -- Set USB_DISABLE_SPD flag for write bulk urbs, so no 0 length * bulk writes are done. These hung the Digi USB device. The * 0 length bulk writes were a new feature of usb-uhci added in * the 2.4.0-test6 kernels. * -- Fixed mod inc race in open; do mod inc before sleeping to wait * for a close to finish. * * (7/31/2000) pberger * -- Fixed bugs with hardware handshaking: * - Added code to set/clear tty->hw_stopped in digi_read_oob_callback() * and digi_set_termios() * -- Added code in digi_set_termios() to * - add conditional in code handling transition from B0 to only * set RTS if RTS/CTS flow control is either not in use or if * the port is not currently throttled. * - handle turning off CRTSCTS. * * (7/30/2000) borchers * -- Added support for more than one Digi USB device by moving * globals to a private structure in the pointed to from the * usb_serial structure. * -- Moved the modem change and transmit idle wait queues into * the port private structure, so each port has its own queue * rather than sharing global queues. * -- Added support for break signals. * * (7/25/2000) pberger * -- Added USB-2 support. Note: the USB-2 supports 3 devices: two * serial and a parallel port. The parallel port is implemented * as a serial-to-parallel converter. That is, the driver actually * presents all three USB-2 interfaces as serial ports, but the third * one physically connects to a parallel device. Thus, for example, * one could plug a parallel printer into the USB-2's third port, * but from the kernel's (and userland's) point of view what's * actually out there is a serial device. * * (7/15/2000) borchers * -- Fixed race in open when a close is in progress. * -- Keep count of opens and dec the module use count for each * outstanding open when shutdown is called (on disconnect). * -- Fixed sanity checks in read_bulk_callback and write_bulk_callback * so pointers are checked before use. * -- Split read bulk callback into in band and out of band * callbacks, and no longer restart read chains if there is * a status error or a sanity error. This fixed the seg * faults and other errors we used to get on disconnect. * -- Port->active is once again a flag as usb-serial intended it * to be, not a count. Since it was only a char it would * have been limited to 256 simultaneous opens. Now the open * count is kept in the port private structure in dp_open_count. * -- Added code for modularization of the digi_acceleport driver. * * (6/27/2000) pberger and borchers * -- Zeroed out sync field in the wakeup_task before first use; * otherwise the uninitialized value might prevent the task from * being scheduled. * -- Initialized ret value to 0 in write_bulk_callback, otherwise * the uninitialized value could cause a spurious debugging message. * * (6/22/2000) pberger and borchers * -- Made cond_wait_... inline--apparently on SPARC the flags arg * to spin_lock_irqsave cannot be passed to another function * to call spin_unlock_irqrestore. Thanks to Pauline Middelink. * -- In digi_set_modem_signals the inner nested spin locks use just * spin_lock() rather than spin_lock_irqsave(). The old code * mistakenly left interrupts off. Thanks to Pauline Middelink. * -- copy_from_user (which can sleep) is no longer called while a * spinlock is held. We copy to a local buffer before getting * the spinlock--don't like the extra copy but the code is simpler. * -- Printk and dbg are no longer called while a spin lock is held. * * (6/4/2000) pberger and borchers * -- Replaced separate calls to spin_unlock_irqrestore and * interruptible_sleep_on_timeout with a new function * cond_wait_interruptible_timeout_irqrestore. This eliminates * the race condition where the wake up could happen after * the unlock and before the sleep. * -- Close now waits for output to drain. * -- Open waits until any close in progress is finished. * -- All out of band responses are now processed, not just the * first in a USB packet. * -- Fixed a bug that prevented the driver from working when the * first Digi port was not the first USB serial port--the driver * was mistakenly using the external USB serial port number to * try to index into its internal ports. * -- Fixed an SMP bug -- write_bulk_callback is called directly from * an interrupt, so spin_lock_irqsave/spin_unlock_irqrestore are * needed for locks outside write_bulk_callback that are also * acquired by write_bulk_callback to prevent deadlocks. * -- Fixed support for select() by making digi_chars_in_buffer() * return 256 when -EINPROGRESS is set, as the line discipline * code in n_tty.c expects. * -- Fixed an include file ordering problem that prevented debugging * messages from working. * -- Fixed an intermittent timeout problem that caused writes to * sometimes get stuck on some machines on some kernels. It turns * out in these circumstances write_chan() (in n_tty.c) was * asleep waiting for our wakeup call. Even though we call * wake_up_interruptible() in digi_write_bulk_callback(), there is * a race condition that could cause the wakeup to fail: if our * wake_up_interruptible() call occurs between the time that our * driver write routine finishes and write_chan() sets current->state * to TASK_INTERRUPTIBLE, the effect of our wakeup setting the state * to TASK_RUNNING will be lost and write_chan's subsequent call to * schedule() will never return (unless it catches a signal). * This race condition occurs because write_bulk_callback() (and thus * the wakeup) are called asynchronously from an interrupt, rather than * from the scheduler. We can avoid the race by calling the wakeup * from the scheduler queue and that's our fix: Now, at the end of * write_bulk_callback() we queue up a wakeup call on the scheduler * task queue. We still also invoke the wakeup directly since that * squeezes a bit more performance out of the driver, and any lost * race conditions will get cleaned up at the next scheduler run. * * NOTE: The problem also goes away if you comment out * the two code lines in write_chan() where current->state * is set to TASK_RUNNING just before calling driver.write() and to * TASK_INTERRUPTIBLE immediately afterwards. This is why the * problem did not show up with the 2.2 kernels -- they do not * include that code. * * (5/16/2000) pberger and borchers * -- Added timeouts to sleeps, to defend against lost wake ups. * -- Handle transition to/from B0 baud rate in digi_set_termios. * * (5/13/2000) pberger and borchers * -- All commands now sent on out of band port, using * digi_write_oob_command. * -- Get modem control signals