* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
V4L/DVB: sms: Convert IR support to use the Remote Controller core
V4L/DVB: sms: properly initialize IR phys and IR name
V4L/DVB: standardize names at rc-dib0700 tables
V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
V4L/DVB: dib0700: properly implement IR change_protocol
V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
V4L/DVB: dib0700: avoid bad repeat
V4L/DVB: Port dib0700 to rc-core
V4L/DVB: Add a keymap file with dib0700 table
V4L/DVB: dvb-usb: add support for rc-core mode
V4L/DVB: dvb-usb: prepare drivers for using rc-core
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
V4L/DVB: rj54n1cb0c: fix a comment in the driver
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
V4L/DVB: mediabus: fix ambiguous pixel code names
...
RJ54N1CB0C is a Sharp camera sensor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first VC0321 settings were done at webcam connection only. They must also
be done on resume after suspend.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.
Tested-by: Kyle Baker <kyleabaker@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When there is an audio device, use a lower alternate setting.
This patch does not fix correctly all audio and bandwidth problems.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function has sanity checks to make sure that "dev" is non-null. I
moved the dereference down below the checks. In the current code "dev"
is never actually null.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found that in ivtvfb_callback_cleanup and ivtvfb_callback_init
there are unneeded tests for itv being NULL. But itv is initialized
as container_of with non-zero offset in those functions, so it is
never NULL (even if v4l2_dev is). This was found because itv is
dereferenced earlier than the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes possible race conditions in queue management with SMP:
when a frame was completed, the irq function tried to use the next frame
buffer. At this time, it was possible that the application on an other
processor updated the frame pointer, making the image to point to a bad
buffer.
The patch contains two main changes:
- the image transfer uses the queue indexes which are protected against
simultaneous memory access,
- the image pointer which is used for image concatenation is only set at
interrupt level.
Some subdrivers which used the image pointer have been updated.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem may occur with SMP:
- a frame is completed at interrupt level (in gspca_frame_add with
packet_type == LAST_PACKET,
- just after clearing the bit V4L2_BUF_FLAG_QUEUED and before setting
the bit V4L2_BUF_FLAG_DONE, on the other processor, the application
tries to requeue the same frame buffer,
- then, the qbuf function succeeds because ALL_FLAGS are not set.
The fix sets and resets the two flags in one instruction.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit b402843787
the 'driver_data' field resides in device's struct device_private
which may be allocated by dev_set_drvdata() if device_private
struct was not allocated previously.
dev_set_drvdata() is used in video_set_drvdata() to set
the driver's private data pointer in v4l2 drivers. Setting
the private data _before_ registering the v4l2 device results
in a memory leak since __video_register_device() also calls
video_set_drvdata(), but after zeroing the device structure.
Thus, the reference to the previously allocated device_private
struct goes lost and a new device_private will be allocated.
All v4l drivers which call video_set_drvdata() _before_
calling video_register_device() are affected. The patch fixes
__video_register_device() to preserve previously allocated
device_private reference.
Caught by kmemleak.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for Video-In (VIU) unit of Freescale
MPC5121e. The driver supports RGB888/RGB565 formats,
capture and overlay on MPC5121e DIU frame buffer.
Signed-off-by: Hongjun Chen <hong-jun.chen@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_MINMAX quirk. Add a corresponding entry
in the device IDs list
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Data buffers on the stack are not allowed for USB I/O. Use dynamically
allocated buffers instead when querying control length and control
capabilities.
The control capabilities are now also stored in the uvc_control
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the macros instead of hardcoding numerical constants for the
controls information bitfield.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVCIOC_CTRL_MAP ioctl doesn't support menu entries for menu
controls. As the uvc_xu_control_mapping structure has no reserved
fields, this can't be fixed while keeping ABI compatibility.
Modify the UVCIOC_CTRL_MAP ioctl to add menu entries support, and define
UVCIOC_CTRL_MAP_OLD that supports the old ABI without any ability to add
menu controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the v4l2 spec, writing any value to a button control should
result in the action belonging to the button control being triggered.
