remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/mtx-1/board_setup.o
{standard input}: Assembler messages:
{standard input}:263: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:274: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:296: Error: opcode not supported on this processor: mips1 (mips1) `sync'
[...]
Any .set mipsX statement other than .set mips0 at the end of inline
assembler is a big fat bug.
Introduced by 9482eabeca315c0276ffb50026b7482481b7097b (linux-mips.org) rsp.
32fd6901a6 (kernel.org).
While at it, fix the same issue in
arch/mips/alchemy/devboards/pb1000/board_setup.c
arch/mips/alchemy/xxs1500/board_setup.c
as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a regression introduced by commit "MIPS: Alchemy: MTX-1:
Use linux gpio api." (bb706b28bb) which broke
PCI bus operation. The problem is caused by alchemy_gpio2_enable() which
resets the GPIO2 block. Two PCI signals (PCI_SERR and PCI_RST) are connected
to GPIO2 and they obviously do not to like the reset. Since GPIO2 is
correctly initialized by the boot monitor (YAMON) it is not necessary to
call this function, so just remove it.
Also replace gpio_set_value() with alchemy_gpio_set_value() to avoid
problems in case gpiolib gets initialized after PCI. And since alchemy
gpio_set_value() calls au_sync() we don't have to au_sync() again later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
To: linux-mips@linux-mips.org
To: manuel.lauss@googlemail.com
Patchwork: https://patchwork.linux-mips.org/patch/1448/
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is not always used, even if it is available.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
