Clean up a few different parts of omap_set_pwrdm_state():
- Remove a superfluous call to pwrdm_state_switch(). Not needed
unless LOWPOWERSTATECHANGE is used, because the state switch code is
called by either clkdm_sleep() or clkdm_allow_idle().
- Add code to wait for the power state transition in the OMAP4+ low
power state change. This is speculative, so I would particularly
appreciate feedback on this part.
- Remove a superfluous call to pwrdm_read_pwrst().
- Update variable names to be more meaningful (hopefully) and precise.
- Fix an error path bug that would not place the clockdomain back into
hardware-supervised idle or sleep mode if the power state could not
be programmed.
The documentation for this function still needs major improvements;
that's left for a later patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove some superfluous calls to pwrdm_clear_all_prev_pwrst().
pwrdm_pre_transition(), which appears a few lines after these calls,
invokes pwrdm_clear_all_prev_pwrst() on each powerdomain -- there's no
need to do it twice.
N.B.: some of us have observed that accesses to the previous
powerstate registers seem to be quite slow. Although the writes
removed by this patch should be buffered by the write buffer, there is
a read to a PRM register immediately afterwards. That will block the
OMAP3 MPU until all of those writes complete. So this patch should
result in a minor performance improvement during idle entry.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
[khilman@ti.com: removed a couple more for OMAP4]
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With the introduction of iomap changes platform init code
fails for emu.c if CONFIG_OMAP3_EMU is selected:
arch/arm/mach-omap2/emu.c:35:8: error:
'L4_EMU_34XX_BASE' undeclared here (not in a function)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Building omap_devices should only be done at init time, and since
omap_device_build() is using early_platform calls which are also
__init, this ensures that omap_device isn't trying to use functions
that disappear.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that omap hsmmc init is split into two functions, it's safe
to mark omap_hsmmc_init and omap_mux related functions to __init.
This basically reverts the following fixes for the case where
TWL was compiled as a module:
a98f77b (ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup())
8930b4e (ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c)
Additionally it fixes up the remaining section warnings for
all callers of omap_mux functions.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers should no longer use omap_read/write functions
but instead use ioremap + read/write functions.
As some USB legacy code is still shared between omap1 and
omap2420, let's limit the omap_read/write to plat/usb.h.
Note that the long term fix is to update the drivers to
use ioremap and read/write functions. That can now be
done as a separate patch series that is limited to the
USB drivers.
Also make sure the legacy omap1-keypad.c driver builds
if selected for 2420 based systems.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove omap_{read,write}l() from the 24xx PM code. The clocksource
code should now handle what this was supposed to do.
Tested on N800 -- but it's hard to say whether this fixes anything.
OMAP24xx static suspend path is currently broken, and this patch
doesn't change that.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flag single_channel in struct omap2_mcspi_device_config is not used
by drivers/spi/spi-omap2-mcspi.c so we may remove it from include/plat/mcspi.h
and affected board files.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
With the removal of disable_fiq on rpc and addition MULTI_IRQ_HANDLER,
entry-macro.S is no longer needed for platforms that select
MULTI_IRQ_HANDLER and the include of it can be conditional.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Only rpc uses disable_fiq macro. Change it to a run-time installed
default FIQ handler. The handler is installed before FIQ is enabled
so the behavior should be unchanged.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Only 3 platforms need arch_ret_to_user macro, so add ARCH_HAS_RET_TO_USER
kconfig option and make iop13xx, iop32x and iop33x select it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Expose omap_device_{alloc, delete, register} so we can use them outside
of omap_device.c.
This approach allows users, which need to manipulate an archdata member
of a device before it is registered, to do so. This is also useful
for users who have their devices created very early so they can be used
at ->reserve() time to reserve CMA memory.
The immediate use case for this is to set the private iommu archdata
member, which binds a device to its associated iommu controller.
This way, generic code will be able to attach omap devices to their
iommus, without calling any omap-specific API.
With this in hand, we can further clean the existing mainline OMAP iommu
driver and its mainline users, and focus on generic IOMMU approaches
for future users (rpmsg/remoteproc and the upcoming generic DMA API).
This patch is still considered an interim solution until DT fully materializes
for omap; at that point, this functionality will be removed as DT will
take care of creating the devices and configuring them correctly.
Tested on OMAP4 with a generic rpmsg/remoteproc that doesn't use any
omap-specific IOMMU API anymore.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we get the following error:
arch/arm/mach-omap2/built-in.o: In function `n8x0_mmc_callback':
twl-common.c:(.text+0x108a0): undefined reference to
`omap_mmc_notify_cover_event'
Fix this by warning about unusable MMC cover events.