UVC cams however want to see a 1 written, this patch fixes this by
overriding whatever value user space passed in with -1 (0xffffffff) when
the control is a button control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It might be useful to be able to disable the IR support, either for
debugging purposes, or just for users who know they won't use the IR
remote control anyway. On many cards, IR support requires expensive
polling/sampling which is better avoided if never needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This is the same as was done for
the bttv driver several months ago. Might solve bugs which have not yet
been reported for some cards. It makes both drivers consistent, and
makes it easier to disable IR support (coming soon.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the cx23885 driver to use the new in kernel IR pulse
decoders for the integrated CX2388[578] IR controllers. Rip out a lot
of RC-5 decoding related code in the process and rename some variables
for clarity or to more accurately describe their usage.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move from the generic, shared card_ir state structure to a cx23885 driver
specific IR state structure in anticipation of moving to the new IR pulse
decoders in the IR core.
Fix up the card name truncation in the dmesg log while we're at it,
by avoiding using fixed length string storage in our new IR state
structure.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image pointer and its length are now in the main structure instead
of in the frame buffer. They are updated on application vidioc_qbuf and
in the URB interrupt function when ending an image.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Kconfig variables are moved to video/davinci/Kconfig through another
patch and these are to be therefore removed
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently VPFE Capture driver and DM6446 CCDC driver is being
reused for AM3517. So this patch is preparing the Kconfig/makefile
for re-use of such IP's.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the hdpvr_probe () function, when an error occurs while probing the device,
the workqueue created by the create_single_thread () call is not properly
destroyed.
Signed-off-by: Perceval Anichini <perceval@trilogic.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s2255drv: cleanup of device structure
cleanup of device structure.
single channel array instead of multiple arrays in device for
each channel property.
simplifies open callback by removing search for channel index.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is just a cleanup patch. We never use the "udev" variable so I
have removed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 05/29/10 01:30, Jean-Francois Moine wrote:
> On Fri, 28 May 2010 13:03:28 -0400
> Amerigo Wang<amwang@redhat.com> wrote:
>
>> Subject: [PATCH 6/6] Remove obsolete zc0301 v4l driver
>>
>> Duplicate functionality with the gspca_zc3xx driver, zc0301 only
>> supports 2 USB-ID's (because it only supports a limited set of
>> sensors) wich are also supported by the gspca_zc3xx driver
>> (which supports 53 USB-ID's in total).
>
> You forgot to remove the conditionnal compilation in the gspca_zc3xx
> driver (USB_DEVICE(0x046d, 0x08ae) in gspca/zc3xx.c)
>
Right, thanks for pointing this out!
Attached is the updated patch, please use this one instead.
Thanks!
Duplicate functionality with the gspca_zc3xx driver, zc0301 only
supports 2 USB-ID's (because it only supports a limited set of
sensors) wich are also supported by the gspca_zc3xx driver
(which supports 53 USB-ID's in total).
Signed-off-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_dmabuf and videobuf_vmalloc_memory fields have a vmalloc
field to store the kernel virtual address of vmalloc'ed buffers. Rename
the field to vaddr.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fields are assigned but never used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those functions are only called inside videobuf-dma-sg.c, make them
static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88 and cx25821 drivers abuse videobuf_buffer to handle audio data.
Remove the abuse by creating private audio buffer structures with a
videobuf_dmabuf field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating dirty wrappers around videobuf_dma_map/unmap that
create a dummy videobuf_queue structure, modify videobuf_dma_map/unmap
to take a device pointer argument and use it directly. The
videobuf_sg_dma_map/unmap then become unused and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is not specific to mmap, hence the rename.
Add a check whether we are not streaming or reading (for read mode that
uses the stream queue) before freeing anything.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These functions allocate videobuf_buffer structures only. Renaming in order
to prevent confusion with functions allocating actual video buffer memory.
Rename the functions in videobuf-core.h videobuf-dma-sg.c as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a mutex_unlock missing on the error path. In the other functions in
the same file the locks and unlocks of this mutex appear to be balanced,
so it would seem that the same should hold in this case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* mutex_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* mutex_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My previous patch to depend on FONTS was not sufficient since
FONTS is boolean. VIDEO_VIVI needs to depend on a tristate so that
it won't be enabled as =y when framebuffer is built as modular, so
modify it to depend on the same symbols that FONTS depends on, which
are FRAMEBUFFER_CONSOLE || STI_CONSOLE.
Fixes this build error when VIDEO_VIVI=y and FRAMEBUFFER_CONSOLE=m:
vivi.c:(.init.text+0x7205): undefined reference to `find_font'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Partially convert drivers/media/video/ir-kbd-i2c.c to
not use ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Partially convert drivers/media/video/cx88/cx88-input.c to not use
ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of generating one printk for every IR read, prints it only when
count is different from the last count.
