Hipersocket connections can encounter temporary busy conditions.
In case of the busy bit set we retry the SIGA operation immediatelly.
If the busy condition still persists after 100 ms we fail and report
the error to the upper layer. The second stage retry logic is removed.
In case of ongoing busy conditions the upper layer needs to reset the
connection.
The reporting of a SIGA error is now done synchronously to allow the
network driver to requeue the buffers. Also no error trace is created
for the temporary SIGA errors so the error message view is not flooded.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- Use automatic acknowledgement of incoming buffers in QEBSM mode
- Move ACK for non-QEBSM mode always to the newest buffer to prevent
a race with qdio_stop_polling
- Remove the polling spinlock, the upper layer drivers return new buffers
in the same code path and could not run in parallel
- Don't flood the error log in case of no-target-buffer-empty
- In handle_inbound we check if we would overwrite an ACK'ed buffer, if so
advance the pointer to the oldest ACK'ed buffer so we don't overwrite an
empty buffer in qdio_stop_polling
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- make qdio_trace a per device view
- remove s390dbf exceptions
- remove CONFIG_QDIO_DEBUG, not needed anymore if we check for the level
before calling sprintf
- use snprintf for dbf entries
- add start markers to see if the dbf view wrapped
- add a global error view for all queues
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QEBSM instructions are only available for CONFIG_64BIT, they are not
used under 31 bit. Make compiler happy about the false positive:
drivers/s390/cio/qdio_main.c: In function ?qdio_inbound_q_done?:
drivers/s390/cio/qdio_main.c:532: warning: ?state? may be used uninitialized in this function
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add counters for the eqbs and sqbs instructions that indicate how often
we issued the instructions and how often the instructions returned with
less buffers than specified.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qeth needs to get the port count information before
qdio has allocated a page for the chsc operation.
Extend qdio_get_ssqd_desc() to store the data in the
specified structure.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of I/O errors on a qdio subchannel qdio_shutdown may be
called twice by the qdio driver and by zfcp. Remove the
superfluous shutdown from qdio and let the upper layer driver
handle the error condition.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for z10 HiperSockets multiwrite SBALs on output
queues. This is used on LPAR with EDDP enabled devices.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use dev_name() in the new qdio driver.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If an asynchronous HiperSockets queue runs full, no further packet
can be sent. In this case the next initiative to give transmitted
skbs back to the stack is triggered only by a 10-seconds qdio timer.
This timer has been introduced for low multicast traffic scenarios
to guarantee freeing of skbs in a limited amount of time. For high
HiperSocket multicast traffic scenarios progress checking on the
outbound queue should be enforced by tasklet rescheduling.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increasing the qdio reference count for every used subchannel
is unnecessary since unloading qdio (if build as a module) is
only possible if other modules that use qdio are unloaded.
Unloading modules that use qdio in turn requires that these
modules shut down all qdio subchannels. Therefore the additional
module_get reference is not needed.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve s390 debug feature usage:
- log busy bit in dbf
- increase size of dbf views
- consistent logging of qdio api calls to setup view
- print subchannel number so one can associate the interface
with the dbf data
- only log events to one view
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
kzalloc does not guarantee the required alignment of qdr to page size,
use get_zeroed_page instead.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Jan Glauber