CONFIG_VIDEO_BUF_DVB became CONFIG_VIDEOBUF_DVB.
But in these cases, it makes more sense to use CONFIG_VIDEO_SAA7134_DVB
or CONFIG_VIDEO_CX88_DVB_MODULE depending on the driver.
The reference in cx23885.h should just be removed, as the code there needs to
be included if DVB is on or off. I do not think you can even compile the
cx23885 driver without DVB. It's clearly just leftover from when the file was
obvious copied from the cx88 driver (which is not mentioned in the copyright
BTW).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCI-dependent videobuf_foo methods were renamed as videobuf_pci_foo.
Also, videobuf_dmabuf is now part of videobuf-dma-sg private struct.
So, to access it, a subroutine call is needed.
This patch renames all occurences of those function calls to be
consistent with the video-buf split.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
IR workqueue should be disabled during suspend. This avoids some troubles, like
the one reported on bug #8689:
"The Hauppauge HVR 1100 ir-remote control does not work after resume from
suspend to ram or disk."
This patch disables IR before suspending, re-enabling it after resume.
Thanks to Peter Poklop <Peter.Poklop@gmx.at> for reporting it and helping with
the fix.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reviewed-by: Peter Poklop <Peter.Poklop@gmx.at>
Not sure why they are there, but they don't do anything now.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the balance control to make the mono volume control stereo.
Note that full range isn't supported. The balance control attenuates one
channel by 0 to -63 dB, and the volume control provides additional attenuation
to both channels by another 0 to -63 dB.
So the channel with the most attenuation has a range of 0 to -126 dB, while
the other channel only has a range of 0 to -63 dB. ALSA volume controls don't
appear to support this concept. I just limited the range to 0 to -63 total.
Once you get to -63 dB, you're already at silence, so additional attenuation
is pretty much pointless anyway.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-load ir-kbd-i2c for ir receiver support, and rtc-isl1208 for rtc
support for the FusionHDTV5 RT Gold.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were many instances of 7-space indents spread throughout
the v4l-dvb tree.
This patch replaces the 7-space indents with tabs. The whitespace cleaner
script doesn't catch these, because it assumes that all indents are 8-space.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver should now pass the 'busy' state of the device to the cx2341x
module whenever controls are set or tried. -EBUSY will be returned if
the device is busy and the user attempts to modify certain 'dangerous'
controls. It concerns controls that change the audio or video
compression mode and bitrates.
The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy)
to the cx2341x, effectively keeping the old behavior for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver has long claimed to support mmap, but it didn't work at all. Some
of the dma buffer parameters weren't set, and since video_buf uses vmalloc to
allocate the buffer, a page callback is needed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver kepts a static global array of snd_card pointers for each card
probed, which was never used.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework the way the DMA buffer is handled and IRQs are generated.
ALSA uses a ring-buffer of multiple periods. Each period is supposed to
corrispond to one IRQ.
The existing driver was generating one interrupt per ring-buffer, as opposed
to per period. This meant that as soon as the IRQ was generated, the hardware
was already starting to re-write the beginning of the buffer. Since the DMA
happens on a per-line basis, there was only a narrow window to copy the data
out before the buffer was overwritten.
The cx88 core RISC program generator is modified so that it can set the IRQ
and counter flags to count every X lines of DMA transfer. This way we can
generate an interrupt every period instead of every full ring-buffer. Right
now only period of one line are supported, but it should be possible to
support longer periods. Note that a WRITE instruction generates an IRQ when
it starts, not when the transfer is finished. Thus to generate an IRQ when
line X is done, one must set the IRQ flag on the instruction that starts line
X+1, not the one that ends line X.
Change the line size so that there are four lines in the SRAM FIFO. If there
are not four lines, the analog output from the cx88's internal DACs is full of
clicks and pops.
Try to handle FIFO sync errors. Sometimes the chip generates many of these
errors before audio data starts. Up to 50 sync errors will be ignored and the
counter reset.
Have the IRQ handler save the RISC counter to the chip struct, and then have
the pointer callback use this to calculate the pointer position. We could
read the counter from the pointer callback, but sometimes the sync errors on
start up cause the counter to go crazy. ALSA sees this and thinks there has
been an overrun. The IRQ hander can avoid saving the counter position on
sync errors.
