When an interface is brought up, the recent changes
to allow changing type-while-up only set the running
bit after everything was done. This broke a number
of things, including idle calculation for monitor
interfaces, and it also broke WDS station insertion
(although nobody noticed yet).
Thus, change the code to set the running bit earlier,
but keep it after the driver's add_interface was
called because otherwise drivers may iterate over
interfaces they haven't fully set up yet.
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is modifying the station flags, and
as such should hold the flags lock so it can
do so atomically vs. other flags modifications
and readers. This issue was introduced when
this code was added in eccb8e8f, as it used
the wrong lock (thus not fixing the race that
was previously documented in a comment.)
Cc: stable@kernel.org [2.6.31+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The output becomes:
[ 41.261941] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_info_get_bss() is used to match STA pointers
for VLAN/AP interfaces, but if the same station
is also added to multiple other interfaces it
will erroneously match because both pointers are
NULL, fix this by ignoring NULL pointers here.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hdr pointer is left dangling after call to ieee80211_skb_resize. This
can cause guards around mesh path selection to fail.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a path in nl80211_set_wiphy where result is tested but
uninitialized.
I am hitting this path when I attempt:
sh# iw dev wlan0 set channel 10
command failed: Unknown error 1069727332 (-1069727332)
Signed-off-by: William Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace sizeof(rtap_namespace_sizes) / sizeof(rtap_namespace_sizes[0])
with ARRAY_SIZE(rtap_namespace_sizes) in net/wireless/radiotap.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise the hardware scan handler could access an invalid scan request
structure. The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function exists to clean-up after a hardware error or something
similar. The restart is accomplished using the same infrastructure used
to resume after a suspend. The suspend path cancels running scans, so
it seems appropriate to do that here as well for software-based scans.
If a hardware-based scan is pending, issue a warning message since this
indicates that the drivers has failed to clean-up after itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same expression is tested twice and the result is the same each time.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal strength value in a single RX frame is not that reliable,
so it is better to delay start of CQM events until there is a real
average signal strength from more than a single Beacon frame
available.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ave_beacon_signal value uses 1/16 dB unit and as such, must be
initialized with the signal level of the first Beacon frame multiplied
by 16. This fixes an issue where the initial CQM events are reported
incorrectly with a burst of events while the running average
approaches the correct value after the incorrect initialization. This
could cause user space -based roaming decision process to get quite
confused at the moment when we would like to go through authentication
and DHCP.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Somebody noticed this problem, and I outlined
to them how to fix it, but haven't heard back
from them. So while I was adding the state
field I figured I could use it to fix it.
The problem, as I understand it, is that when
we go offchannel while the driver has a queue
stopped, the driver will likely start draining
the queue and then enable it while offchannel.
This in turn will enable the interface queue,
and that leads to transmitting data frames on
the wrong channel.
Fix this by keeping track of offchannel status
per interface, and not enabling the interface
queues on interfaces that are offchannel when
the driver enables a queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the concurrent virtual interface checks
into a new function that can be used to check
for any given new interface type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas_tf special code for zero addresses
is a bit too complex, it compares against a stack
value instead of using is_zero_ether_addr() and
tries to update all interfaces even if just the
one that's being brought up needs to be changed.
Additionally, the repeated check for a valid MAC
address need only be done if we actually changed
it on the fly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of ieee80211_sdata_running(),
some new code was introduced that uses netif_running()
instead. Switch all these instances over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a lot of redundant code in mac80211's
interface cleanup/down, for example freeing
AP beacons is done both when the interface is
set DOWN as well as when it is torn down, of
which only the former has any effect.
Also, a bunch of things should be closer to
where they matter, like the MLME timers that
we should cancel when disassociating, rather
than only when the interface is set DOWN.
Clean up all this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are subqueue helpers so that we don't
need to get the TX queue and then wake/stop
it, use those helpers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 currently rejects all cipher suites it
doesn't know about for key length checking
purposes. This can lead to inconsistencies when
a driver advertises an algorithm that cfg80211
doesn't know about. Remove this rejection so
drivers can specify any algorithm they like.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_scan_completed() function was a frequent
source of potential deadlocks, since it is called by
drivers but may call back into drivers, so drivers had
to make sure to call it without any locks held, which
frequently lead to more complex code in drivers. Avoid
that problem by allowing the function to be called in
any context, and queueing the actual work it does.
