bcma now provide this data and brcmsmac should get it from there and
not parse it by its self.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac now takes the sprom from bcma and do not uses its own sprom
parsing any more. Remove this code as it is not used any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma now provides all sprom attributes needed by brcmsmac and also
parses them from the pci sprom ant otp.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
John Linville says:
Here are three more fixes that some of my developers are desperate to
see included in 3.4...
Johan Hedberg went to some length justifyng the inclusion of these two
Bluetooth fixes:
"The device_connected fix should be quite self-explanatory, but it's
actually a wider issue than just for keyboards. All profiles that do
incoming connection authorization (e.g. headsets) will break without it
with specific hardware. The reason it wasn't caught earlier is that it
only occurs with specific Bluetooth adapters.
As for the security level patch, this fixes L2CAP socket based security
level elevation during a connection. The HID profile needs this (for
keyboards) and it is the only way to achieve the security level
elevation when using the management interface to talk to the kernel
(hence the management enabling patch being the one that exposes this"
The rtlwifi fix addresses a regression related to firmware loading,
as described in kernel.org bug 43187. It basically just moves a hunk
of code to a more appropriate place.
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing resource tracking for XRC domains and complete the tracking for HCA
network flow counters.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the slave and master resources are deleted after master freed
all bitmaps. If any resources were not properly cleaned up during the
shutdown process, an Oops would result.
Fix so that delete slave (only) resources during cleanup. Master resources
are cleaned up during unload process, and need not separately be cleaned.
Note that during cleanup, we need to split the resource-tracker freeing
functionality.
Before removing all the bitmaps, we free any leftover slave resources.
However, we can only remove the resource tracker linked list after
all bitmap frees, since some of the freeing functions (e.g.,
mlx4_cleanup_eq_table) use paravirtualized FW commands which expect
the resource tracker linked list to be present.
Found-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following scenario: 2 HCAs, where only one of which can run SRIOV.
If we reset the module parameter, all the VFs of the SRIOV HCA will be
claimed by the PPF host (-- the code relies on num_vfs being non-zero
to avoid this claiming, and num_vfs was reset when pci_enable_sriov failed
for the non-SRIOV HCA).
The solution is not to touch the num_vfs parameter.
Also, eliminate the unneeded check of num_vfs when disabling sriov
(the dev flag bit is sufficient).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unsued *_str helper functions from resource_tracker.c
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "wrapped" was incorrect, since no wrapper function was defined.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_INIT_PORT_wrapper, the port state mask for the
slave is only set if we are invoking the INIT_PORT fw command.
However, the reference count for the (initialized) port is
incremented anyway.
This creates a problem in that when we have multiple slaves,
then the CLOSE_PORT command will never be invoked. The
reason is that in the CLOSE_PORT wrapper, if the port-state
mask is zero for the slave (which it is), the wrapper returns
without doing anything. The only slave which will not return
immediately in the CLOSE_PORT wrapper is that slave for which
INIT_PORT was invoked.
The fix is to not have the port-state mask setting depend
on the logic for calling the INIT_PORT fw command.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the compiler warnings on variables which are set but not used
by removing the relevant variable or casting a return value which is
ignored on purpose to void.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This represents the mass deletion of the of the tokenring support.
It gets rid of:
- the net/tr.c which the drivers depended on
- the drivers/net component
- the Kbuild infrastructure around it
- any tokenring related CONFIG_ settings in any defconfigs
- the tokenring headers in the include/linux dir
- the firmware associated with the tokenring drivers.
- any associated token ring documentation.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make use of REGAINED_BSS_EVENT and instead of reporting connection
loss immediately on each BEACON_LOSE event, try if not regained
in reasonable period of time.
Signed-off-by: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We currently do this:
int wl1271_cmd_build_arp_rsp(struct wl1271 *wl, struct wl12xx_vif *wlvif)
...
struct wl12xx_arp_rsp_template *tmpl;
struct ieee80211_hdr_3addr *hdr;
...
tmpl = (struct wl12xx_arp_rsp_template *)skb_put(skb, sizeof(*tmpl));
memset(tmpl, 0, sizeof(tmpl));
...
hdr = (struct ieee80211_hdr_3addr *)skb_push(skb, sizeof(*hdr));
memset(hdr, 0, sizeof(hdr));
...
I believe we want to set the entire structures to 0 with those
memset() calls, not just zero the initial part of them (size of the
pointer bytes).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx build fails with many undefined symbol errors when MAC80211
and CFG80211 are not enabled, so make WLCORE and WL12XX depend
on MAC80211 (which already depends on CFG80211).