The chip "opened" flag wasn't necessary. ALSA won't try to open the same
substream multiple times. Probably this code was cut&pasted from the bt87x
driver, which has multiple sub-streams for one chip.
Do error checking for the videobuf mapping functions.
snd_card_cx88_runtime_free() is useless and can be deleted.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The revision is part of the pci_dev struct, so there is no need to read it in.
Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.
linux/pci.h wasn't included. It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
channels_min should be 2, not 1. The hardware only supports stereo.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get. One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on. Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.
Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on. However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug). The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.
Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an irq handled by the cx88 core driver (currently IR and errors) occurs
and the cx88-alsa irq handler is the first called, it will claim to have
handled the irq but it doesn't call cx88_core_irq() to handle it.
The means loading cx88-alsa can disable the IR remote.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used for the PCI_INTMSK and PCI_INT_STAT registers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise. The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.
However, the "no deemphasis" setting doesn't work. On my chip, cx23883, it
produces the same result as the 75 us time constant. Maybe the default
settings on the cx23881 are for 50 us?
Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the "CORE" prefix from cx88 printks. It was only used a few times,
and it makes it look like they're coming from the kernel core or something.
Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it. Get rid of the addresses, which are always
wrong. The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.
In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.
Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.
The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.
A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized. Moving that task to cx88-cards makes the
driver simpler and the files more self contained.
- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
moved out of cx88-core.c:cx88_get_core() and into a new function in
cx88-cards.c, cx88_core_create(). This makes both functions simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx88 driver state stored the ID of the board type in core->board. Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.
This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information. This allows
access to board information without the extra indirection. e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.
This has a number of advantages:
- The code is simpler to write.
- It compiles to be smaller and faster, without needing the extra array lookup
to get at the board information.
- The cx88_boards array no longer needs to be exported to all cx88 modules.
- The boards array can be made const
- It should be possible to avoid keeping the (large) cx88_boards array around
after the module is loaded.
- If module parameters or eeprom info override some board configuration
setting, it's not necessary to modify the boards array, which would
affect all boards of the same type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An error message for PCI resource allocation failure used the board type
before it was set. Just get rid of the error message, as get_ressources()
[sic] already prints one. Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux setting is only two bits, but was taking up a whole 32
in the input description struct. By changing it to a two-bit
bitfield, it can fit in what was padding space before and drop
the input size by 4 bytes, from 28 to 24. This drops the board
description struct, which has 9 inputs, from 280 to 244 bytes.
Total driver size decreases by 2108 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the advanced debug functions to the radio videodev template. One could
already use them from the video and vbi devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up duplicate includes in
drivers/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bug: With a hardware encoder board installed as cx88[1] and a
non-encoder boards installed as cx88[0], an OOPS is generated
during cx8802_get_device() called from mpeg_open().
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch adds checking of kthread_run return code and issues a message
if it fails.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in cx88-i2c and cx88-vp3054-i2c.
For one thing, a real template is supposed to be read-only. And in some
cases it's more efficient to initialize the few fields we need
individually.
This clean-up shrinks cx88-i2c.o by 33% and cx88-vp3054-i2c.o by 49%
(x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the function, cx88_ir_handle_key:
- convert nested if statement to a switch..case block
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add support for the I2C based IR transceiver of the Hauppauge HVR-1300
- remove bad code from cx88-input.c
Signed-off-by: Jan Frey <jfrey@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Closes the issue opened on Kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=8383
There's no need to print timeout without debug turned on:
Apr 27 23:02:14 video kernel: cx88[1]/2-mpeg: cx8802_timeout
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following two pointers in struct cx8802_dev are unused - remove them:
void* fe_handle;
int (*fe_release)(void *handle);
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that cx88-blackbird is only accepting the official firmware image,
we no longer have any need to store the size of the firmware inside the
cx88 data structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove temporary support for older 256 kB firmwares.
ivtv, pvrusb2 and blackbird can now all handle the newer larger firmwares,
so support for the older (buggier) firmware can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor at mail.ru>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that dvb-pll is being used properly in all cx88-dvb instances,
the cx88 driver no longer needs to store pll_desc nor pll_addr.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.
The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point. This the recommended value for
DVB-T operation.
The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).
The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.
CX88_BOARD_HAUPPAUGE_HVR1100 Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000 Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300 Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod
This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence. The non-dvb-pll code for this
user is removed.