Also update the documentation for it to indicate this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since cfg80211 manages the BSS list completely,
this define hasn't been used for a long time
and will never be used again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a mac80211-based driver advertises mesh mode
support, this will be advertised to userspace.
However, if mac80211 was compiled without mesh
support, then that won't actually be true. Fix
this by removing the bit for mesh if mesh isn't
compiled in.
Since this synchronizes what we advertise to
cfg80211 and actually support, it means we can
now rely on cfg80211's interface type checks
and need not check again in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a potential crash (null-pointer de-
reference) which was introduced in my previous patch:
"mac80211: AMPDU rx reorder timeout timer"
During a BA teardown, the pointer to the soon-to-be-gone
tid_ampdu_rx element will be nullified. Therefore the
release timer mechanism has to be careful not to
accidentally access the item without any RCU protection.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 95a6ccbb46c70cff376684c752831c014c87029d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Aug 12 15:38:38 2010 +0200
cfg80211/mac80211: extensible frame processing
introduced a netlink bug that caused parsing errors
in userspace because it forgot to close a nesting,
which would advertise a nesting length of zero to
userspace, which then completely threw off parsing
and led to
Illegal nla->nla_type == 0
being printed by libnl.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unlike most other workqueue-tasks, the restart_work is
not scheduled onto mac80211's private per-interface
workqueue, but onto one of the system-wide workqueues.
Therefore the mac80211-stack has to cancel any pending
restarts, before destroying the shared device context
and handing back the memory. Otherwise - under very
unlucky circumstances - there could be a stale work-
item left, because some other kernel component might
have delayed the execution of ieee80211_restart_work
for too long.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_hdr only used when CONFIG_MAC80211_MESH is defined
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is disabled, action frames will not
be encrypted since they are management frames
and the only management frames that can then
be encrypted are authentication frames.
Therefore, setting the don't-encrypt flag on
action frames is unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function analyses only its single, value-passed
argument, and has no side effects. Thus it can be
const, which makes mac80211 smaller, for example:
text data bss dec hex filename
362518 16720 884 380122 5ccda mac80211.ko (before)
362358 16720 884 379962 5cc3a mac80211.ko (after)
a 160 byte saving in text size, and an optimisation
because the function won't be called as often.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When shared key auth is requested, cfg80211
should verify that the device is capable of
WEP crypto which is required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WEP is unavailable, don't advertise it
to cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The decryption code verifies whether or not
a given frame was decrypted and verified by
hardware. This is unnecessary, as the crypto
RX handler already does it long before the
decryption code is even invoked, so remove
that code to avoid confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to keep separate if statements
for setting up the CCMP/AES-CMAC tfm structs;
move that into the existing switch statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable using network namespaces with
wireless devices even when sysfs is
enabled using the same infrastructure
that was built for netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP sends a deauth frame, or we send one
to an AP, that only means we lost our connection
if we were actually connected to that AP. Check
this to avoid sending spurious "disconnected"
events and breaking "iw ... link" reporting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new timer, which will release
queued-up MPDUs from the reorder buffer, whenever
they've waited for more than HT_RX_REORDER_BUF_TIMEOUT
(which is at around 100 ms).
The advantage of having a dedicated timer, instead of
relying on a constant stream of freshly arriving aMPDUs
to release the old ones, is particularly observable when
even a small fraction of MPDUs are forever lost at
low network speeds.
Previously under these circumstances frames would become
stuck in the reorder buffer and the network stack of both
HT peers throttled back, instead of revving up and
gunning the pipes.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a few stale parameters and variables
which survived the last, large rx-path reorganization:
"mac80211: correctly place aMPDU RX reorder code"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes the reorder logic from the RX path and
moves it into separate routines to make the expired frame
release accessible.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_add_key() currently returns -ENOMEM in case of any error,
including a missing crypto algorithm. Change ieee80211_key_alloc()
and ieee80211_aes_{key_setup_encrypt,cmac_key_setup}() to encode
errors with ERR_PTR() rather than returning NULL, and change
ieee80211_add_key() accordingly.
Compile-tested only.
Reported-by: Marcin Owsiany <porridge@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
