A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0,
atiixp_dma_check() will tune the correct PIO mode anyway
* jmicron: if DMA can't be used config_chipset_for_dma() should return 0,
micron_config_drive_for_dma() will tune the correct PIO mode anyway
config_jmicron_chipset_for_pio(drive, !speed) doesn't program
device transfer mode for speed != 0 (only wastes some CPU cycles
on ide_get_best_pio_mode() call) so remove it
* triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0,
triflex_config_drive_xfer_rate() will tune correct PIO mode anyway
Above changes also fix (theoretical) issue when ->speedproc fails to set
device transfer mode (i.e. when ide_config_drive_speed() fails to program it)
but one of DMA transfer modes is already enabled on the device by the BIOS.
In such scenario ide_dma_enable() will incorrectly return true statement
and ->ide_dma_check will try to enable DMA on the device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remember to clear reg2 bits for the current device before setting mode
* remove no longer needed hpt34x_clear_chipset()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The current driver is not setting the dev field in the private data
structure, which can lead to an OOPS if the driver tries to report an
error.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds
clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386).
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: fix printk ckeanups]
[akpm@osdl.org: hpet build fix]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SysRq-Q to print pending timers and other timer info.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clockevent drivers for i386: lapic (local) and PIT/HPET (global). Update
the timer IRQ to call into the PIT/HPET driver's event handler and the
lapic-timer IRQ to call into the lapic clockevent driver. The assignement of
timer functionality is delegated to the core framework code and replaces the
compile and runtime evalution in do_timer_interrupt_hook()
Use the clockevents broadcast support and implement the lapic_broadcast
function for ACPI.
No changes to existing functionality.
[ kdump fix from Vivek Goyal <vgoyal@in.ibm.com> ]
[ fixes based on review feedback from Arjan van de Ven <arjan@infradead.org> ]
Cleanups-from: Adrian Bunk <bunk@stusta.de>
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.
Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c
This is a preperatory patch for the rework of the local apic timer
calibration.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preperatory patch for highres/dyntick:
- replace the big #ifdef ARCH_APICTIMER_STOPS_ON_C3 hackery by functions
- remove the double switch in the power verify function (in the worst case
we switched ipi to apic and 20usec later apic to ipi)
- keep track of the the state which stops local APIC timer
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <len.brown@intel.com>
Cc: <linux-acpi@vger.kernel.org>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
apic.h does not get included on UP compiles. That way the
APICTIMER_STOPS_ON_C3 is not there and UP boxen have no support for timer
broadcasting. This was never noticed, because the lapic timer is only used
for profiling on UP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- hrtimers did not use the hrtimer_restart enum and relied on the implict
int representation. Fix the prototypes and the functions using the enums.
- Use seperate name spaces for the enumerations
- Convert hrtimer_restart macro to inline function
- Add comments
No functional changes.
[akpm@osdl.org: fix input driver]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This modifies drivers/ata/sata_vsc.c to only set the cache line size
to 0x80 if the default value is zero. Apparently zero isn't allowed
due to a bug in the chip, but I've found performance is much better
with the (non-zero) default instead of 0x80.
[note1: "default" means BIOS-programmed value, in this context -jgarzik]
[note2: superfluous braces were removed from the patch -jg]
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ADMA-capable controllers provide a bit in the status register that appears
to indicate that the controller detected an SError condition. Update sata_nv
to detect this and trigger error handling in order to handle the fault.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hald media changed polling does really confuse things.
Noone knows why the delays are needed, but they give us access to the CD.
An udelay(50) will give reliable access to the drive, but there is still
one (or more) EH reset. The drive works without EH resets with udelay(100).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some devices chock if Feature is not clear when IDENTIFY is issued.
Set ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE for IDENTIFY such that whole
TF is cleared when reading ID data.
Kudos to Art Haas for testing various futile patches over several
months and Mark Lord for pointing out the fix.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is the first preparation to doing the !IORDY cases properly. Further
diffs will then add the needed logic to do it right.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the sata_promise driver to use new-style
libata error handling for 20619 (TX4000) chips. sata_promise
already uses new EH for the other chips it supports, so the
patch is quite simple:
* remove ->phy_reset and ->eng_timeout ops from pdc_pata_ops,
and instead bind ->freeze, ->thaw, ->error_handler, and
->post_internal_cmd to existing new EH functions
* drop ATA_FLAG_SRST from board_20619's flags
* remove now unused pdc_pata_phy_reset() and pdc_eng_timeout()
Tested on a TX4000 with both modern working disks and old/quirky
disks. Also used a CD-RW drive to test reading and writing CDs.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes an oversight which caused sata_promise to
not perform cable detection on the TX2plus chips' PATA ports.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The real time clock driver was using the binary number reserved for cdroms in
the sysctl binary number interface, which is a no-no. So since the sysctl
binary interface is wrong remove it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the binary sysctl interface the hpet driver was claiming to be the cdrom
driver. This is a no-no so remove support for the binary interface.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need for open files in /proc/sys/XXX to hold a reference count on
the module that provides the file to prevent module unload races. While there
is code active in the module p->used in the sysctl_table_header is
incremented, preventing the sysctl from being unregisted. Once the sysctl is
unregistered it cannot be found. Open files are also not a problem as they
revalidate the sysctl information and bump p->used before accessing module
code.