X88_BOARD_DNTV_LIVE_DVB_T_PRO digitalnow DNTV Live! DVB-T Pro
In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:
SAA7134_BOARD_MD7134 Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID Asus Europa2 OEM
The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.
This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.
For the cxusb driver, only one board is effected:
USB_PID_MEDION_MD95700 Medion MD95700
This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively. These functions are effectively the same
as the dvb-pll versions. They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does). This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.
The functionality is added to dvb-pll, where all the other code that
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link. Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.
It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).
It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v4l-info and other programs would loop indefinitely while querying the
tuners for cx88-blackbird cards.
The cause was that vidioc_g_tuner didn't return an error value for
qctrl->id != 0, making the application think there is a never ending
list of tuners...
This patch adds the same index check as done in vidioc_g_tuner() in
cx88-video.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the generic client declared in cx88-vp3054-i2c: it's not used
anywhere. This shrinks cx88-vp3054-i2c.o by 29% on x86_64. Unless it
was there for later use?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha:
drivers/media/video/cx88/cx88-video.c: In function 'cx8800_initdev':
drivers/media/video/cx88/cx88-video.c:1782: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
drivers/media/video/cx88/cx88-video.c:1782: error: (Each undeclared identifier is reported only once
drivers/media/video/cx88/cx88-video.c:1782: error: for each function it appears in.)
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the S-Video and CVBS (composite) analog video inputs
of the Leadtek WinFast DTV1000 T adapter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88_print_irqbits were expecting a string pointer with 32 bytes. Better
to pass the string size and use ARRAY_SIZE on its calls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATI HDTV Wonder needs to initialize some registers before allowing the
tuner to start working.
The current logic have lots of magic. This patch makes the code cleaner,
using ARRAY_SIZE() for the initialization array and using a
bidimensional array, instead of doing some stuff like:
&buffer[i+2]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attach code for HAUPPAUGE_HVR3000 and HAUPPAUGE_HVR1300 is exactly
the same as the code used by HAUPPAUGE_HVR1100, HAUPPAUGE_HVR1100LP, and
WINFAST_DTV2000H. So, those first two cards are added to the case block
used by the last three.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ADS Tech InstantTV DVB-S is a clone of the KWorld DVB-S 100.
This patch adds autodetection support for this card based on
pci subsystem id.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The code of the dvb-pll driver and the lgh06xf driver is nearly
identical. The main difference is that the lgh06xf driver would set the
AGC TOP value on every tune call. The dvb-pll driver now has the ability
to set the AGC TOP when the front-end device is opened, which is a better
way to go about it. By using this ability of dvb-pll, the lgh06xf driver
is made unnecessary.
There is one other difference. dvb-pll will probe for the presence of an
I2C pll chip by doing a one byte read, the lgh06xf driver did not do
this. In some devices the PLL is not reachable over I2C at the timer the
tuner is attached. Some more initialization, such as firmware loading,
must take place first. None of the devices using a LG-H06xF should have
this problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for loading cx88-dvb and cx88-blackbird
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
added support for deferred module requesting to cx88
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip matching in struct v4l2_register for VIDIOC_DBG_G/S_REGISTER
was rather primitive. It could not be extended to other busses besides
i2c and it lacked a way to.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the unused struct radionorms.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The out of tree v4l-dvb build system didn't always override the kernel's
configuration settings with v4l-dvb's settings correctly. To work around
this, makefiles would define some new macro based on the setting of a
config variable. e.g. the pwc Makefile would define CONFIG_PWC_DEBUG if
CONFIG_USB_PWC_DEBUG (which is defined via Kconfig) was set.
The v4l-dvb build system should now always override correctly, and this
is no longer necessary. This patch gets ride of these extra defines and
just uses the CONFIG_* settings directly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for these ioctls to the video_ioctl2 system and the cx88
driver.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds support for the combined S-Video/Composite input of the
Terratec Cinergy 1400 DVB-T.
Signed-off-by: Heiko Baums <heiko@baums-on-web.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The video_ioctl2 conversion replaced the default from NTSC to PAL_BG.