Here are a few of the many build errors:
drivers/built-in.o: In function `wl1271_register_hw':
main.c:(.text+0x4197cd): undefined reference to `ieee80211_register_hw'
drivers/built-in.o: In function `wl1271_rx_streaming_timer':
main.c:(.text+0x419818): undefined reference to `ieee80211_queue_work'
drivers/built-in.o: In function `wl1271_flush_deferred_work':
main.c:(.text+0x419910): undefined reference to `ieee80211_rx'
main.c:(.text+0x419938): undefined reference to `ieee80211_tx_status'
drivers/built-in.o: In function `wl12xx_op_channel_switch':
main.c:(.text+0x419afc): undefined reference to `ieee80211_chswitch_done'
drivers/built-in.o: In function `wl1271_ssid_set':
drivers/built-in.o: In function `wl1271_event_process':
event.c:(.text+0x41fec4): undefined reference to `ieee80211_sched_scan_stopped'
event.c:(.text+0x41ff88): undefined reference to `ieee80211_cqm_rssi_notify'
event.c:(.text+0x42000d): undefined reference to `ieee80211_stop_rx_ba_session'
event.c:(.text+0x420048): undefined reference to `ieee80211_stop_rx_ba_session'
event.c:(.text+0x4200b8): undefined reference to `ieee80211_chswitch_done'
event.c:(.text+0x4201ae): undefined reference to `ieee80211_find_sta'
event.c:(.text+0x4201ba): undefined reference to `ieee80211_report_low_ack'
event.c:(.text+0x42021b): undefined reference to `ieee80211_connection_loss'
drivers/built-in.o: In function `wl1271_tx_complete_packet':
tx.c:(.text+0x4206a6): undefined reference to `ieee80211_get_hdrlen_from_skb'
drivers/built-in.o: In function `wl1271_tx_fill_hdr':
tx.c:(.text+0x4208ca): undefined reference to `ieee80211_hdrlen'
drivers/built-in.o: In function `wl1271_handle_tx_low_watermark':
(.text+0x420e25): undefined reference to `ieee80211_wake_queue'
drivers/built-in.o: In function `wl12xx_rearm_rx_streaming':
(.text+0x420ed9): undefined reference to `ieee80211_queue_work'
drivers/built-in.o: In function `wl1271_tx_work_locked':
(.text+0x421008): undefined reference to `ieee80211_free_txskb'
drivers/built-in.o: In function `wl1271_rx_status.clone.2':
rx.c:(.text+0x421593): undefined reference to `ieee80211_channel_to_frequency'
drivers/built-in.o: In function `wl1271_ps_filter_frames':
ps.c:(.text+0x421a41): undefined reference to `ieee80211_tx_status'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
GFP_DMA isn't supposed to be used by itself. This allocation is allowed
to sleep so it should be ORing it with GFP_KERNEL.
Also we should check for allocations errors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use FW RX data filters to support cfg80211 wowlan wakeup patterns.
This enables to wake up the host from suspend following detection
of certain configurable patterns within an incoming packet.
Up to 5 patterns are supported. Once the host is resumed
any configured RX data filter is cleared.
A single pattern can match several bytes sequences with different
offsets within a packet.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
More prep work to support wowlan wakeup patterns.
Added some wrappers that also keep the current filters state
updated in the driver.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
More prep work for wowlan patterns.
Added ACXs to set global RX filter behavior and
enable or disable a specific filter.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This is prep work for the support of wowlan patterns
using the FW data rx filters mechanism.
Added an rx filter struct and some util functions
required to manipulate it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
GFP_DMA should not be used by itself, it still needs GFP_KERNEL or
such. Fix two occurrences of allocations with GFP_DMA only.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There is a dummy read of a PCI MMIO register that occurs before the SSB bus
has been powered, which is an error. This bug has not been seen earlier,
but was apparently exposed when udev was updated to version 182.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrl to replace
brcmf_sdioh_card_regread as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new interface brcmf_sdio_regr/w provides result of access
attempts. It is no longer necessary to use dedicated variable
and function to provide enquiry for failure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new brcmf_sdio_regrl/regwl interface has already performed
retries on failed attempts. It is no longer necessary to have the
retry mechanism in r_sdreg32/w_sdreg32.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regwl to replace
brcmf_sdcard_reg_write as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrl to replace
brcmf_sdcard_reg_read as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regwb to replace
brcmf_sdcard_cfg_write as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrb to replace
brcmf_sdcard_cfg_read as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both brcmf_sdcard_cfg_read/write and brcmf_sdcard_reg_read/write
are used as interface functions for register access of SDIO WiFi
dongle. A unified interface brcmf_sdio_regr/w is introduced in
this patch in order to simplify the interface and keep the
complexity within the lower layer.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdcard_set_sbaddr_window configures 3 registers on SDIO
function misc bank to change current silicon backplane programming
window. This patch makes it call brcmf_sdioh_request_byte directly
in order to prepare for the write register interface unification.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size parameter for brcmf_sdcard_reg_write is always 4. Remove it
to make the code cleaner.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size parameter for brcmf_sdcard_reg_read is always 4. Remove it
to make the code neat.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes multiple issues with the current RTT
implementation in ath9k.