So setting de->owner is unnecessary, makes for a bad example and gets in my
way of removing ctl_table->de.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With unique binary sysctl numbers setting insert_at_head to override other
sysctl entries is pointless.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With unique sysctl binary numbers setting insert_at_head is pointless.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Corey Minyard <minyard@acm.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctls used by the md driver are have unique binary numbers so remove the
insert_at_head flag as it serves no useful purpose.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the Atmel on-chip SPI master controller.
Tested primarily on AVR32/AT32AP7000/ATSTK1000 using mtd_dataflash and the
jffs2 filesystem. Should also work fine on various AT91 ARM-based chips
like AT91SAM926x and AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet, or its
AT91 siblings, which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since serial devices are powered down when not in use and some of those
devices cannot be accessed when powered down, we need to enable power
around calls to get_mcrtl() when dumping port state via uart_line_info().
This resolves hangs observed on some machines while reading serial device
registers when a port is powered off.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return failure immediately, so we don't have to test it twice.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below works around a minor bug found in the UART of the remote
management card used in many HP ia64 and parisc servers (aka the Diva
UARTs). The problem is that the UART does not reassert the THRE interrupt
if it has been previously cleared and the IIR THRI bit is re-enabled. This
can produce a very annoying failure mode when used as a serial console,
allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it
into working again (ie. an unattended reboot could stall).
To solve this problem, a backup timer is introduced that runs alongside the
standard interrupt driven mechanism. This timer wakes up periodically,
checks for a hang condition and gets characters moving again. This backup
mechanism is only enabled if the UART is detected as having this problem,
so systems without these UARTs will have no additional overhead.
This version of the patch incorporates previous comments from Pavel and
removes races in the bug detection code. The test is now done before the
irq linking to prevent races with interrupt handler clearing the THRE
interrupt. Short delays and syncs are also added to ensure the device is
able to update register state before the result is tested.
Aristeu says:
this was tested on the following HP machines and solved the problem:
rx2600, rx2620, rx1600 and rx1620s.
hpa says:
I have seen this same bug in soft UART IP from "a major vendor."
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Always fill MTTs from CPU
IB/mthca: Merge MR and FMR space on 64-bit systems
IB/mthca: Fix access to MTT and MPT tables on non-cache-coherent CPUs
IB/mthca: Give reserved MTTs a separate cache line
IB/mthca: Fix reserved MTTs calculation on mem-free HCAs
RDMA/cxgb3: Add driver for Chelsio T3 RNIC
IB: Remove redundant "_wq" from workqueue names
RDMA/cma: Increment port number after close to avoid re-use
IB/ehca: Fix memleak on module unloading
IB/mthca: Work around gcc bug on sparc64
IPoIB: Connected mode experimental support
IB/core: Use ARRAY_SIZE macro for mandatory_table
IB/mthca: Use correct structure size in call to memset()
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPSEC]: Fix the address family to refer encap_family
[IPSEC]: changing API of xfrm6_tunnel_register
[IPSEC]: make sit use the xfrm4_tunnel_register
[IPSEC]: Changing API of xfrm4_tunnel_register.
[TCP]: Prevent pseudo garbage in SYN's advertized window
[NET_SCHED]: sch_hfsc: replace ASSERT macro by WARN_ON
[BRIDGE] br_if: Fix oops in port_carrier_check
[NETFILTER]: Clear GSO bits for TCP reset packet
[TG3]: Update copyright, version, and reldate.
[TG3]: Add some tx timeout debug messages.
[TG3]: Use constant for PHY register 0x1e.
[TG3]: Power down 5704 serdes transceiver when shutting down.
[TG3]: 5906 doesn't need to switch to slower clock.
[TG3]: 5722/5756 don't need PHY jitter workaround.
[TG3]: Use lower DMA watermark for 5703.
[TG3]: Save MSI state before suspend.
[XFRM]: Fix IPv4 tunnel mode decapsulation with IPV6=n
[IPV6] HASHTABLES: Use appropriate seed for caluculating ehash index.
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Stop using i2c_adapter.class_dev
i2c: Remove the warning on missing adapter device
i2c: Declare more i2c_adapter parent devices
i2c: PA Semi SMBus driver
i2c-amd8111: Proposed cleanups
i2c-parport: Add support for One For All remote JP1 interface
i2c-viapro: Add support for the VIA CX700 south bridge
i2c: Add IDs to adapters
i2c: Update the list of bus IDs
i2c: Add driver suspend/resume/shutdown support
i2c: completion header cleanups
i2c-i801: Document the SMBus unhiding quirk
i2c-i801: Spelling fix
i2c: Fix typo in SMBus Write Word Data description
i2c-piix4: Add support for the ATI SB600
i2c-nforce2: Drop unused reference to pci_dev
i2c/vt8231: Remove superfluous initialization
i2c-ali1563: Fix device initialization
i2c-ali1563: Improve the status messages