This broke cx88-blackbird. Probably, there are some badness at this
driver, not doing all required stuff to change video standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch finishes cx88-blackbird conversion to use video_ioctl2. Video
standards are generated automatically inside videodev.c. the big ioctl
parser is removed, using, instead, video_ioctl2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l2_tvnorm were meant to describe video standards and its names to V4L2 API.
However, this were doing by some static structures at the driver.
This patch changes the internals in a way that, at the driver, only a
v4l2_tvnorm (a 64 bit integer) should be filled, with all supported
tvnorms. videodev will dynamically generate the proper API array
based on supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_ioctl2 handler provides V4L2 API parsing.
Using it makes the driver simpler, and isolates API parsing.
This allows future reusage of driver controls using other ways, like sysfs
and/or procfs and increases isolation of driver-specific handling from the
generic common ioctl processing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some long time unused code under some media driver source files.
There's no need of keeping it at mainstream.
Those unused code will remain available at V4L/DVB master tree and also at
kernel history.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suspending with the cx88xx module loaded causes the system to lock up
because the cx88_audio_thread kthread was missing a try_to_freeze()
call, which caused it to go into a tight loop and result in softlockup
when suspending. Fix that.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
reference to .init.text: from .text between 'cx88_card_setup'
(at offset 0x68c) and 'cx88_risc_field'
Caused by leadtek_eeprom() being declared __devinit and called from
a non-devinit context.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On cx88 driver, sampling rate should be at chroma subcarrier freq (FSC).
However, driver were programming wrong values for PAL/60, PAL/Nc and
NTSC 4.43. This patch do the proper calculation. It also calculates
htotal, hdelay and hactive constants, according with the sampling
rate.
It is tested with PAL/60 by Piotr Maksymuk and Olivier. Also tested with
the already-supported standards.
Test is still required for PAL/Nc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix OMAP clock prescaler to match the comment
i2c: Refactor a kfree in i2c-dev
i2c: Fix return value check in i2c-dev
i2c: Enable PEC on more i2c-i801 devices
i2c: Discard the i2c algo del_bus wrappers
i2c: New ARM Versatile/Realview bus driver
i2c: fix broken ds1337 initialization
i2c: i2c-i801 documentation update
i2c: Use the __ATTR macro where possible
i2c: Whitespace cleanups
i2c: Use put_user instead of copy_to_user where possible
i2c: New Atmel AT91 bus driver
i2c: Add support for nested i2c bus locking
i2c: Cleanups to the i2c-nforce2 bus driver
i2c: Add request/release_mem_region to i2c-ibm_iic bus driver
i2c: New Philips PNX bus driver
i2c: Delete the broken i2c-ite bus driver
i2c: Update the list of driver IDs
i2c: Fix documentation typos
This function should not be in the card-specific area of the file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are five cx22702_config structs used by cx88-dvb, only two of which
are unique. This patch removes the duplicates and sets each card to use
one of the two remaining config structs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Converted DViCO FusionHDTV Hybrid to use dvb_pll_attach, removing
another static dependency of cx88-dvb on dvb-pll.
Acked-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since we're using dvb_pll_attach now, we dont have to populate
dev->core->pll_addr or dev->core->pll_desc anymore.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was a still a pre-dvb-pll set_params function for the lgdt3302 in
the cx88-dvb driver. This patch removes that function and uses
dvb_pll_attach() for the cards that were using it (Dvico FusionHDTV 3
GOLD {Q,T}). This way the set_params function from dvb-pll is used.
dvb_attach() is in turn used on dvb_pll_attach(), eliminating some static
dependencies on dvb-pll. There are still a couple static dependencies on
dvb-pll remaining.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also sprinkled some input_sync() throughout the code.
Acked-by: Ricardo Cerqueira <v4l@cerqueira.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch creates a new atsc tuner module for the LG TDVS-H06xF ATSC tuners,
called lgh06xf. The purpose of this change is to reduce some duplicated
code, and to allow the lgh06xf tuner code to take advantage of dvb_attach().
As a side effect, the dependency of dvb-bt8xx on dvb-pll has been removed,
since the lgh06xf module itself will use dvb-pll, while remaining optional
for the dvb-bt8xx driver through the use of DVB_FE_CUSTOMISE
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add subvendor/device of the ADSTech Instant TV Deluxe PTV-305 to the
card list as card=45 (KWORLD_HARDWARE_MPEG_TV_XPERT).