* The data that is obtained from the RTT interface registers
are stored in 31:5 - mask out the extra bits when reading them.
* A history buffer is maintained which is not needed at all.
Remove this array and just store the baseband data for each
chain (or bank).
* A 'num_readings' variable was being used to handle the
last entry. But it was being used in an improper manner, with
the result that the RTT values were never being written
to the RTT Interface registers. Fix this by using a simple
flag.
* Stop baseband operations before programming the calibration values
to the HW.
* Do not restore RX gain settings as part of RTT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the BA session is torn down before we had a chance to start it
we shouldn't disable the AGG tx queues that weren't enabled.
This can happen in two cases:
1) We get a delBA before we drained our Tx queues in agg start flow
2) We didn't get the (successfull) addBA response on time
Reported-by: Daniel Chyan <dchyan@princeton.edu>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have TX_REPLY for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power index that the user gives as module parameter
in in range 1-5, but we need to decrease it in order
to create an array index out of it (0-4) for the power
table command.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once driver decide to change reduced tx power behavior,
make sure the reduce tx power valid bit is set
Change-Id: I3afae96319292d8cb347a812a948085c5db7ad91
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1948
Tested-by: Jenkins
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In bt coex, consider the average rssi as part of decision making process
Change-Id: I8d11d7f177a6875e2a9d08f7539d42253226fd7a
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1945
Tested-by: Jenkins
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Documentation/CodingStyle says
"Do not unnecessarily use braces where a single statement will do."
Use "switch/case", instead of "if/else_if/else", so that more cases
can be added later.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to report the number of transmission attempts for each rate
as well as to terminate the rate array with -1. The in-kernel datapath
of hwsim simulates a perfect medium, therefore the driver only needs to
report that the first transmission attempt was sucessfully completed at
the most favorable rate.
Rate control is working again for this driver. Tested mesh mode with
minstrel.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dummy0/1/2 names are always used and there are options to set multiple
dummy devices. Remove the obsolete text
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42865
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy reported pch_gbe triggered "NETDEV WATCHDOG" errors.
May 11 11:06:09 kontron kernel: WARNING: at net/sched/sch_generic.c:261
dev_watchdog+0x1ec/0x200() (Not tainted)
May 11 11:06:09 kontron kernel: Hardware name: N/A
May 11 11:06:09 kontron kernel: NETDEV WATCHDOG: eth0 (pch_gbe):
transmit queue 0 timed out
It seems pch_gbe has a racy tx path (races with TX completion path)
Remove tx_queue_lock lock since it has no purpose, we must use tx_lock
instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needs to be tagged with FLAG_WWAN, which since it has generic
descriptors, won't happen if we don't override the generic
driver info.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock before unlink, but may
cause skb traversing races:
- after URB is unlinked and the queue lock is released,
the refered skb and skb->next may be moved to done queue,
even be released
- in skb_queue_walk_safe, the next skb is still obtained
by next pointer of the last skb
- so maybe trigger oops or other problems
This patch extends the usage of entry->state to describe 'start_unlink'
state, so always holding the queue(rx/tx) lock to change the state if
the referd skb is in rx or tx queue because we need to know if the
refered urb has been started unlinking in unlink_urbs.
The other part of this patch is based on Huajun's patch:
always traverse from head of the tx/rx queue to get skb which is
to be unlinked but not been started unlinking.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon resume from standby, there is a possible interrupt
unsafe locking scenario raised when configure the Kernel
with CONFIG_PROVE_LOCKING. So this patch fixes that in
PM driver stuff by calling lock/unlock_irqsave/restore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some coldfire boards (ie m5253demo) have a dm9000 onboard.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under most circumstances, the bitmap allocator does not allocate the
same full 24-bit QP number immediately after a QP is destroyed.
This works by using the upper bits of a 24-bit QP number, beyond the
number of QPs that are actually available in the low level driver.
For example, say that the HCA is willing to allocate a maximum of 64K
qps. We use the bits 23..16 as a "counter" which is incremented by 1
at each allocation so that even if the same physical QP is
re-allocated, it will not receive the same 24-bit QP number.
However, we have seen the following scenario:
1. Allocate, say, 255 QPs in succession. This will cause a wrap of the "counter".
2. Destroy the first QP allocated, then allocate a new QP. The new QP,
because of the counter wraparound, will get the same FULL QP number as
the QP just destroyed!
This is a problem because packets in transit can be erroneously
delivered to the new QP when they were meant for the old (destroyed)
QP, because the full QP number of the new QP is identical to the
destroyed QP. (The "counter" mechanism is meant to prevent this by
having the full 24-bit QP numbers differ even if the physical QP on
the HCA is the same. As we see above, however, this mechanism does
not always work).
The best fix for this problem is to allocate QPs in round-robin mode,
so that the physical QP numbers are not immediately re-used.
Found-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In commit b0302ab, the rtlwifi family of drivers was converted to use
asynchronous firmware loading. Unfortumately, the implementation was
racy, and the ieee80211 routines could be started before rtl_init_core()
was called to setup the data.
This patch fixes the bug noted in https://bugzilla.kernel.org/show_bug.cgi?id=43187.
Reported-by: Joshua Roys <Joshua.Roys@gtri.gatech.edu>
Tested-by: Neptune Ning <frostyplanet@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.3]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current ARM7 Cirrus Logic product line contains only 3 cpu.
EP7312 - Fully functional.
EP7309 - Missing SDRAM interface.
EP7311 - Missing DAI.
It makes no sense to separate the header files to identify these differences,
it is only necessary to keep in mind the presence or lack of any features of
a specific CPU when writing code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8cd ("bonding: don't increase
rx_dropped after processing LACPDUs")
I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.
This inter-diffs such that the warnings are now gone.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new initialization functions and device support
for i210 and i211 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82580 and later parts did not have low power setting functions. This patch
adds the specific functions, pointers and assignments for these low
power settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other values from device provided buffer are byteswapped, so it seems more
logical to do same for these.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other values from device provided buffer are byteswapped, so it seems
more logical to do same for these.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the hyperv filter and rndis gadget driver to use the same command
enumerators as the other drivers and delete the surplus command codes.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802_* network OIDs were duplicated, so let's merge them and
use the RNDIS_* prefixed definitions from the hyperV driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RNDIS protocol contains a vast number of Object ID:s (OIDs).
The current definitions had multiple definitions of these ID:s,
let's use the nicely RNDIS_*-prefixed defines from the HyperV
implementation, rename everywhere they're used, and copy+rename
the few that were missing from this list of objects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RNDIS status codes are redefined with much stranged ifdeffery
and only one of these codes was used in the hyperv driver, and
there it is very clearly referring to the RNDIS variant, not some
other status. So clarify this by explictly using the RNDIS_*
prefixed status code in the hyperv drivera and delete the
duplicate defines.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a first step to consolidate the RNDIS implementations, break out
a common file with all the #defines and move it to <linux/rndis.h>.
This also deletes the immediate duplicated defines in the
<linux/rndis.h> file that yields a lot of compilation warnings.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file <linux/usb/rndis_host.h> used a number of #defines
that included the cpu_to_le32() macro to assure the result will be
in LE endianness. Inlining this into the code instead of using it
in the code definitions yields consolidation opportunities later
on as you will see in the following patches. The individual
drivers also used local defines - all are switched over to the
pattern of doing the conversion at the call sites instead.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_OF_MDIO is tristate and will be m if PHYLIB is m. Use
IS_ENABLED macro to prevent build error:
ERROR: "of_mdio_find_bus" [drivers/net/phy/mdio-mux.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shawn Guo <shawn.guo@linaro.org> writes:
mxs common clk porting for v3.5. It depends on the following two branches.
[1] git://git.linaro.org/people/mturquette/linux.git clk-next
[2] http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm.git clkdev
As the mxs device tree conversion will constantly touch clock files,
to save the conflicts, the updated mxs/dt branch coming later will
based on this pull-request.