whenever they change, support TIOCMGET/ * SET/BIS/BIC ioctls. * -- digi_set_termios now supports parity, word size, stop bits, and * receive enable. * -- Cleaned up open and close, use digi_set_termios and * digi_write_oob_command to set port parameters. * -- Added digi_startup_device to start read chains on all ports. * -- Write buffer is only used when count==1, to be sure put_char can * write a char (unless the buffer is full). * * (5/10/2000) pberger and borchers * -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls on open/close. * -- Fixed problem where the first incoming character is lost on * port opens after the first close on that port. Now we keep * the read_urb chain open until shutdown. * -- Added more port conditioning calls in digi_open and digi_close. * -- Convert port->active to a use count so that we can deal with multiple * opens and closes properly. * -- Fixed some problems with the locking code. * * (5/3/2000) pberger and borchers * -- First alpha version of the driver--many known limitations and bugs. * * * Locking and SMP * * - Each port, including the out-of-band port, has a lock used to * serialize all access to the port's private structure. * - The port lock is also used to serialize all writes and access to * the port's URB. * - The port lock is also used for the port write_wait condition * variable. Holding the port lock will prevent a wake up on the * port's write_wait; this can be used with cond_wait_... to be sure * the wake up is not lost in a race when dropping the lock and * sleeping waiting for the wakeup. * - digi_write() does not sleep, since it is sometimes called on * interrupt time. * - digi_write_bulk_callback() and digi_read_bulk_callback() are * called directly from interrupts. Hence spin_lock_irqsave() * and spin_unlock_irqrestore() are used in the rest of the code * for any locks they acquire. * - digi_write_bulk_callback() gets the port lock before waking up * processes sleeping on the port write_wait. It also schedules * wake ups so they happen from the scheduler, because the tty * system can miss wake ups from interrupts. * - All sleeps use a timeout of DIGI_RETRY_TIMEOUT before looping to * recheck the condition they are sleeping on. This is defensive, * in case a wake up is lost. * - Following Documentation/DocBook/kernel-locking.pdf no spin locks * are held when calling copy_to/from_user or printk. * * $Id: digi_acceleport.c,v 1.80.1.2 2000/11/02 05:45:08 root Exp $ */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* Defines */ /* * Version Information */ #define DRIVER_VERSION "v1.80.1.2" #define DRIVER_AUTHOR "Peter Berger , Al Borchers " #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" /* port output buffer length -- must be <= transfer buffer length - 2 */ /* so we can be sure to send the full buffer in one urb */ #define DIGI_OUT_BUF_SIZE 8 /* port input buffer length -- must be >= transfer buffer length - 3 */ /* so we can be sure to hold at least one full buffer from one urb */ #define DIGI_IN_BUF_SIZE 64 /* retry timeout while sleeping */ #define DIGI_RETRY_TIMEOUT (HZ/10) /* timeout while waiting for tty output to drain in close */ /* this delay is used twice in close, so the total delay could */ /* be twice this value */ #define DIGI_CLOSE_TIMEOUT (5*HZ) /* AccelePort USB Defines */ /* ids */ #define DIGI_VENDOR_ID 0x05c5 #define DIGI_2_ID 0x0002 /* USB-2 */ #define DIGI_4_ID 0x0004 /* USB-4 */ /* commands * "INB": can be used on the in-band endpoint * "OOB": can be used on the out-of-band endpoint */ #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ #define DIGI_CMD_SEND_DATA 18 /* INB */ #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ /* baud rates */ #define DIGI_BAUD_50 0 #define DIGI_BAUD_75 1 #define DIGI_BAUD_110 2 #define DIGI_BAUD_150 3 #define DIGI_BAUD_200 4 #define DIGI_BAUD_300 5 #define DIGI_BAUD_600 6 #define DIGI_BAUD_1200 7 #define DIGI_BAUD_1800 8 #define DIGI_BAUD_2400 9 #define DIGI_BAUD_4800 10 #define DIGI_BAUD_7200 11 #define DIGI_BAUD_9600 12 #define DIGI_BAUD_14400 13 #define DIGI_BAUD_19200 14 #define DIGI_BAUD_28800 15 #define DIGI_BAUD_38400 16 #define DIGI_BAUD_57600 17 #define DIGI_BAUD_76800 18 #define DIGI_BAUD_115200 19 #define DIGI_BAUD_153600 20 #define DIGI_BAUD_230400 21 #define DIGI_BAUD_460800 22 /* arguments */ #define DIGI_WORD_SIZE_5 0 #define DIGI_WORD_SIZE_6 1 #define DIGI_WORD_SIZE_7 2 #define DIGI_WORD_SIZE_8 3 #define DIGI_PARITY_NONE 0 #define DIGI_PARITY_ODD 1 #define DIGI_PARITY_EVEN 2 #define DIGI_PARITY_MARK 3 #define DIGI_PARITY_SPACE 4 #define DIGI_STOP_BITS_1 0 #define DIGI_STOP_BITS_2 1 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 #define DIGI_INPUT_FLOW_CONTROL_RTS 2 #define DIGI_INPUT_FLOW_CONTROL_DTR 4 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 #define DIGI_DTR_INACTIVE 0 #define DIGI_DTR_ACTIVE 1 #define DIGI_DTR_INPUT_FLOW_CONTROL 2 #define DIGI_RTS_INACTIVE 0 #define DIGI_RTS_ACTIVE 1 #define DIGI_RTS_INPUT_FLOW_CONTROL 2 #define DIGI_RTS_TOGGLE 3 #define DIGI_FLUSH_TX 1 #define DIGI_FLUSH_RX 2 #define DIGI_RESUME_TX 4 /* clears xoff condition */ #define DIGI_TRANSMIT_NOT_IDLE 0 #define DIGI_TRANSMIT_IDLE 1 #define DIGI_DISABLE 0 #define DIGI_ENABLE 1 #define DIGI_DEASSERT 0 #define DIGI_ASSERT 1 /* in band status codes */ #define DIGI_OVERRUN_ERROR 4 #define DIGI_PARITY_ERROR 8 #define DIGI_FRAMING_ERROR 16 #define DIGI_BREAK_ERROR 32 /* out of band status */ #define DIGI_NO_ERROR 0 #define DIGI_BAD_FIRST_PARAMETER 1 #define DIGI_BAD_SECOND_PARAMETER 2 #define DIGI_INVALID_LINE 3 #define DIGI_INVALID_OPCODE 4 /* input signals */ #define DIGI_READ_INPUT_SIGNALS_SLOT 1 #define DIGI_READ_INPUT_SIGNALS_ERR 2 #define DIGI_READ_INPUT_SIGNALS_BUSY 4 #define DIGI_READ_INPUT_SIGNALS_PE 8 #define DIGI_READ_INPUT_SIGNALS_CTS 16 #define DIGI_READ_INPUT_SIGNALS_DSR 32 #define DIGI_READ_INPUT_SIGNALS_RI 64 #define DIGI_READ_INPUT_SIGNALS_DCD 128 /* Structures */ struct digi_serial { spinlock_t ds_serial_lock; struct usb_serial_port *ds_oob_port; /* out-of-band port */ int ds_oob_port_num; /* index of out-of-band port */ int ds_device_started; }; struct digi_port { spinlock_t dp_port_lock; int dp_port_num; int dp_out_buf_len; unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; int dp_write_urb_in_use; unsigned int dp_modem_signals; wait_queue_head_t dp_modem_change_wait; int dp_transmit_idle; wait_queue_head_t dp_transmit_idle_wait; int dp_throttled; int dp_throttle_restart; wait_queue_head_t dp_flush_wait; int dp_in_close; /* close in progress */ wait_queue_head_t