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allows 'debug=1' for cx88-blackbird module (dev needs to be valid for
dprintk). Fixes a null-pointer dereference when using debug=1.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For the ASUS PVR-416, the external adc must be used for
the rca audio inputs, but television / radio inputs use
the internal adc.
Thanks to Alex Deucher for lending his card to me.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For the KWorld HardwareMpegTV XPert, the external adc must be used for
svideo / composite inputs, but television / radio inputs use the internal adc.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cx88-blackbird boards use an external adc, but not necessarily
for all inputs. Thus, this needs to be configurable on the card level
for each input.
This patch allows for the usage of the external adc to be determined
by a bit setting in the cx88_input struct for cards based on the cx88
blackbird design.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the last cx88 board probed is not backbird based, and a previous board was,
the entire module is unloaded leading to an oops during mpeg_open on the
first /dev/videoN device.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A bug in cx8802_get_driver() meant that in multiboard environments, when testing
frontends on the non primary board, the incorrect device was returned resulting
in "Unsupported value in .mpeg.." messages. Depending on the electrical design
of the hardware (serial, parallel, rising/falling edge detect), transport would
still be delivered and the problem went unnoticed.
This patch ensures the correct instance of cx8802_dev is returned.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A series of patches to change the cx88 framework to allow the
PCI mpeg port to be shared dynamically between different
types of drivers or applications. This patch changes the cx88-dvb
and cx88-blackbird drivers to become 'sub drivers' of a higher
single cx88-mpeg driver.
The cx88-mpeg driver is a superset of the previous cx88-mpeg/blackbird
drivers and now owns the IRQ. cx88-dvb/blackbird now become mini drivers,
registering themselves with cx88-mpeg through a standard interface with
callbacks.
Sub drivers request access to hardware via the cx88-mpeg driver. In turn
the cx88-mpeg driver determines whether the hardware is busy and accepts
or refuses the request, grant access using callbacks into the sub drivers.
The net effect is that you are no longer able to tamper with the mpeg port
from multiple different applications at the same time, potentially breaking
a live mpeg2 hardware encoding or dvb stream.
The mechanism extends to enable multiple dvb frontends to be registered
and share the single resource.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the advanced debugging ioctls, to allow access to the
cx88 registers from userspace. Only i2c_id == 0 is supported, for access
to the cx88 adapter itself. There isn't any support for access to I2C
clients of the adapter. Most of them don't have R/W registers anyway,
and its necessary to use i2c-dev to talk to them from userspace.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fix remote control on WinFast 2000XP Expert by setting timing back to 1 ms,
like it was in the original patch by Robert Reid.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The WinTV-HVR3000 is currently defined for analog support only. This
patch adds full DVB-T support. (DVB-S support will be added soon)
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (39 commits)
Add missing maintainer countries in CREDITS
Fix bytes <-> kilobytes typo in Kconfig for ramdisk
fix a typo in Documentation/pi-futex.txt
BUG_ON conversion for fs/xfs/
BUG_ON() conversion in fs/nfsd/
BUG_ON conversion for fs/reiserfs
BUG_ON cleanups in arch/i386
BUG_ON cleanup in drivers/net/tokenring/
BUG_ON cleanup for drivers/md/
kerneldoc-typo in led-class.c
debugfs: spelling fix
rcutorture: Fix incorrect description of default for nreaders parameter
parport: Remove space in function calls
Michal Wronski: update contact info
Spelling fix: "control" instead of "cotrol"
reboot parameter in Documentation/kernel-parameters.txt
Fix copy&waste bug in comment in scripts/kernel-doc
remove duplicate "until" from kernel/workqueue.c
ite_gpio fix tabbage
fix file specification in comments
...
Fixed trivial path conflicts due to removed files:
arch/mips/dec/boot/decstation.c, drivers/char/ite_gpio.c
Adding support for Nova-T-PCI PCI ID 0070:9000
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove defines of FALSE/TRUE because they are not used.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed norm_notchfilter function. All the code is bound to 4 x FSC, so, any
other filter won't work fine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the setting of the cx2388x notch filter to match that of
the video capture sample frequency, removing some annoying interference
lines THAT would appear when capturing composite video. This has been tested
in PAL and NTSC TV norms.
It sets the Y/C separation luma notch filter, which removes the chroma signal
from the luma signal when using a composite input.