While here, as this code is called on every 100ms during the runtime
lifetime, do some performance optimization, assuming that, under normal
circumstances, it is unlikely that the driver would get a new key/key
repeat on every poll.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers/media/video/em28xx/em28xx-input.c to not use ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Genius iSlim 310 webcam to the supported list of the PAC7302 driver.
For more information see http://linuxtv.org/wiki/index.php/PixArt_PAC7301/PAC7302 .
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Extra spaces to align some variable names and a defined value
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Change of rounded image resolutions to the real ones for MI2020 sensor
in order to discard 2 random lines in the bottom of images
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Setting changes applied after an end of image marker reception
This is the way MI2020 sensor works.
It seems to be logical to wait for a complete image before
to change a setting.
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- 1 ms "msleep" applied to each sensor after USB control data exchange
This was done for two sensors because these exchanges were known to
be too quick depending on laptop model.
It is fairly logical to apply this delay to each sensor
in order to prevent from having errors with untested hardwares.
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new MI2020 driver version made from a webcam gift
- all previous flavors of this driver removed
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch address an arithmetic error for the case where the only remaining
content in the USB packet was the "225Axxxx" start of active video. In cases
where that happened to be at the end of the frame, we would inject it into the
videobuf (which is incorrect). This caused fields to be intermittently
rendered off by two pixels.
Thanks to Eugeniy Meshcheryakov for bringing this issue to my attention
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add NTSC closed captioning support for au0828 based products. Note that this
also required reworking the locking to support streaming on both the video and
VBI devices (the logic for which I copied from my changes made to the em28xx
several months ago).
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the firmware has failed, this patch will automatically reload &
restart the card. The previous card state will be restored on a
successful restart. Firmware reload will only happen if neither the
encoder or decoder is active. If the card is busy then behaviour is as
before, returning -EIO on device access until the reload can occur. On
cards that support video output, coloured bars will be displayed during
the reload.
Andy Walls (ivtv maintainer and patch committer) made minor tweaks to
comments and the logged messages, but nothing substantial otherwise.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From Ian's e-mail:
When a device is opened the firmware state will be checked. If it isn't
responding then the open will fail with -EIO. Due to the nature of the
hardware, a single failed check will block everything since we don't know
exactly what has failed. A side effect of this is the blocking of debug
access, so an additional debug level has been created which allows the block
to be bypassed.
Andy Walls' modifications:
I modified Ian's patch to add a separate fw_debug module parameter to change
the driver's behavior, as opposed to using the normal debug module parameter.
The fw_debug module parameter is only available when CONFIG_VIDEO_ADV_DEBUG
is set.
I also made some minor whitespace adjustments and changed some warning
messages to be a bit more specific. s/happy/glad/g
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is used when the USB video interface is checked by
the subdriver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- variable / function rename
- set the gains in one exchange
- don't alter the register 80 which contains the AWB flag
and other sensor specific values
- the global gain is now the average of the R, G and B gains.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also renames the last polling message from the closer one
of the ms-windows driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new table is sorted and extracted from a clear part of the MS-Windows
driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also changes a bit the contrast control.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These registers seem to act on the JPEG compression whose control
is not implemented in the current driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is now included in the subdriver structure instead
of being allocated and freed at capture start and stop.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
setcolors(0 is a no-op for 7670 sensors, so we should not report a
saturation control for 7670 sensors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
What we've called brightness so far actually is an exposure control,
rename it and fixup the maximum and default values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a problem with certain tv8532 cams, where sometimes there
hsync/vsync locks one pixel of where it normally locks. While trying to
fix this (which I failed to do). I noticed there are lots if duplicate
register writes and unnecessary register reads in the tv8532 driver. This
patch cleanes these ups (which has no negative effects, but unfortunately
also does not help).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the ovfx2 bridge sometimes the first few frames in a stream
would be no good, as the bridge and sensor are not in complete hsync /
vsync yet. This can easily be detected by checking the framesize. So if the
framesize is short and it is one of the 1ste 3 frames after an sd_start,
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With enabled debugging sh_mobile_ceu_camera.c dereferences an invalid or a NULL
pointer. Thanks to James Wang for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These function are needed to use camera.
This patch was tested with sh_mobile_ceu_camera
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
Carvalho de Assis modified the original driver to get it working on more recent
kernels. I modified it further to add support for i.MX25. This driver has been
tested on i.MX25 and i.MX27 based platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a partial revert of 421f91d21a
("fix typos concerning "initiali[zs]e"") for ov511 driver, as it is
going to be completely removed in the next release anyway.
Fixes conflict in linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Calling g_fmt before s_fmt resulted in a NULL pointer dereference as no
default formats were being selected on probe.
Reported-by: Németh Márton <nm127@freemail.hu>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Issuing a GET_MIN request on the power line frequency control times out
on at least the Apple iSight. As the UVC specification doesn't list
GET_MIN/MAX/RES as supported on that control, remove them from the
uvc_ctrls array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a short delay when stopping the decoder, allowing it to settle and
preventing some unexpected interaction with other firmware commands.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge EEPROM tuner code 168 has recently shown up on HVR-1600 TV
capture cards supported by the cx18 driver. This change allows analog
tuner type autodetection to succeed for these cards.
Information for decoding tuner code 168 was provided by Hauppauge.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Actually OMAP doesn't support scatter-gather DMA for
Display subsystem but due to legacy coding it has been overlooked
till now.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes -
- Kconfig option dependancy changed to ARCH_OMAP2/3 from
ARCH_OMAP24XX/34XX
- There are some moments of function from omap_dss_device
to omap_dss_driver. Incorporated changes for the same.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Upcoming workqueue updates will no longer guarantee fixed workqueue to
worker kthread association, so giving RT priority to the irq worker
won't work. Use kthread_worker which guarantees specific kthread
association instead. This also makes setting the priority cleaner.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: ivtv-devel@ivtvdriver.org
Cc: linux-media@vger.kernel.org
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added small delay on device open & close to allow hardware to settle. Move yuv
register restore to before the decoder firmware call to stop playback.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For yuv video output, pass fake values to avoid firmware trying to change
video standard.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check firmware state when loading module & if firmware is not responding exit
with an error. When module is unloaded, only disable the framebuffer & not all
decoder output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[Andy Walls comment:] This patch from Ian removes the cx2341x module lying
about the setting of the temporal filter for the log status ioctl().
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A trivial change to update my email address from my dead awalls@radix.net
address to my current awalls@md.metrocast.net address.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In each case, the print involves dereferencing a value that is NULL or is
near NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem is that dprintk() dereferences "dev" which is null here.
The i2cdprintk() uses "ir" so that's OK.
Also Jean Delvare pointed out a typo in the comment so we may as well
fix that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code had two break statements in a row.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The "dev" variable is used as a list cursor in a list_for_each_entry()
loop and can never be null here so I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add slab.h to fix ak881x build:
drivers/media/video/ak881x.c:265:error: implicit declaration of function 'kzalloc'
drivers/media/video/ak881x.c:265:warning: assignment makes pointer from integer without a cast
drivers/media/video/ak881x.c:283:error: implicit declaration of function 'kfree'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IR support on FusionHDTV cards is broken since kernel 2.6.31. One side
effect of the switch to the standard binding model for IR I2C devices
was to let i2c-core do the probing instead of the ir-kbd-i2c driver.
There is a slight difference between the two probe methods: i2c-core
uses 0-byte writes, while the ir-kbd-i2c was using 0-byte reads. As
some IR I2C devices only support reads, the new probe method fails to
detect them.
For now, revert to letting the driver do the probe, using 0-byte
reads. In the future, i2c-core will be extended to let callers of
i2c_new_probed_device() provide a custom probing function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: "Timothy D. Lenz" <tlenz@vorgon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for one more remote control type for Avermedia
M135A (model RM-K6), shipped with Positivo machines.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for Avermedia M733A. The original version for
linux 2.6.31 was sent to me from Avermedia, original author is unknown.
I ported it to current kernels, expanded and fixed key code handling for
RM-K6 remote control, and added an additional pci id also supported.
[mchehab@redhat.com: make checkpatch.pl happier]
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since there is only one possible format just have all three calls
do the same.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of unnecessary code since this driver supports only one
pixel format. Removing this code will make the transition to the
mbus API easier as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several calls (try_fmt, g_parm among others) changed the current standard
as a side effect of that call. But the standard may only be changed by s_std.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
enum_mbus_fmt received an index argument that was defined as an int instead
of an unsigned int. This is now fixed. This had the knock-on effect that the
index argument in the callback get_formats in soc_camera.h also had to be
changed to unsigned int.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that this driver is only used by em28xx and that em28xx does not
actually call the enum/try/s_fmt ops of mt9v011. So these functions
have never been tested.