dp_close_wait; /* wait queue for close */ struct work_struct dp_wakeup_work; struct usb_serial_port *dp_port; }; /* Local Function Declarations */ static void digi_wakeup_write(struct usb_serial_port *port); static void digi_wakeup_write_lock(struct work_struct *work); static int digi_write_oob_command(struct usb_serial_port *port, unsigned char *buf, int count, int interruptible); static int digi_write_inb_command(struct usb_serial_port *port, unsigned char *buf, int count, unsigned long timeout); static int digi_set_modem_signals(struct usb_serial_port *port, unsigned int modem_signals, int interruptible); static int digi_transmit_idle(struct usb_serial_port *port, unsigned long timeout); static void digi_rx_throttle (struct usb_serial_port *port); static void digi_rx_unthrottle (struct usb_serial_port *port); static void digi_set_termios(struct usb_serial_port *port, struct ktermios *old_termios); static void digi_break_ctl(struct usb_serial_port *port, int break_state); static int digi_ioctl(struct usb_serial_port *port, struct file *file, unsigned int cmd, unsigned long arg); static int digi_tiocmget(struct usb_serial_port *port, struct file *file); static int digi_tiocmset(struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear); static int digi_write(struct usb_serial_port *port, const unsigned char *buf, int count); static void digi_write_bulk_callback(struct urb *urb); static int digi_write_room(struct usb_serial_port *port); static int digi_chars_in_buffer(struct usb_serial_port *port); static int digi_open(struct usb_serial_port *port, struct file *filp); static void digi_close(struct usb_serial_port *port, struct file *filp); static int digi_startup_device(struct usb_serial *serial); static int digi_startup(struct usb_serial *serial); static void digi_shutdown(struct usb_serial *serial); static void digi_read_bulk_callback(struct urb *urb); static int digi_read_inb_callback(struct urb *urb); static int digi_read_oob_callback(struct urb *urb); /* Statics */ static int debug; static struct usb_device_id id_table_combined [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, { } /* Terminating entry */ }; static struct usb_device_id id_table_2 [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, { } /* Terminating entry */ }; static struct usb_device_id id_table_4 [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE (usb, id_table_combined); static struct usb_driver digi_driver = { .name = "digi_acceleport", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, .id_table = id_table_combined, .no_dynamic_id = 1, }; /* device info needed for the Digi serial converter */ static struct usb_serial_driver digi_acceleport_2_device = { .driver = { .owner = THIS_MODULE, .name = "digi_2", }, .description = "Digi 2 port USB adapter", .usb_driver = &digi_driver, .id_table = id_table_2, .num_interrupt_in = 0, .num_bulk_in = 4, .num_bulk_out = 4, .num_ports = 3, .open = digi_open, .close = digi_close, .write = digi_write, .write_room = digi_write_room, .write_bulk_callback = digi_write_bulk_callback, .read_bulk_callback = digi_read_bulk_callback, .chars_in_buffer = digi_chars_in_buffer, .throttle = digi_rx_throttle, .unthrottle = digi_rx_unthrottle, .ioctl = digi_ioctl, .set_termios = digi_set_termios, .break_ctl = digi_break_ctl, .tiocmget = digi_tiocmget, .tiocmset = digi_tiocmset, .attach = digi_startup, .shutdown = digi_shutdown, }; static struct usb_serial_driver digi_acceleport_4_device = { .driver = { .owner = THIS_MODULE, .name = "digi_4", }, .description = "Digi 4 port USB adapter", .usb_driver = &digi_driver, .id_table = id_table_4, .num_interrupt_in = 0, .num_bulk_in = 5, .num_bulk_out = 5, .num_ports = 4, .open = digi_open, .close = digi_close, .write = digi_write, .write_room = digi_write_room, .write_bulk_callback = digi_write_bulk_callback, .read_bulk_callback = digi_read_bulk_callback, .chars_in_buffer = digi_chars_in_buffer, .throttle = digi_rx_throttle, .unthrottle = digi_rx_unthrottle, .ioctl = digi_ioctl, .set_termios = digi_set_termios, .break_ctl = digi_break_ctl, .tiocmget = digi_tiocmget, .tiocmset = digi_tiocmset, .attach = digi_startup, .shutdown = digi_shutdown, }; /* Functions */ /* * Cond Wait Interruptible Timeout Irqrestore * * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout * so that wake ups are not lost if they occur between the unlock * and the sleep. In other words, spin_unlock_irqrestore and * interruptible_sleep_on_timeout are "atomic" with respect to * wake ups. This is used to implement condition variables. * * interruptible_sleep_on_timeout is deprecated and has been replaced * with the equivalent code. */ static long cond_wait_interruptible_timeout_irqrestore( wait_queue_head_t *q, long timeout, spinlock_t *lock, unsigned long flags) { DEFINE_WAIT(wait); prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); spin_unlock_irqrestore(lock, flags); timeout = schedule_timeout(timeout); finish_wait(q, &wait); return timeout; } /* * Digi Wakeup Write * * Wake up port, line discipline, and tty processes sleeping * on writes. */ static void digi_wakeup_write_lock(struct work_struct *work) { struct digi_port *priv = container_of(work, struct digi_port, dp_wakeup_work); struct usb_serial_port *port = priv->dp_port; unsigned long flags; spin_lock_irqsave(&priv->dp_port_lock, flags); digi_wakeup_write(port); spin_unlock_irqrestore(&priv->dp_port_lock, flags); } static void digi_wakeup_write(struct usb_serial_port *port) { tty_wakeup(port->tty); } /* * Digi Write OOB Command * * Write commands on the out of band port. Commands are 4 * bytes each, multiple commands can be sent at once, and * no command will be split across USB packets. Returns 0 * if successful, -EINTR if interrupted while sleeping and * the interruptible flag is true, or a negative error * returned by usb_submit_urb. */ static int digi_write_oob_command(struct usb_serial_port *port, unsigned char *buf, int count, int interruptible) { int ret = 0; int len; struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); unsigned long flags = 0; dbg("digi_write_oob_command: TOP: port=%d, count=%d", oob_priv->dp_port_num, count); spin_lock_irqsave(&oob_priv->dp_port_lock, flags); while(count > 0) { while(oob_port->write_urb->status == -EINPROGRESS || oob_priv->dp_write_urb_in_use) { cond_wait_interruptible_timeout_irqrestore( &oob_port->write_wait, DIGI_RETRY_TIMEOUT, &oob_priv->dp_port_lock, flags); if (interruptible && signal_pending(current)) return -EINTR; spin_lock_irqsave(&oob_priv->dp_port_lock, flags); } /* len must be a multiple of 4, so commands are not split */ len = min(count, oob_port->bulk_out_size); if (len > 4) len &= ~3; memcpy(oob_port->write_urb->transfer_buffer, buf, len); oob_port->write_urb->transfer_buffer_length = len; oob_port->write_urb->dev = port->serial->dev; if ((ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0) { oob_priv->dp_write_urb_in_use = 1; count -= len; buf += len; } } spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); if (ret) err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, ret); return ret; } /* * Digi Write In Band Command * * Write commands on the given port. Commands are 4 * bytes each, multiple commands can be sent at once, and * no command will be split across USB packets. If timeout * is non-zero, write in band command will return after * waiting unsuccessfully for the URB status to clear for * timeout ticks. Returns 0 if successful, or a negative * error returned by digi_write. */ static int digi_write_inb_command(struct usb_serial_port *port, unsigned char *buf, int count, unsigned long timeout) { int ret = 0; int len; struct digi_port *priv = usb_get_serial_port_data(port); unsigned char *data = port->write_urb->transfer_buffer; unsigned long flags = 0; dbg("digi_write_inb_command: TOP: port=%d, count=%d", priv->dp_port_num, count); if (timeout) timeout += jiffies; else timeout = ULONG_MAX; spin_lock_irqsave(&priv->dp_port_lock, flags); while(count > 0 && ret == 0) { while((port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use) && time_before(jiffies, timeout)) { cond_wait_interruptible_timeout_irqrestore( &port->write_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags); if (signal_pending(current)) return -EINTR; spin_lock_irqsave(&priv->dp_port_lock, flags); } /* len must be a multiple of 4 and small enough to */ /* guarantee the write will send buffered data first, */ /* so commands are in order with data and not split */ len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); if (len > 4) len &= ~3; /* write any buffered data first */ if (priv->dp_out_buf_len > 0) { data[0] = DIGI_CMD_SEND_DATA; data[1] = priv->dp_out_buf_len; memcpy(data + 2, priv->dp_out_buf, priv->dp_out_buf_len); memcpy(data + 2 + priv->dp_out_buf_len, buf, len); port->write_urb->transfer_buffer_length = priv->dp_out_buf_len + 2 + len; } else { memcpy(data, buf, len); port->write_urb->transfer_buffer_length = len; } port->write_urb->dev = port->serial->dev; if ((ret = usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0) { priv->dp_write_urb_in_use = 1; priv->dp_out_buf_len = 0; count -= len; buf += len; } } spin_unlock_irqrestore(&priv->dp_port_lock, flags); if (ret) err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num); return ret; } /* * Digi Set Modem Signals * * Sets or clears DTR and RTS on the port, according to the * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags * for the modem_signals argument. Returns 0 if successful, * -EINTR if interrupted while sleeping, or a non-zero error * returned by usb_submit_urb. */ static int digi_set_modem_signals(struct usb_serial_port *port, unsigned int modem_signals, int interruptible) { int ret; struct digi_port *port_priv = usb_get_serial_port_data(port); struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); unsigned char *data = oob_port->write_urb->transfer_buffer; unsigned long flags = 0; dbg("digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x", port_priv->dp_port_num, modem_signals); spin_lock_irqsave(&oob_priv->dp_port_lock, flags); spin_lock(&port_priv->dp_port_lock); while(oob_port->write_urb->status == -EINPROGRESS || oob_priv->dp_write_urb_in_use) { spin_unlock(&port_priv->dp_port_lock); cond_wait_interruptible_timeout_irqrestore( &oob_port->write_wait, DIGI_RETRY_TIMEOUT, &oob_priv->dp_port_lock, flags); if (interruptible && signal_pending(current)) return -EINTR; spin_lock_irqsave(&oob_priv->dp_port_lock, flags); spin_lock(&port_priv->dp_port_lock); } data[0] = DIGI_CMD_SET_DTR_SIGNAL; data[1] = port_priv->dp_port_num; data[2] = (modem_signals&TIOCM_DTR) ? DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; data[3] = 0; data[4] = DIGI_CMD_SET_RTS_SIGNAL; data[5] = port_priv->dp_port_num; data[6] = (modem_signals&TIOCM_RTS) ? DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; data[7] = 0; oob_port->write_urb->transfer_buffer_length = 8; oob_port->write_urb->dev = port->serial->dev; if ((ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0) { oob_priv->dp_write_urb_in_use = 1; port_priv->dp_modem_signals = (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS)) | (modem_signals&(TIOCM_DTR|TIOCM_RTS)); } spin_unlock(&port_priv->dp_port_lock); spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); if (ret) err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, ret); return ret; } /* * Digi Transmit Idle * * Digi transmit idle waits, up to timeout ticks, for the transmitter * to go idle. It returns 0 if successful or a negative error. * * There are race conditions here if more than one process is calling * digi_transmit_idle on the same port at the same time. However, this * is only called from close, and only one process can be in close on a * port at a time, so its ok. */ static int digi_transmit_idle(struct usb_serial_port *port, unsigned long timeout) { int ret; unsigned char buf[2]; struct digi_port *priv = usb_get_serial_port_data(port); unsigned long flags = 0; spin_lock_irqsave(&priv->dp_port_lock, flags); priv->dp_transmit_idle = 0; spin_unlock_irqrestore(&priv->dp_port_lock, flags); buf[0] = DIGI_CMD_TRANSMIT_IDLE; buf[1] = 0; timeout += jiffies; if ((ret = digi_write_inb_command(port, buf, 2, timeout - jiffies)) != 0) return ret; spin_lock_irqsave(&priv->dp_port_lock, flags); while(time_before(jiffies, timeout) && !priv->dp_transmit_idle) { cond_wait_interruptible_timeout_irqrestore( &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags); if (signal_pending(current)) return -EINTR; spin_lock_irqsave(&priv->dp_port_lock, flags); } priv->dp_transmit_idle = 0; spin_unlock_irqrestore(&priv->dp_port_lock, flags); return 0; } static void digi_rx_throttle(struct usb_serial_port *port) { unsigned long flags; struct digi_port *priv = usb_get_serial_port_data(port); dbg("digi_rx_throttle: TOP: port=%d", priv->dp_port_num); /* stop receiving characters by not resubmitting the read urb */ spin_lock_irqsave(&priv->dp_port_lock, flags); priv->dp_throttled = 1; priv->dp_throttle_restart = 0; spin_unlock_irqrestore(&priv->dp_port_lock, flags); } static void