The luma notch filter operates at the video decoder's frequency, not the ADC's
frequency or at the frequency of the scaled video. Y/C separation happens after
the sample rate converter, before video scaling.
The datasheet provides plots of the filter response for three _video decoder_
frequencies, 4x Fsc, square pixel, and ccir601. These are the same three
frequencies for the notch filter control. It seems pretty clear that this
filter should be set based on the video decoder frequency. The cx88 driver
always uses a video decoder frequency of 4xFsc.
Signed-off-by: Lars Gjesse Kjellberg <lars.g.kjellberg@get2net.dk>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fix for intermittent oops's during boot which occurs
in cx88_call_i2c_clients when dvb_attach is bringing up
the frontend.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use NULL instead of 0 for pointer value, eliminate sparse warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Club3D Zap TV2100 has been reported to be a clone of the Yuan PG300 and
KWorld/VStream XPert DVB-T with cx22702
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The flags for mpeg capabilities are sub-optimally named as
CX88_BOARD_DVB and CX88_BOARD_BLACKBIRD, which creates some confusion.
This patch renames the above to CX88_MPEG_DVB and CX88_MPEG_BLACKBIRD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some basic cleanup in preperation for a future patch where
the cx88-mpeg functions have to deal with the port being
used by multiple frontends in (mpeg2 hw encoder and dvb demod).
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A generic change to cards to allow any board to specify whether
it needs the wm8775 module loaded (by the core) or not.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (180 commits)
V4L/DVB (4641): Trivial: use lowercase letters in hex subsystem ids
V4L/DVB (4639): Cx88: add autodetection for alternate revision of Leadtek PVR
V4L/DVB (4638): Basic DVB-T and analog TV support for the HVR1300.
V4L/DVB (4637): Add a default method for VIDIOC_G_PARM
V4L/DVB (4635): Extend bttv and saa7134 to check for both AGP and PCI PCI failure case
V4L/DVB (4634): Zr36120: implement pcipci checks
V4L/DVB (4632): Zoran: Implement pcipci failure check
V4L/DVB (4631): Av7110: remove V4L2_CAP_VBI_CAPTURE flag
V4L/DVB (4630): Av7110: FW_LOADER depemdency fixed
V4L/DVB (4629): Saa7134: add card support for Proteus Pro 2309
V4L/DVB (4628): Fix VIDIOC_ENUMSTD ioctl in videodev.c
V4L/DVB (4627): Vivi crashes with mplayer
V4L/DVB (4626): On saa7111/7113, LUMA_CTRL need a different value
V4L/DVB (4624): Tvaudio: Replaced kernel_thread() with kthread_run()
V4L/DVB (4622): Copy-paste bug in videodev.c
V4L/DVB (4620): Fix AGC configuration for MOD3000P-based boards
V4L/DVB (4619): Fixes some I2C dependencies on V4L devices
V4L/DVB (4617): Problem with dibusb-mb.c USB IDs
V4L/DVB (4616): [PATCH] Nebula DigiTV USB RC support
V4L/DVB (4614): Export symbol saa7134_tvaudio_setmute from saa7134 for saa7134-alsa
...
i2c-algo-bit: Discard the mdelay data struct member
The i2c_algo_bit_data structure has an mdelay member, which is not
used by the algorithm code (the code has always been ifdef'd out.)
Let's discard it to save some code and memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add autodetection for PCI subsystem ID 107d:6632, to detect as
a Leadtek PVR 2000
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the first in a series of patches to add full WinTV-HVR1300
support to Linux. This first patch will enable analog TV support
and DVB-T support. Later patches will add the hardware MPEG encoder
support.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Software I2C were using a very conservative value of udelay=16, meaning about
20Kbps. According with Philips I2C datasheet, the i2c should answer well for
times at the order of 4.7 us. So, using udelay=5 should work for all devices.
After this patch, the speed should be close to 66,67 Kbps, with the current
kernel software bitbang, with 30/60 duty cycle.
Anyway, added a new parameter (i2c_udelay) that would allow using conservative
values, if eventually a hardware doesn't support the datasheet values.
Thanks to Jean Delvare <khali@linux-fr.org> for pointing this improvement.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several changes at register stuff were done since commit
b45009b028, but I've forgot
to add the copyright line for this. Those changes allowed
cx88 to have multiple tuners, allowing it to support hardware with
separated radio and video tuners. It also allows binding a tuner to an
specific i2c address.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: David Bussenschutt <buzz@oska.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: Eric Thomas <ethomas@claranet.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A patch from Aug, 17 activated by mistake OVERLAY flag on cx88-video,
together with several cx88-blackbird cleanups. This makes the cx88 driver
to report:
/dev/video0 [v4l2]: ioctl VIDIOC_G_FBUF: Invalid argument
instead of:
/dev/video0 [v4l2]: no overlay support
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix keycode calculations (all codes for this remote were wrong due to a
lost + sign)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch implements the newer v4l2 control features to make the
standard user controls and mpeg encoder controls of cx88-blackbird
video encoder boards available to userspace.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
implemented VIDIOC_LOG_STATUS in the cx88-blackbird driver
to show the status of i2c clients and the cx23416 mpeg encoder.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch creates a new Kconfig menu option, entitled,
"Blackbird MPEG encoder support (cx2388x + cx23416)"
so that the cx88-blackbird mpeg encoder module can be
chosen separately.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed the switch..case block in blackbird_probe for setting encoder height
based on video standard. All blackbird devices can rely on tvnorm->id to
retrieve this information from the cx2388x video decoder - tuner_formats
should not be used to determine the encoding video standard.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CX2341X port was always set to 'memory', but 'streaming' is also possible
ivtv uses the memory (DMA) interface with the CX2341X, while pvrusb2 and
cx88-blackbird use the streaming interface. This setting is now selectable
by the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Put old MPEGCOMP API under #if __KERNEL__ and issue warnings when used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the cx2341x.c module that handles the programming of the Conexant
cx23415/6 MPEG encoder chip used by cx88-blackbird, pvrusb2 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
clear EN_I2SIN_ENABLE bit for ASUS PVR-416 to enable audio
streaming in both raw video and blackbird mpeg encoder modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for FusionHDTV 3 Gold (original revision), using the
card definition for FusionHDTV3 Gold-Q
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There's a call at cx88-tvaudio to reset DMA sound on channel change; that
call was killing cx88-alsa whenever the channel was changed, resulting
in no sound. Remove those calls if cx88-alsa is selected to be compiled.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa was resetting the card on load, causing the IRQ IR handler
to go away (maybe others, too). There's no actual need to reset the
card, though, so that line was removed
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was an unmasked bit in the keycodes that was causing random
behaviour (the code could be N or N+1). Masked that bit now.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch splits up dvb_pll_attach and isl6421_attach function calls
such that the lines do not exceed 80 columns. This patch is purely cosmetic,
with no functional change at all.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- moved CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL frontend_attach code up
to share the #ifdef block with CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PLUS
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The description of the card has been updated to it's full name/model.
The tuner has also been switched to a more compatible one (radio
wasn't working, now it is)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Videodev now is capable of better handling V4L2 api, by
processing V4L2 ioctls and using callbacks to the driver.
The drivers should be migrated to the newer way and the older
one will be obsoleted soon.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds support for the Y0400052 remote supplied with this card.
In addition to adding a number of buttons to the current winfast definition,
it enables all the keys currently masked out with #ifdef 0.
It is supplied separately as it remaps two keys from the current definition,
The teletext button now sends KEY_TEXT instead of KEY_SUBTITLE, as that
keycode is used by the subtitle button.
KEY_BACK was changed to KEY_LAST to group it with KEY_NEXT.
Other then that the keys don't overlap, so this should support several
different versions of the Leadtek remotes.
Signed-off-by: Malcolm Valentine <farkit@iinet.net.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add DVB-T and PAL-G television support for Winfast DTV2000H
Signed-off-by: Malcolm Valentine <farkit@iinet.net.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enabled s-video and composite video inputs.
- Updated comments to reflect the current support for this card.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for a new cx88 card, including it's remote
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for ProLink Pixelview Playtv@P7000
Raw video and MPEG encoded video confirmed to work properly.
SVideo, Composite and FM inputs are untested - disabled for now.
Signed-off-by: Angelo Marconi <am@massalombarda.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework diseqc support to be more in line with the other demod drivers.
Fix Nova-S-Plus/Nova-SE2 diseqc.
Cleanup API.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho