Remove MPU-timer based sched_clock() in favor of the common one based
on 32k sync timer which works across all OMAP1/2/3 platforms.
Using 32k based one also gives a valid sched_clock() very early in the
boot process.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer used and similar conversions are provided
by the clocksource/clockevent code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Start cleaning up GPIO handling for OMAP5912 OSK board:
- Initialize GPIOs using the cross-platform calls, not the old
OMAP-private ones.
- Move touchscreen setup out of ads7846 code into board-specfic
setup code, where it belongs.
This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes misprints in ITE 8152 interrupt demuxing
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ccoreutils and other have started using fstatat64. Thus, we
need a shim for it if we want to support modern oldabi
userlands (such as Debian/arm/lenny) with EABI kernels.
See http://bugs.debian.org/462677
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix signal return code when enable CONFIG_OABI_COMPAT
Signed-off-by: Janboe Ye <janboe.ye@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_MAX is the number of the last gpio, not the number of gpios. So
the bitmap must provide GPIO_MAX + 1 bits.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definitions of ATAG_CORE and ATAG_CORE_SIZE in head.S to
head-common.S. There is no use of these in head.S itself, but they
are used in head-common.S. When building for the !CONFIG_MMU case
these were not defined when compiling head-nommu.S (which includes
head-common.S).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DNS-323, Kurobox-Pro / Linkstation-Pro, QNAP TS-109/TS-209 and some
other orion-based systems have several bogus memory entries in the tag
table, which causes the system to crash at startup. Ignore them by
resetting the tag ID to 0 in a machine fixup function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows monitoring compile issues with Kautobuild for
other omap1 boards until we have more board specific defconfig
files.
After 2.6.25, we can add a generic config_omap_generic16xx to
compile in support for all 16xx boards and then remove other
boards from OSK defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build fix:
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:720: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
H2 and H3 were broken on by e27a93a944,
which removed declarations for their tps6501x chips. This resolves
that issue for the H2. (Note that this patch *also* broke the isp1301
support on H2; it presumed a not-yet-merged new-style I2c driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of build warnings and errors in mainline for H3 boards; not
all the H3 updates were correct, it seems like the OMAP1 boards are
not getting proper build testing.
Also, commit e27a93a944 introduced a
regression related to the tps65013 chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes parameter passing to DMA handlers uniform between non-chained
and chained transfers and makes debugging easier. Additional data like
chain_id can be always passed to handlers via callback data if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Lindgren