* 'clk/mxs' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: remove now unused timer_clk argument from mxs_timer_init
ARM: mxs: remove old clock support
ARM: mxs: switch to common clk framework
ARM: mxs: change the lookup name for fec phy clock
ARM: mxs: request clock for timer
clk: mxs: add clock support for imx28
clk: mxs: add clock support for imx23
clk: mxs: add mxs specific clocks
Includes an update to Linux 3.4-rc6
Conflicts:
drivers/clk/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.
Done via cocci script:
$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
- !compare_ether_addr_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- compare_ether_addr_64bits(a, b)
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) == 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) != 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) == 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) != 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling pci_disable_sriov() while VFs are assigned to VMs causes
kernel panic. This patch uses PCI_DEV_FLAGS_ASSIGNED bit state of the
VF's pci_dev to avoid this. Also, the unconditional function reset cmd
issued on a PF probe can delete the VF configuration for the
previously enabled VFs. A scratchpad register is now used to issue a
function reset only when needed (i.e., in a crash dump scenario.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.
Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.
Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.
The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the caller (PM resume code) is not the one holding rtnl, when taking the
'else' branch rtnl may be released at any moment, thereby defeating the whole
purpose of this code block.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have an OMAP prefix on these SoCs that are in the family
but arent' really called OMAP.
Simple rename: CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
No functional change.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated for the driver config change also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update version number to better match the version of the out of tree
driver with similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the hwmon code was initially added it was with the assumption that a
sysfs patch would be also coming soon. Since that isn't the case some
clean up needs to be done. This patch does that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the MAC, in order to provide the best software
timestamps. This patch adds this call for that support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the ethtool get_ts_info operation, which enables
access of available timestamp/timesync support for that device. It can query
which ptp clock device is associated with the particular port.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current value of the udelay timeout for ixgbe_disable_rx_buff is too
short. This causes the security path to not not be properly disabled during
the section that is meant to have it turned off. The end result causes a race
condition that results in RX issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.
The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.
This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.
Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.
Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF sends a MACVLAN request with index of zero then it is not
actually trying to add a filter. Check the index value and only
indicate that operation is not allowed when the VF is actually trying
to add a filter.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present. This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work. By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the logic in the priority based flow control
configuration routines. Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.
In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we would get a mailbox error and still process the message.
Instead we should exit on error.
In addition we should also be flushing the ACK of the message so that we
can guarantee that the other end is aware we have received the message
while we are processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current igb outputs registers related to TX/RX queues(ex. RDT, RDH, TDT, TDH).
But it thinks the number of RX/TX queues is 4. But 82576 has 16 RX/TX queues.
This patch modifies igb to output the rest of the registers if the device is
82576.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Acked-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver queries DIMM information from firmware and accordingly
sets "presence" field of the structure.
"presence" field when set to 0xff denotes invalid flag. And when
set to 0x0 denotes DIMM memory is not present.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable fw dump by default at start up.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently allows for SFP+ eeprom to be returned using the ethtool API.
This can be extended in future to handle different eeprom formats
and sizes
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh: Drop redundant validation, comment, whitespace]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Previously we refilled with much larger batches, which caused large latency
spikes. We now have many more much much smaller spikes!
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We need to clear the private data pointer in the PCI device.
Also reorder cleanup in efx_pci_remove() for symmetry.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_nic_fatal_interrupt() disables DMA before scheduling a reset.
After this, we need not and *cannot* flush queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.
To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.
Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
{
.start = GPIO_BRCMF_SDIO_OOB_NUM,
.end = GPIO_BRCMF_SDIO_OOB_NUM,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}
};
struct platform_device brcmf_sdio_device = {
.name = "brcmf_sdio_pd",
.id = -1,
.num_resources = ARRAY_SIZE(brcmf_sdio_res),
.resource = brcmf_sdio_res,
};
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For out of band interrupt which is going to be introduced shortly,
the interrupt register function must be called after firmware is
downloaded. This patch moves it from brcmf_sdbrcm_probe to
brcmf_sdbrcm_bus_init.
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bus state should be the correct flag for bus status. Use it instead
of result from previous function call for backplane clock switch.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus.
Stop releasing and claiming host in irq handler to eliminate
any potential risk.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Reported-by: Cesare Leonardi <celeonar@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a register to be unspecified, therefore not creating its debugfs
file entry.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.
drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy). The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.
The current code works fine because mib_phy structs are larger than
mib_local structs. But we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't make any sense. Init it from the transport instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Also remove a debug print when allocation error occurred.
The kernel will complain anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens