This patch moves the sanity check on beacon interval
which was done only for mesh mode to all operating
modes just to be safe.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like mac80211 can request the driver to start beaconing with
a beacon interval of zero in some cases (at least for mesh point). This
does not sound correct and something may need to be fixed in
mac80211. However, taken into account the unpleasantness of getting
stuck in an infinite busy loop with rtnl_lock held, let's add a quick
workaround in the driver to avoid the worst symptom while someone more
familiar with the mesh implementation can figure out what should be done
with mac80211 as far as beacon interval configuration is concerned.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I have a TrendNet 652-BRP running OpenWRT + ath9k very well. The only
problem is that the beacon gets stuck maybe once a day. After
Vasanthakumar Thiagarajan's "ath9k: cleanup beacon parameters
configuration" patch, ath9k would nearly re-configure the beacons after it
detected the stuck beacon, and did a reset. But it would fail the
SC_OP_TSF_RESET check in ath_beacon_config_ap. This patch gets the beacon
fully reconfigured after the reset.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.
In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86 this allows us to do the following small savings:
shave off 23 % off of the module's data, and
shave off 6 % off of the module's text.
We save 456 bytes, for those counting.
$ size ath9k.ko
text data bss dec hex filename
250794 3628 1600 256022 3e816 ath9k.ko
$ size ath9k-old.ko
text data bss dec hex filename
239114 15308 1600 256022 3e816 ath9k-old.ko
$ du -b ath9k.ko
4034244 ath9k.ko
$ du -b ath9k-old.ko
4033788 ath9k-old.ko
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