digi_rx_unthrottle(struct usb_serial_port *port) { int ret = 0; unsigned long flags; struct digi_port *priv = usb_get_serial_port_data(port); dbg("digi_rx_unthrottle: TOP: port=%d", priv->dp_port_num); spin_lock_irqsave(&priv->dp_port_lock, flags); /* turn throttle off */ priv->dp_throttled = 0; priv->dp_throttle_restart = 0; /* restart read chain */ if (priv->dp_throttle_restart) { port->read_urb->dev = port->serial->dev; ret = usb_submit_urb(port->read_urb, GFP_ATOMIC); } spin_unlock_irqrestore(&priv->dp_port_lock, flags); if (ret) err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num); } static void digi_set_termios(struct usb_serial_port *port, struct ktermios *old_termios) { struct digi_port *priv = usb_get_serial_port_data(port); struct tty_struct *tty = port->tty; unsigned int iflag = tty->termios->c_iflag; unsigned int cflag = tty->termios->c_cflag; unsigned int old_iflag = old_termios->c_iflag; unsigned int old_cflag = old_termios->c_cflag; unsigned char buf[32]; unsigned int modem_signals; int arg,ret; int i = 0; speed_t baud; dbg("digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x", priv->dp_port_num, iflag, old_iflag, cflag, old_cflag); /* set baud rate */ if ((baud = tty_get_baud_rate(tty)) != tty_termios_baud_rate(old_termios)) { arg = -1; /* reassert DTR and (maybe) RTS on transition from B0 */ if ((old_cflag&CBAUD) == B0) { /* don't set RTS if using hardware flow control */ /* and throttling input */ modem_signals = TIOCM_DTR; if (!(tty->termios->c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) modem_signals |= TIOCM_RTS; digi_set_modem_signals(port, modem_signals, 1); } switch (baud) { /* drop DTR and RTS on transition to B0 */ case 0: digi_set_modem_signals(port, 0, 1); break; case 50: arg = DIGI_BAUD_50; break; case 75: arg = DIGI_BAUD_75; break; case 110: arg = DIGI_BAUD_110; break; case 150: arg = DIGI_BAUD_150; break; case 200: arg = DIGI_BAUD_200; break; case 300: arg = DIGI_BAUD_300; break; case 600: arg = DIGI_BAUD_600; break; case 1200: arg = DIGI_BAUD_1200; break; case 1800: arg = DIGI_BAUD_1800; break; case 2400: arg = DIGI_BAUD_2400; break; case 4800: arg = DIGI_BAUD_4800; break; case 9600: arg = DIGI_BAUD_9600; break; case 19200: arg = DIGI_BAUD_19200; break; case 38400: arg = DIGI_BAUD_38400; break; case 57600: arg = DIGI_BAUD_57600; break; case 115200: arg = DIGI_BAUD_115200; break; case 230400: arg = DIGI_BAUD_230400; break; case 460800: arg = DIGI_BAUD_460800; break; default: arg = DIGI_BAUD_9600; baud = 9600; break; } if (arg != -1) { buf[i++] = DIGI_CMD_SET_BAUD_RATE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } } /* set parity */ tty->termios->c_cflag &= ~CMSPAR; if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) { if (cflag&PARENB) { if (cflag&PARODD) arg = DIGI_PARITY_ODD; else arg = DIGI_PARITY_EVEN; } else { arg = DIGI_PARITY_NONE; } buf[i++] = DIGI_CMD_SET_PARITY; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set word size */ if ((cflag&CSIZE) != (old_cflag&CSIZE)) { arg = -1; switch (cflag&CSIZE) { case CS5: arg = DIGI_WORD_SIZE_5; break; case CS6: arg = DIGI_WORD_SIZE_6; break; case CS7: arg = DIGI_WORD_SIZE_7; break; case CS8: arg = DIGI_WORD_SIZE_8; break; default: dbg("digi_set_termios: can't handle word size %d", (cflag&CSIZE)); break; } if (arg != -1) { buf[i++] = DIGI_CMD_SET_WORD_SIZE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } } /* set stop bits */ if ((cflag&CSTOPB) != (old_cflag&CSTOPB)) { if ((cflag&CSTOPB)) arg = DIGI_STOP_BITS_2; else arg = DIGI_STOP_BITS_1; buf[i++] = DIGI_CMD_SET_STOP_BITS; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set input flow control */ if ((iflag&IXOFF) != (old_iflag&IXOFF) || (cflag&CRTSCTS) != (old_cflag&CRTSCTS)) { arg = 0; if (iflag&IXOFF) arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; else arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; if (cflag&CRTSCTS) { arg |= DIGI_INPUT_FLOW_CONTROL_RTS; /* On USB-4 it is necessary to assert RTS prior */ /* to selecting RTS input flow control. */ buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; buf[i++] = priv->dp_port_num; buf[i++] = DIGI_RTS_ACTIVE; buf[i++] = 0; } else { arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; } buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set output flow control */ if ((iflag & IXON) != (old_iflag & IXON) || (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { arg = 0; if (iflag & IXON) arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; else arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; if (cflag & CRTSCTS) { arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; } else { arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; tty->hw_stopped = 0; } buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set receive enable/disable */ if ((cflag & CREAD) != (old_cflag & CREAD)) { if (cflag & CREAD) arg = DIGI_ENABLE; else arg = DIGI_DISABLE; buf[i++] = DIGI_CMD_RECEIVE_ENABLE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } if ((ret = digi_write_oob_command(port, buf, i, 1)) != 0) dbg("digi_set_termios: write oob failed, ret=%d", ret); tty_encode_baud_rate(tty, baud, baud); } static void digi_break_ctl(struct usb_serial_port *port, int break_state) { unsigned char buf[4]; buf[0] = DIGI_CMD_BREAK_CONTROL; buf[1] = 2; /* length */ buf[2] = break_state ? 1 : 0; buf[3] = 0; /* pad */ digi_write_inb_command(port, buf, 4, 0); } static int digi_tiocmget(struct usb_serial_port *port, struct file *file) { struct digi_port *priv = usb_get_serial_port_data(port); unsigned int val; unsigned long flags; dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); spin_lock_irqsave(&priv->dp_port_lock, flags); val = priv->dp_modem_signals; spin_unlock_irqrestore(&priv->dp_port_lock, flags); return val; } static int digi_tiocmset(struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear) { struct digi_port *priv = usb_get_serial_port_data(port); unsigned int val; unsigned long flags; dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); spin_lock_irqsave(&priv->dp_port_lock, flags); val = (priv->dp_modem_signals & ~clear) | set; spin_unlock_irqrestore(&priv->dp_port_lock, flags); return digi_set_modem_signals(port, val, 1); } static int digi_ioctl(struct usb_serial_port *port, struct file *file, unsigned int cmd, unsigned long arg) { struct digi_port *priv = usb_get_serial_port_data(port); dbg("digi_ioctl: TOP: port=%d, cmd=0x%x", priv->dp_port_num, cmd); switch (cmd) { case TIOCMIWAIT: /* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/ /* TODO */ return 0; case TIOCGICOUNT: /* return count of modemline transitions */ /* TODO */ return 0; } return -ENOIOCTLCMD; } static int digi_write(struct usb_serial_port *port, const unsigned char *buf, int count) { int ret,data_len,new_len; struct digi_port *priv = usb_get_serial_port_data(port); unsigned char *data = port->write_urb->transfer_buffer; unsigned long flags = 0; dbg("digi_write: TOP: port=%d, count=%d, in_interrupt=%ld", priv->dp_port_num, count, in_interrupt()); /* copy user data (which can sleep) before getting spin lock */ count = min(count, port->bulk_out_size-2); count = min(64, count); /* be sure only one write proceeds at a time */ /* there are races on the port private buffer */ /* and races to check write_urb->status */ spin_lock_irqsave(&priv->dp_port_lock, flags); /* wait for urb status clear to submit another urb */ if (port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use) { /* buffer data if count is 1 (probably put_char) if possible */ if (count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE) { priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; new_len = 1; } else { new_len = 0; } spin_unlock_irqrestore(&priv->dp_port_lock, flags); return new_len; } /* allow space for any buffered data and for new data, up to */ /* transfer buffer size - 2 (for command and length bytes) */ new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); data_len = new_len + priv->dp_out_buf_len; if (data_len == 0) { spin_unlock_irqrestore(&priv->dp_port_lock, flags); return 0; } port->write_urb->transfer_buffer_length = data_len+2; port->write_urb->dev = port->serial->dev; *data++ = DIGI_CMD_SEND_DATA; *data++ = data_len; /* copy in buffered data first */ memcpy(data, priv->dp_out_buf, priv->dp_out_buf_len); data += priv->dp_out_buf_len; /* copy in new data */ memcpy(data, buf, new_len); if ((ret = usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0) { priv->dp_write_urb_in_use = 1; ret = new_len; priv->dp_out_buf_len = 0; } /* return length of new data written, or error */ spin_unlock_irqrestore(&priv->dp_port_lock, flags); if (ret < 0) err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num); dbg("digi_write: returning %d", ret); return ret; } static void digi_write_bulk_callback(struct urb *urb) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct usb_serial *serial; struct digi_port *priv; struct digi_serial *serial_priv; int ret = 0; int status = urb->status; dbg("digi_write_bulk_callback: TOP, urb->status=%d", status); /* port and serial sanity check */ if (port == NULL || (priv=usb_get_serial_port_data(port)) == NULL) { err("%s: port or port->private is NULL, status=%d", __FUNCTION__, status); return; } serial = port->serial; if (serial == NULL || (serial_priv=usb_get_serial_data(serial)) == NULL) { err("%s: serial or serial->private is NULL, status=%d", __FUNCTION__, status); return; } /* handle oob callback */ if (priv->dp_port_num == serial_priv->ds_oob_port_num) { dbg("digi_write_bulk_callback: oob callback"); spin_lock(&priv->dp_port_lock); priv->dp_write_urb_in_use = 0; wake_up_interruptible(&port->write_wait); spin_unlock(&priv->dp_port_lock); return; } /* try to send any buffered data on this port, if it is open */ spin_lock(&priv->dp_port_lock); priv->dp_write_urb_in_use = 0; if (port->open_count && port->write_urb->status != -EINPROGRESS && priv->dp_out_buf_len > 0) { *((unsigned char *)(port->write_urb->transfer_buffer)) = (unsigned char)DIGI_CMD_SEND_DATA; *((unsigned char *)(port->write_urb->transfer_buffer)+1) = (unsigned char)priv->dp_out_buf_len; port->write_urb->transfer_buffer_length = priv->dp_out_buf_len+2; port->write_urb->dev = serial->dev; memcpy(port->write_urb->transfer_buffer+2, priv->dp_out_buf, priv->dp_out_buf_len); if ((ret = usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0) { priv->dp_write_urb_in_use = 1; priv->dp_out_buf_len = 0; } } /* wake up processes sleeping on writes immediately */ digi_wakeup_write(port); /* also queue up a wakeup at scheduler time, in case we */ /* lost the race in write_chan(). */ schedule_work(&priv->dp_wakeup_work); spin_unlock(&priv->dp_port_lock); if (ret) err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num); } static int digi_write_room(struct usb_serial_port *port) { int room; struct digi_port *priv = usb_get_serial_port_data(port); unsigned long flags = 0; spin_lock_irqsave(&priv->dp_port_lock, flags); if (port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use) room = 0; else room = port->bulk_out_size - 2 - priv->dp_out_buf_len; spin_unlock_irqrestore(&priv->dp_port_lock, flags); dbg("digi_write_room: port=%d, room=%d", priv->dp_port_num, room); return room; } static int digi_chars_in_buffer(struct usb_serial_port *port) { struct digi_port *priv = usb_get_serial_port_data(port); if (port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use) { dbg("digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, port->bulk_out_size - 2); /* return(port->bulk_out_size - 2); */ return 256; } else { dbg("digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, priv->dp_out_buf_len); return priv->dp_out_buf_len; } } static int digi_open(struct usb_serial_port *port, struct file *filp) { int ret; unsigned char buf[32]; struct digi_port *priv = usb_get_serial_port_data(port); struct ktermios not_termios; unsigned long flags = 0; dbg("digi_open: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count); /* be sure the device is started up */ if (digi_startup_device(port->serial) != 0) return -ENXIO; spin_lock_irqsave(&priv->dp_port_lock, flags); /* don't wait on a close in progress for non-blocking opens */ if (priv->dp_in_close && (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0) { spin_unlock_irqrestore(&priv->dp_port_lock, flags); return -EAGAIN; } /* wait for a close in progress to finish */ while(priv->dp_in_close) { cond_wait_interruptible_timeout_irqrestore( &priv->dp_close_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags); if (signal_pending(current)) return -EINTR; spin_lock_irqsave(&priv->dp_port_lock, flags); } spin_unlock_irqrestore(&priv->dp_port_lock, flags); /* read modem signals automatically whenever they change */ buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; buf[1] = priv->dp_port_num; buf[2] = DIGI_ENABLE; buf[3] = 0; /* flush fifos */ buf[4] = DIGI_CMD_IFLUSH_FIFO; buf[5] = priv->dp_port_num; buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; buf[7] = 0; if ((ret = digi_write_oob_command(port, buf, 8, 1)) != 0) dbg("digi_open: write oob failed, ret=%d", ret); /* set termios settings */ not_termios.c_cflag = ~port->tty->termios->c_cflag; not_termios.c_iflag = ~port->tty->termios->c_iflag; digi_set_termios(port, ¬_termios); /* set DTR and RTS */ digi_set_modem_signals(port, TIOCM_DTR|TIOCM_RTS, 1); return 0; } static void digi_close(struct usb_serial_port *port, struct file *filp) { DEFINE_WAIT(wait); int ret; unsigned char buf[32]; struct tty_struct *tty = port->tty; struct digi_port *priv = usb_get_serial_port_data(port); dbg("digi_close: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count); mutex_lock(&port->serial->disc_mutex); /* if disconnected, just clear flags */ if (port->serial->disconnected) goto exit; /* do cleanup only after final close on this port */ spin_lock_irq(&priv->dp_port_lock); priv->dp_in_close = 1; spin_unlock_irq(&priv->dp_port_lock); /* tell line discipline to process only XON/XOFF */ tty->closing = 1; /* wait for output to drain */ if ((filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0) tty_wait_until_sent(tty, DIGI_CLOSE_TIMEOUT); /* flush driver and line discipline buffers */ if (tty->driver->flush_buffer) tty->driver->flush_buffer(tty); tty_ldisc_flush(tty); if (port->serial->dev) { /* wait for transmit idle */ if ((filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0) { digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); } /* drop DTR and RTS */ digi_set_modem_signals(port, 0, 0); /* disable input flow control */ buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; buf[1] = priv->dp_port_num; buf[2] = DIGI_DISABLE; buf[3] = 0; /* disable output flow control */ buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; buf[5] = priv->dp_port_num; buf[6] = DIGI_DISABLE; buf[7] = 0; /* disable reading modem signals automatically */ buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; buf[9] = priv->dp_port_num; buf[10] = DIGI_DISABLE; buf[11] = 0; /* disable receive */ buf[12] = DIGI_CMD_RECEIVE_ENABLE; buf[13] = priv->dp_port_num; buf[14] = DIGI_DISABLE; buf[15] = 0; /* flush fifos */ buf[16] = DIGI_CMD_IFLUSH_FIFO; buf[17] = priv->dp_port_num; buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; buf[19] = 0; if ((ret = digi_write_oob_command(port, buf, 20, 0)) != 0) dbg("digi_close: write oob failed, ret=%d", ret); /* wait for final commands on oob port to complete */ prepare_to_wait(&priv->dp_flush_wait, &wait, TASK_INTERRUPTIBLE); schedule_timeout(DIGI_CLOSE_TIMEOUT); finish_wait(&priv->dp_flush_wait, &wait); /* shutdown any outstanding bulk writes */ usb_kill_urb(port->write_urb); } tty->closing = 0; exit: spin_lock_irq(&priv->dp_port_lock); priv->dp_write_urb_in_use = 0; priv->dp_in_close = 0; wake_up_interruptible(&priv->dp_close_wait); spin_unlock_irq(&priv->dp_port_lock); mutex_unlock(&port->serial->disc_mutex); dbg("digi_close: done"); } /* * Digi Startup Device * * Starts reads on all ports. Must be called AFTER startup, with * urbs initialized. Returns 0 if successful, non-zero error otherwise. */ static int digi_startup_device(struct usb_serial *serial) { int i,ret = 0; struct digi_serial *serial_priv = usb_get_serial_data(serial); struct usb_serial_port *port; /* be sure this happens exactly once */ spin_lock(&serial_priv->ds_serial_lock); if (serial_priv->ds_device_started) { spin_unlock(&serial_priv->ds_serial_lock); return 0; } serial_priv->ds_device_started = 1; spin_unlock(&serial_priv->ds_serial_lock); /* start reading from each bulk in endpoint for the device */ /* set USB_DISABLE_SPD flag for write bulk urbs */ for (i = 0; i < serial->type->num_ports + 1; i++) { port = serial->port[i]; port->write_urb->dev = port->serial->dev; if ((ret = usb_submit_urb(port->read_urb, GFP_KERNEL)) != 0) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, i); break; } } return ret; } static int digi_startup(struct usb_serial *serial) { int i; struct digi_port *priv; struct digi_serial *serial_priv; dbg("digi_startup: TOP"); /* allocate the private data structures for all ports */ /* number of regular ports + 1 for the out-of-band port */ for(i = 0; i < serial->type->num_ports + 1; i++) { /* allocate port private structure */ priv = kmalloc(sizeof(struct digi_port), GFP_KERNEL); if (priv == NULL) { while (--i >= 0) kfree(usb_get_serial_port_data(serial->port[i])); return 1; /* error */ } /* initialize port private structure */ spin_lock_init(&priv->dp_port_lock); priv->dp_port_num = i; priv->dp_out_buf_len = 0; priv->dp_write_urb_in_use = 0; priv->dp_modem_signals = 0; init_waitqueue_head(&priv->dp_modem_change_wait); priv->dp_transmit_idle = 0; init_waitqueue_head(&priv->dp_transmit_idle_wait); priv->dp_throttled = 0; priv->dp_throttle_restart = 0; init_waitqueue_head(&priv->dp_flush_wait); priv->dp_in_close = 0; init_waitqueue_head(&priv->dp_close_wait); INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock); priv->dp_port = serial->port[i]; /* initialize write wait queue for this port */ init_waitqueue_head(&serial->port[i]->write_wait); usb_set_serial_port_data(serial->port[i], priv); } /* allocate serial private structure */ serial_priv = kmalloc(sizeof(struct digi_serial), GFP_KERNEL); if (serial_priv == NULL) { for (i = 0; i < serial->type->num_ports + 1; i++) kfree(usb_get_serial_port_data(serial->port[i])); return 1; /* error */ } /* initialize serial private structure */ spin_lock_init(&serial_priv->ds_serial_lock); serial_priv->ds_oob_port_num = serial->type->num_ports; serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; serial_priv->ds_device_started = 0; usb_set_serial_data(serial, serial_priv); return 0; } static void digi_shutdown(struct usb_serial *serial) { int i; dbg("digi_shutdown: TOP, in_interrupt()=%ld", in_interrupt()); /* stop reads and writes on all ports */ for (i = 0; i < serial->type->num_ports + 1; i++) { usb_kill_urb(serial->port[i]->read_urb); usb_kill_urb(serial->port[i]->write_urb); } /* free the private data structures for all ports */ /* number of regular ports + 1 for the out-of-band port */ for(i = 0; i < serial->type->num_ports + 1; i++) kfree(usb_get_serial_port_data(serial->port[i])); kfree(usb_get_serial_data(serial)); } static void digi_read_bulk_callback(struct urb *urb) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct digi_port *priv; struct digi_serial *serial_priv; int ret; int status = urb->status; dbg("digi_read_bulk_callback: TOP"); /* port sanity check, do not resubmit if port is not valid */ if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) { err("%s: port or port->private is NULL, status=%d", __FUNCTION__, status); return; } if (port->serial == NULL || (serial_priv=usb_get_serial_data(port->serial)) == NULL) { err("%s: serial is bad or serial->private is NULL, status=%d", __FUNCTION__, status); return; } /* do not resubmit urb if it has any status error */ if (status) { err("%s: nonzero read bulk status: status=%d, port=%d", __FUNCTION__, status, priv->dp_port_num); return; } /* handle oob or inb callback, do not resubmit if error */ if (priv->dp_port_num == serial_priv->ds_oob_port_num) { if (digi_read_oob_callback(urb) != 0) return; } else { if (digi_read_inb_callback(urb) != 0) return; } /* continue read */ urb->dev = port->serial->dev; if ((ret = usb_submit_urb(urb, GFP_ATOMIC)) != 0) { err("%s: failed resubmitting urb, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num); } } /* * Digi Read INB Callback * * Digi Read INB Callback handles reads on the in band ports, sending * the data on to the tty subsystem. When called we know port and * port->private are not NULL and port->serial has been validated. * It returns 0 if successful, 1 if successful but the port is * throttled, and -1 if the sanity checks failed. */ static int digi_read_inb_callback(struct urb *urb) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct tty_struct *tty = port->tty; struct digi_port *priv = usb_get_serial_port_data(port); int opcode = ((unsigned char *)urb->transfer_buffer)[0]; int len = ((unsigned char *)urb->transfer_buffer)[1]; int port_status = ((unsigned char *)urb->transfer_buffer)[2]; unsigned char *data = ((unsigned char *)urb->transfer_buffer)+3; int flag,throttled; int i; int status = urb->status; /* do not process callbacks on closed ports */ /* but do continue the read chain */ if (port->open_count == 0) return 0; /* short/multiple packet check */ if (urb->actual_length != len + 2) { err("%s: INCOMPLETE OR MULTIPLE PACKET, urb->status=%d, " "port=%d, opcode=%d, len=%d, actual_length=%d, " "status=%d", __FUNCTION__, status, priv->dp_port_num, opcode, len, urb->actual_length, port_status); return -1; } spin_lock(&priv->dp_port_lock); /* check for throttle; if set, do not resubmit read urb */ /* indicate the read chain needs to be restarted on unthrottle */ throttled = priv->dp_throttled; if (throttled) priv->dp_throttle_restart = 1; /* receive data */ if (opcode == DIGI_CMD_RECEIVE_DATA) { /* get flag from port_status */ flag = 0; /* overrun is special, not associated with a char */ if (port_status & DIGI_OVERRUN_ERROR) tty_insert_flip_char(tty, 0, TTY_OVERRUN); /* break takes precedence over parity, */ /* which takes precedence over framing errors */ if (port_status & DIGI_BREAK_ERROR) flag = TTY_BREAK; else if (port_status & DIGI_PARITY_ERROR) flag = TTY_PARITY; else if (port_status & DIGI_FRAMING_ERROR) flag = TTY_FRAME; /* data length is len-1 (one byte of len is port_status) */ --len; len = tty_buffer_request_room(tty, len); if (len > 0) { /* Hot path */ if (flag == TTY_NORMAL) tty_insert_flip_string(tty, data, len); else { for(i = 0; i < len; i++) tty_insert_flip_char(tty, data[i], flag); } tty_flip_buffer_push(tty); } } spin_unlock(&priv->dp_port_lock); if (opcode == DIGI_CMD_RECEIVE_DISABLE) dbg("%s: got RECEIVE_DISABLE", __FUNCTION__); else if (opcode != DIGI_CMD_RECEIVE_DATA) dbg("%s: unknown opcode: %d", __FUNCTION__, opcode); return(throttled ? 1 : 0); } /* * Digi Read OOB Callback * * Digi Read OOB Callback handles reads on the out of band port. * When called we know port and port->private are not NULL and * the port->serial is valid. It returns 0 if successful, and * -1 if the sanity checks failed. */ static int digi_read_oob_callback(struct urb *urb) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct usb_serial *serial = port->serial; struct digi_port *priv = usb_get_serial_port_data(port); int opcode, line, status, val; int i; dbg("digi_read_oob_callback: port=%d, len=%d", priv->dp_port_num, urb->actual_length); /* handle each oob command */ for(i = 0; i < urb->actual_length - 3;) { opcode = ((unsigned char *)urb->transfer_buffer)[i++]; line = ((unsigned char *)urb->transfer_buffer)[i++]; status = ((unsigned char *)urb->transfer_buffer)[i++]; val = ((unsigned char *)urb->transfer_buffer)[i++]; dbg("digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d", opcode, line, status, val); if (status != 0 || line >= serial->type->num_ports) continue; port = serial->port[line]; if ((priv=usb_get_serial_port_data(port)) == NULL) return -1; if (opcode == DIGI_CMD_READ_INPUT_SIGNALS) { spin_lock(&priv->dp_port_lock); /* convert from digi flags to termiox flags */ if (val & DIGI_READ_INPUT_SIGNALS_CTS) { priv->dp_modem_signals |= TIOCM_CTS; /* port must be open to use tty struct */ if (port->open_count && port->tty->termios->c_cflag & CRTSCTS) { port->tty->hw_stopped = 0; digi_wakeup_write(port); } } else { priv->dp_modem_signals &= ~TIOCM_CTS; /* port must be open to use tty struct */ if (port->open_count && port->tty->termios->c_cflag & CRTSCTS) { port->tty->hw_stopped = 1; } } if (val & DIGI_READ_INPUT_SIGNALS_DSR) priv->dp_modem_signals |= TIOCM_DSR; else priv->dp_modem_signals &= ~TIOCM_DSR; if (val & DIGI_READ_INPUT_SIGNALS_RI) priv->dp_modem_signals |= TIOCM_RI; else priv->dp_modem_signals &= ~TIOCM_RI; if (val & DIGI_READ_INPUT_SIGNALS_DCD) priv->dp_modem_signals |= TIOCM_CD; else priv->dp_modem_signals &= ~TIOCM_CD; wake_up_interruptible(&priv->dp_modem_change_wait); spin_unlock(&priv->dp_port_lock); } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { spin_lock(&priv->dp_port_lock); priv->dp_transmit_idle = 1; wake_up_interruptible(&priv->dp_transmit_idle_wait); spin_unlock(&priv->dp_port_lock); } else if (opcode == DIGI_CMD_IFLUSH_FIFO) { wake_up_interruptible(&priv->dp_flush_wait); } } return 0; } static int __init digi_init(void) { int retval; retval = usb_serial_register(&digi_acceleport_2_device); if (retval) goto failed_acceleport_2_device; retval = usb_serial_register(&digi_acceleport_4_device); if (retval) goto failed_acceleport_4_device; retval = usb_register(&digi_driver); if (retval) goto failed_usb_register; info(DRIVER_VERSION ":" DRIVER_DESC); return 0; failed_usb_register: usb_serial_deregister(&digi_acceleport_4_device); failed_acceleport_4_device: usb_serial_deregister(&digi_acceleport_2_device); failed_acceleport_2_device: return retval; } static void __exit digi_exit (void) { usb_deregister(&digi_driver); usb_serial_deregister(&digi_acceleport_2_device); usb_serial_deregister(&digi_acceleport_4_device); } module_init(digi_init); module_exit(digi_exit); MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not");