And in fact the driver really implements cropping instead of scaling. So it
seems to be doing the wrong thing :-(
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18 has now switched over completely to the new mediabus subdev ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Delete sysfs class device as the _very_ last step, after
we're sure that all driver contexts have gone away first. This is
important because it appears that there isn't any protection from a
struct device instance reference a deleted struct class instance. The
assumption in the kernel code appears to be that the class instance is
assumed to be around for the life of the device. So we can't let the
class instance go away until all referencing device instances are
gone; this is ensured by delaying removal of the class instance until
after the driver contexts have all gone away. This bug has been
present for a very long time but it didn't apparently become malignant
until recently (probably because of other changes in the kernel).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Need one extra attribute slot allocated so that worst case still has a
trailing null pointer. This wasn't causing visible symptoms; it was
found through inspection while investigating other issues.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Correctly reference count pointer to parent USB device when linked
from sysfs interface. This is technically a pretty nasty problem,
however as far as I know nobody had been getting burned by it (yet).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Fix oops caused by touching deleted memory after
unregistration. This bug was introduced when we had started using
video_device_node_name() - that function was being called potentially
after the underlying structure (referenced by that function) had been
deleted. The fix rearranges things slightly so that the function is
called before destruction takes place.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a flag in the device attribute structure which can be used
to mark support for a particular device as experimental. Any devices
flagged in this way, when encountered at run-time, will generate a
warning message to the kernel log.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Fix RF tuner problem with gotview hardware - this bug was
introduced when switching over to the subdev model of driver control
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix kernel Oops when number of NetUP Dual DVB-S2-CI cards more than
DVB_MAX_ADAPTERS limit.
[mchehab@redhat.com: move the return to the proper place]
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: due to lack of hardware this conversion is untested.
However, it is pretty straightforward so I do not expect any problems.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: due to lack of hardware I was not able to test this conversion.
But it is pretty straightforward, so I do not expect any problems.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch (as1373) fixes a couple of drivers outside the USB
subtree. Devices are now disabled or enabled for autosuspend by
calling a core function instead of setting a flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix vivi and mem2mem_testdev build errors: need to #include <linux/slab.h>:
drivers/media/video/vivi.c:1144: error: implicit declaration of function 'kfree'
drivers/media/video/vivi.c:1156: error: implicit declaration of function 'kzalloc'
drivers/media/video/vivi.c:1156: warning: assignment makes pointer from integer without a cast
drivers/media/video/mem2mem_testdev.c:862: error: implicit declaration of function 'kzalloc'
drivers/media/video/mem2mem_testdev.c:862: warning: assignment makes pointer from integer without a cast
drivers/media/video/mem2mem_testdev.c:874: error: implicit declaration of function 'kfree'
drivers/media/video/mem2mem_testdev.c:944: warning: assignment makes pointer from integer without a cast
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My concern initially was we dereference "dev" in the parameter list to
s2255_dev_err() but it turns out that code path is never used.
The s2255_stop_readpipe() is only called from one place and "dev" is
never null. So this patch just removes the whole condition here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: linux-dev@sensoray.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code didn't handle the case where vdev was not found so I
added a check for that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: linux-dev@sensoray.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We dereference "ov" unconditionally throughout the function so there is
no way it can be NULL here. This code has been around for ages so if
it were possible for "ov" to be NULL someone would have complained.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reverse HAS_BUTTON logic since most webcams either have a button or if
they don't don't bother to send any interrupts. However I have at least
one model that appears to leave the button GPIO floating and can send
a bogus interrupt.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PRIORITY is also part of the ioctls that need to check the
access priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The detection of the saa711x often failed. Adding a small delay before
attempting to detect it fixed this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_register already sets intfdata, no need to do this again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disconnecting the HDPVR caused a kernel oops if lockdep was enabled.
In addition, if an app still had video0 open and attempted to call ioctl
when the device was already disconnected the system would crash.
Move the freeing and cleanup code to the release function: that is the
right place for it since you know when you get there that nobody is
using the device.
Also removed usb_set_intfdata: v4l2_device_register sets this already
to v4l2_dev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to lock when unregistering the device: clear_bit is already an
atomic operation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'type' field was undefined but should be set to ANALOG_TV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no signal or valid format is detected, then VIDIOC_QUERY_DV_PRESET must
return 0 and set the preset to V4L2_DV_INVALID.
This driver returned an error instead.
Also simplified the kernel messages a bit: change v4l2_err to v4l2_dbg (not
detecting a signal/valid format is not an error, so only print this info when
debug == 1) and do not call v4l_fill_dv_preset_info: it's overkill to do this
just for a debug message.
Thanks to Mats Randgaard for bringing this to my attention.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that s_fmt is no longer used for VBI format setup in subdevs, remove
the VBI support from s_fmt.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
This should have been removed in ivtv, but it was just copied-and-pasted
into cx18.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
Switching between raw and sliced VBI changed in 2.6.28 and this memset
should have been removed at that time. It was never noticed because
the bridge driver will fill in the fmt.vbi values anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control step values reported by the device are used as a divisor
unchecked, which can result in a division by zero.
Check the step value and make it 1 when null.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC relative controls (exposure time, iris, focus, zoom, pan/tilt)
are write-only (despite the UVC specification stating that the GET_CUR
request is mandatory). Mark the controls as such, and report the related
V4L2 controls V4L2_CTRL_FLAG_WRITE_ONLY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Miricle 307K (17dc:0202) camera reports a 16-bit greyscale format,
support it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vivi uses find_font(), which is only available when FONTS
is enabled, so make vivi depend on FONTS.
ERROR: "find_font" [drivers/media/video/vivi.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the V4L2 specification, poll() should set POLLOUT | POLLWRNORM
flags for output devices after the frame has been displayed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_pages_to_sg() and videobuf_vmalloc_to_sg() happen to create
a scatterlist element for every page. However, this is not true for
bus addresses, so other functions shouldn't rely on the length of the
scatter list being equal to nr_pages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf-core checks if .sync ops is defined before calling.
So, we don't need a do-nothing function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While analyzing one of the videobuf patches, I noticed that
videobuf_dma_sync is only used internally inside videobuf-dma-sg.
So, let's remove this function, merging the code at __videobuf_dma_sync()
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For recoverable stream errors dqbuf() now returns 0 and the error flag
is set instead of returning EIO.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I have 3 IVC-200 cards (with 4 video channels on each).
2 of the cards identify theirselves as 000[0-3]:a155 (ids already in
cardlist) and another one identifies itself as 080[0-3]:a155, which ids
were unknown so far.
Note - it's IVC-200, not IVC-200G.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch retrieve the correct mac address from the eeprom for TeVii
S470 card.
Signed-off-by: Pierre Gronlier <pierre.gronlier@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Serialize DVB initialization, to avoid it to happen while analog
initialization is still happening.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx88-mpeg.c, there is code that sets core->input to CX88_VMUX_DVB.
However, this may be incorrect, since core->input is actually an
index to core->board.input[], which has not enough elements to be
indexed by the value of CX88_VMUX_DVB. So, the modified code searches
core->board.input[] for an input with a type of CX88_VMUX_DVB, and if
it does not find one, the index is simply set to zero.
The change may not have much effect, though, since it appears the only
case when core->input is actually used is when the current input is
being queried.
Signed-off-by: Istvan Varga <istvanv@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers/media/video/cx231xx/cx231xx-input.c to not
rely on ir-functions.c.
(I do not have the hardware so I can only compile test this)
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pulse-distance is not a protocol, it is a line coding (used by some protocols,
like NEC). Looking at the uses of IR_TYPE_PD, the real protocol seems to be
NEC in all cases (drivers/media/video/cx88/cx88-input.c is the only user).
So, remove IR_TYPE_PD while it is still easy to do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
spin_is_locked() always returns zero when spinlock debugging is
disabled on a single CPU machine. Replace WARN_ON() with
assert_spin_locked().
Thanks to Laurent Pinchart for spotting this!
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brightness is done by the gamma tables and not by single bridge registers.
It will be back as soon as an algorithm will be found.
This change also fixes the autogain problem found by Jose Alberto Reguero
(webcam 046d:08dd).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error was introduced by "gspca - zc3xx: Rename the USB sequences."
in commit e945e2e44c798f84494260c02478d3c23965bb93.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams 0c45:613e may contain the sensors ov7630 or soi768.
A sensor probe is done at init time when the sensor is declared ov7630.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the V4L2 specification, applications set bytesused, field and
timestamp fields of struct v4l2_buffer when the buffer is intended for
output and memory type is MMAP. This adds proper copying of those values
to videobuf_buffer so drivers can use them.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
