The newer Atmel SoCs use normal 16bit 565 BGR/RGB for the palette data,
rather than the special intensity + 555 format.
Fill out palette data correctly on these devices, and at the same time
respect the RGB/BGR wiring mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
If used with negative polarity the PWM unit cannot be disabled. This would
result in a full contrast screen.
Instead let the PWM unit enabled using 0x0 as compare value which darkens
the display.
In result no power saving is possible if inverted contrast polarity
is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In the AT91SAM9263 Manual the HFP part in LCDTIM2 is described as follows:
* HFP: Horizontal Front Porch
Number of idle LCDDOTCK cycles at the end of the line.
Idle period is (HFP+2) LCDDOTCK cycles.
It is only a minor issue. I also changed all boards using atmel_lcdfb
I found to respect the new calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include module.h explicitly now.
[ with contributions from Axel Lin <axel.lin@gmail.com> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
register to inverted polarity.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
backlight_device_register has been expecting a const "ops" argument, and using
it as such, since 9905a43b2d. Let's make the
remaining backlight_ops instances const.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
at91sam9g45 non ES lots have an alternate pixel clock calculation formula.
Introduce this one with condition on the cpu_is_xxxxx() macros.
Newer 9g45 SOC will not have good pixel clock calculation without this
fix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a type mismatch when calling dev_info() in the
atmel_lcdfb.c driver.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Modify atmel LCD driver: atmel_lcdfb for at91sam9g10. This add a clock
management equivalent to at91sam9261.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove not needed locking of the fb_info->mm_lock mutex before a
frambuffer is registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059 " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.
Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used. Changing of these
fields before calling the framebuffer_register() are not mutexed.
This is 2.6.31 material. It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()). It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AFAICT the code which checks that the requested pixclock value is within
bounds is incorrect. It ensures that the lcdc core clock is at least
(bytes per pixel) times higher than the pixel clock rather than just
greater than or equal to.
There are tighter restrictions on the pixclock value as a function of bus
width for STN panels but even then it isn't a simple relationship as
currently checked for. IMO either something like the below patch should
be applied or else more detailed checking logic should be implemented
which takes in to account the panel type as well.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error test that follows the call to backlight_device_register semms
not to concern the right variable.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = backlight_device_register(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RGB555 wiring for the atmel LCD.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When suspending the system with atmel_lcdfb enabled, I sometimes see
this:
atmel_lcdfb atmel_lcdfb.0: FIFO underflow 0x10
Which can be explained by the fact that we're not stopping the LCD
controller and its DMA engine when suspending, we're just gating the
clocks to them.
There's another potential issue which may be harder to trigger but
much more nasty: If we gate the clocks at _just_ the right moment,
e.g. when the DMA engine is doing a bus transaction, we may cause the
DMA engine to violate the system bus protocol and cause a lockup.
Avoid these issues by shutting down the LCD controller before entering
suspend (and restarting it when resuming). This prevents the underrun
from happening in the first place, and prevents whatever nastiness is
happening when the bus clock stops in the middle of a DMA transfer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time. This allow to create framebuffer
device with larger virtual resolution. Combine with y-panning this can be
used to implement double buffering acceleration method.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Panning in the y-direction can be done by simply changing the DMA base
address. This code is already in place, but FBIOPAN_DISPLAY will
currently fail because ypanstep is 0.
Set ypanstep to 1 to indicate that we do support y-panning and also set
the necessary acceleration flags on AT91 (AVR32 already have them.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid division by zero in atmel_lcdfb_check_var() function.
If pixclock is not specified while passing a var structure in
the check_var() funtion, a division by zero occurs (when
translating pixclock to KHz).
This patch adds a checking of this value and try to choose a
video mode in the modelist.
The mode found in the probe function in added to the modelist.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manage atmel_lcdfb FIFO underflow
Resetting the LCD and DMA allows to fix screen shifting after a FIFO
underflow. It follows reset sequence from errata "LCD Screen Shifting
After a Reset".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix divider calculation and allow CLKVAL = 0 (divisor 2)
It was not possible to get the clock value 0 (divisor 2) because
the test "<=0" force the BYPASS bit to be activated instead.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Per Hedblom <per.hedblom@abem.se>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Jan Weber <jw022609@uni-greifswald.de>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AT91SAM9RL soc has a 2048 bytes deep FIFO, like AT91SAM9263.
[bn@niasdigital.com: fix build breakage in atmel_lcdfb]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds different wiring mode for the LCD screen.
The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead
"RGB-565". The major part of graphic stacks for embedded systems uses only
"RGB-565". It is possible to swap LCD IOs instead of doing this bit swapping
by software (See application note AT91SAM9 LCD Controller
http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf)
This wire swapping is done on the at91sam9rl-ek board (board code
using this patch will come later).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach atmel_lcdfb driver how to suspend/resume.
Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display). No point in wasting
power to generate images that can't be observed, after all...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.
Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.
This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.
Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set var->transp.offset and var->transp.length in 32bpp mode to indicate
that the 8 otherwise unused bits can be used for transparency.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes STN LCD support for the atmel_lcdfb framebuffer driver.
This patch is the result of a work from Jan Altenberg and has
been tested on a Hitachi SP06Q002 on at91sam9261ek.
It adds a Kconfig switch that enables the proper LCD in the
board configuration file (STN or TFT). The switch is used
in arch/arm/mach-at91/at91sam9261_devices.c & board-sam9261ek.c
as an example.
This patch includes the "Fix wrong line_length calculation"
little one from Jan and Haavard (submitted earlier).
AT91 platform informations are directly submitted trough
the at91 maintainer, here :
http://article.gmane.org/gmane.linux.kernel/543158
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: "Antonino A. Daplas" <adaplas@gmail.com>
Cc: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
