Add stub runtime_pm calls which go through the flow of enabling and
disabling but don't actually do anything with the device itself as
there's nothing useful we can do. This provides the core PM framework
with information about when the device is idle, enabling chip wide
power savings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Saves remembering to call kfree(). There's some kfree()s used by the
resource still, these will be removed in 3.3 using the newly added
devm_request_and_ioremap().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
s3c24xx_i2c_parse_dt_gpio is called when cfg_gpio is not defined
in the platform data of the i2c device. When DT is not enabled,
the above function always returns -EINVAL. Since there can be
some i2c devices which don't need to configure any gpio lines,
the probe of such devices would fail here. Changing the default
return value to success would fix this issue.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add device tree probe support for Samsung's s3c2410 i2c driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the i2c-s3c2410 driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
This patch modify the s3c2410 i2c driver behaviour to enable the
i2c clock only when needed. I'm not sure if this has a big impact
on power usage but at least it's fixing a bug with the uda1380
codec which needs to be hard reset'ed if the i2c clock is enabled
before it's powered on (at least on h1940).
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S3C2440 style I2C controller uses PCLK to calculate the SDA line delay.
The driver wrongly assumed that this delay is calculated from the
frequency that the controller is operating on. This patch fixes this
issue.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The S3C I2C controller indicates completion of I2C transfers before
the bus has a stop condition on it. In order to ensure that we do not
attempt to start a new transfer before the bus is idle the driver
currently inserts a 1ms delay. This is vastly larger than is generally
required and has a visible effect on performance under load, such as
when bringing up audio CODECs or reading back status information with
non-bulk I2C reads.
Replace the sleep with a spin on the IIC status register for up to 1ms.
This will busy wait but testing on my SMDK6410 system indicates that
the overwhelming majority of transactions complete on the first spin,
with maximum latencies of less than 10 spins so the absolute overhead
of busy waiting should be at worst comprable to msleep(), and the
overall system performance is dramatically improved.
The main risk is poor interaction with multimaster systems where
we may miss the bus going idle before the next transaction. Defend
against this by falling back to the original 1ms delay after 20 spins.
The overall effect in my testing is an approximately 20% improvement
in kernel startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is V2 of the i2c-s3c2410 dev_pm_ops patch.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume() -> resume()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is required in order to ensure that core system devices such as
voltage regulators attached via I2C are avaiable early in boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Use dev_name(dev) instead of accessing dev.bus_id directly, as the
latter is going away soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
* 'i2c-next' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: fix type of irq handler function
i2c-s3c2410: Change IRQ to be plain integer.
i2c-s3c2410: Allow more than one i2c-s3c2410 adapter
i2c-s3c2410: Remove default platform data.
i2c-s3c2410: Use platform data for gpio configuration
i2c-s3c2410: Fixup style problems from checkpatch.pl
i2c-omap: Enable I2C wakeups for 34xx
i2c-omap: reprogram OCP_SYSCONFIG register after reset
i2c-omap: convert 'rev1' flag to generic 'rev' u8
i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un,}idle()
i2c-omap: Clean-up i2c-omap
i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds
i2c-omap: Mark init-only functions as __init
i2c-omap: Add support for omap34xx
i2c-omap: FIFO handling support and broken hw workaround for i2c-omap
i2c-omap: Add high-speed support to omap-i2c
i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr()
i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg
Fix up apparently-trivial conflict in drivers/i2c/busses/i2c-s3c2410.c
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
Change the code to use a plain integer as the holder
for the IRQ for the device and use platform_get_irq()
to find it.
This makes the code slightly neater, and easier to get
the IRQ number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Newer SoCs such as the S3C6410 have 2 instances of this i2c
controller block in and thus require the ability to create
two seperate busses from this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data should now always be present when the device
is initialised, so we can remove the default platform data in
the driver.
All the device initialisation points in the board specific code
should already have been changed to initialise this as necessary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a callback to set the gpio configuration for the
i2c device instead of a set include. This also allows
the remvoal of the machine gpio and hardware files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixup the 36 warnings and errors generated from running
checkpatch.pl on the driver. The warnings are too numerous
to be listed here.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As noted by Julia Lawall <julia@diku.dk>, we can never
trigger the check for being in suspend due to the result
of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN
always being 0.
Add suspend/resume hooks to stop i2c transactions happening
until the driver has been resumed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way. In particular,
the result of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN is
always 0.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
(
!E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.
Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.
Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.
So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a MODULE_ALIAS() statement for the i2c-s3c2410 controller
to ensure that it can be autoloaded on the S3C2440 systems that
we support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver should be returning -ENXIO for transfers that do not
pass the initial address byte stage.
Note, also small tidyups to the driver comments in the area.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__FUNCTION__ is gcc-specific, use __func__.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixup the include files after the arch moves that
where included in 2.6.23.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Mark Brown