The long term fix needs to change the MMC drivers to
register board specific callbacks directly with PMIC.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On some omaps twl4030_gpio has a callback to try to initialize
the MMC controller. If twl4030_gpio is compiled as a module,
bad things can happen because the callback function starts
calling functions that are supposed to be marked __init:
Kernel panic - not syncing: Attempted to kill the idle task!
twl4030_gpio twl4030_gpio: can't dispatch IRQs from modules
gpiochip_add: registered GPIOs 192 to 209 on device: twl4030
Unable to handle kernel paging request at virtual address b82a4c74
...
Additionally if this does not fail, warnings are produced
about trying to register the MMC multiple times.
Fix this by removing __init from omap_mux_get_by_name,
and add checks if omap2_hsmmc_init() is getting called more
than once.
Note that this will get fixed properly later on by splitting
omap2_hsmmc_init into two functions.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QYVn
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
Driver at91_ide is broken and should not be fixed: remove it.
Modification of device files that where making use of it. The
PATA driver (pata_at91) is able to replace at91_ide.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
SMC, Static Memory Controller will need more accessors to fine
configure its parameters.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Registration of at91_udc as a module will enable SoC
related code.
Fix following an idea from Karel Znamenacek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Karel Znamenacek <karel@ryston.cz>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While trying to debug my OMAP platforms, they emitted this message:
omap_hwmod: %s: enabled state can only be entered from initialized, idle, or disabled state
The following backtrace said it was from a function called '_enable',
which didn't provide much clue. Grepping didn't find it either.
The message is wrapped, so unwrap the message so grep can find it. Do
the same for three other messages in this file.
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous commit causes new section mismatch warnings:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb30): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb4c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb60): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb6c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb78): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb90): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb9c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdba8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbc0): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbcc): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbd8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbf8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc04): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc10): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc28): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc34): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc40): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc58): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc64): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc70): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc7c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Again, as for omap2_hsmmc_init(), these functions are callable at
runtime via the gpio-twl4030.c driver, and so these can't be marked
__init.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.
Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x1c664): Section mismatch in reference from the function omap_secondary_startup() to the function .cpuinit.text:secondary_startup()
The function omap_secondary_startup() references
the function __cpuinit secondary_startup().
This is often because omap_secondary_startup lacks a __cpuinit
annotation or the annotation of secondary_startup is wrong.
Unfortunately, fixing this causes a new warning which is harder to
solve:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x5328): Section mismatch in reference from the function omap4_hotplug_cpu() to the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
because omap4_hotplug_cpu() is used by power management code as well,
which may not end up using omap_secondary_startup().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Found by review.
omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.
The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().
So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15a4): Section mismatch in reference from the function omap_mux_init_signals() to the function .init.text:omap_mux_init_signal()
The function omap_mux_init_signals() references
the function __init omap_mux_init_signal().
This is often because omap_mux_init_signals lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On my OMAP4 platform, I'm getting this error message repeated several
times at boot:
omap_vc_i2c_init: I2C config for all channels must match.
omap_vc_i2c_init: I2C config for all channels must match.
This doesn't help identify what the problem is. Fix this message to
be more informative:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
This allows us to identify which voltage domains have a problem, and
what the I2C configuration state (a boolean, i2c_high_speed) setting
being used actually is.
From this we find that omap4_core_pmic has i2c_high_speed false, but
omap4_iva_pmic and omap4_mpu_pmic both have it set true.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While testing on my OMAP3430 platform, this error message was emitted:
omap_vc_init_channel: PMIC info requried to configure vc forvdd_core not populated.Hence cannot initialize vc
Trying to find this message was difficult because it was wrapped across
several lines. It also mis-spells "required", doesn't read very well,
and has spaces lacking. Let's replace it with a more concise:
omap_vc_init_channel: No PMIC info for vdd_core
While we're here, fix a simple spelling error in a comment.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_OF is disabled, the compile fails with:
arch/arm/mach-omap2/prm44xx.c:41: error: 'OMAP44XX_IRQ_PRCM' undeclared here (not in a function)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build breakage due to the following commits:
Commit bd5f12a247
ARM: 7042/3: mach-ep93xx: break out GPIO driver specifics
Commit 257af9f972
ARM: 7041/1: gpio-ep93xx: hookup the to_irq callback in the driver
The vision_ep9307 machine uses the ep93xx build-in gpios and needs to
include <mach/gpio-ep93xx.h> to pickup the defines.
The gpio_to_irq() call is now a callback to the gpio-ep93xx.c driver
and cannot be used as a constant initializer for the .irq member of
struct i2c_board_info.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit
4af4016c53 ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
