* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6870/1: The mandatory barrier rmb() must be a dsb() in for device accesses
ARM: 6892/1: handle ptrace requests to change PC during interrupted system calls
ARM: 6890/1: memmap: only free allocated memmap entries when using SPARSEMEM
ARM: zImage: the page table memory must be considered before relocation
ARM: zImage: make sure not to relocate on top of the relocation code
ARM: zImage: Fix bad SP address after relocating kernel
ARM: zImage: make sure the stack is 64-bit aligned
ARM: RiscPC: acornfb: fix section mismatches
ARM: RiscPC: etherh: fix section mismatches
We enabled write-combining for memory-mapped registers in commit
65f0b417de, but inhibited it for the
MCDI shared memory where this is not supported. However,
write-combining mappings also allow read-reordering, which may also
be a problem.
I found that when an SFC9000-family controller is connected to an
Intel 3000 chipset, and write-combining is enabled, the controller
stops responding to PCIe read requests during driver initialisation
while the driver is polling for completion of an MCDI command. This
results in an NMI and system hang. Adding read memory barriers
between all reads to the shared memory area appears to reduce but not
eliminate the probability of this.
We have not yet established whether this is a bug in our BIU or in the
PCIe bridge. For now, work around by mapping the shared memory area
separately.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Start/stop TX queue is controlled by TX queue "used" counter.
It is incremented while WRBs are posted to TX queue and
decremented when TX completions are received. This counter was
getting decremented before HW is informed about processing of TX
completions. As used counter is decremented, transmit function
posts new WRBs and creates completion queue full scenario in HW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use OPCODE_COMMON_NTWK_RX_FILTER command for promiscous mode as
OPCODE_ETH_PROMISCUOUS command is getting deprecated.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UE, do not dump registers for Lancer as they are not
supported.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable coalesce water mark mode of CQ for Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Lancer if a frame is DMAed partially due to lack of RX buffers,
an error completion is sent with packet size as zero and num_recvd
indicating number of used buffers. These buffers need to be freed
and packet dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows individual users and deployments to disable mesh support at
runtime, i.e. without having to build and maintain a custom kernel.
Based on a patch by Paul Fox <pgf@laptop.org>.
Signed-off-by: Sascha Silbe <silbe@activitycentral.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some structures and macros in ioctl.h are redundant or no longer
used.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid use of local structure in the function if the structure is
already allocated by the caller and the structure pointer is passed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not N-PHY specific function, we partially duplicate code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in 2.6.39-rc1 it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh beaconing on ath9k was broken by this commit:
commit 4801416c76
Author: Ben Greear <greearb@candelatech.com>
Date: Sat Jan 15 19:13:48 2011 +0000
This patch assigns the right opmode when the device is used in mesh
mode.
Reported-by: Fabrice Deyber fabricedeyber@agilemesh.com
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the more descriptive logging styles gives a bit
more information about the device being operated on.
Makes the object trivially smaller too.
$ size drivers/net/wireless/libertas/built-in.o.*
187730 2973 38488 229191 37f47 drivers/net/wireless/libertas/built-in.o.new
188195 2973 38488 229656 38118 drivers/net/wireless/libertas/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard pr_<level> functions eases grep a bit.
Added a few missing terminating newlines to messages.
Coalesced long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure definition is
struct mwifiex_opt_sleep_confirm_buffer {
u8 hdr[4];
struct mwifiex_opt_sleep_confirm ps_cfm_sleep;
} __packed;
For sleep_confirm command we already reserve 4 bytes (using skb_reserve())
for an interface header. It will be filled later by interface specific code.
We don't need "hdr[4]" element in above structure. So we can use
"struct mwifiex_opt_sleep_confirm" directly instead of
"struct mwifiex_opt_sleep_confirm_buffer".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This beacon rssi will be used to set noisefloor during ani reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The average beacon rssi which will be used by ani is not updated
in adhoc mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By changing DCU backoff threshold for AR9340 to 1, helps to
reduce rx overrurns seen while running bidirectional traffic.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Found via coccinelle script
@@
type T;
T* ptr;
expression E1;
@@
* memset(E1, 0, sizeof(ptr));
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently ath9k_hw_getchan_noise is not used anywhere
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be helpful when we decide to add support for other buses.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch:
- adds kfree() where necessary
- prevents potential null dereferences
- makes use of kfree_skb()
- replaces -1 for failed kzallocs with -ENOMEM
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Kiran Divekar <dkiran@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code to detect inactive 802.11 cores, as that function is now done
in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code to detect inactive 802.11 cores, as that function is now done
in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txstatus_timer should only be deleted for USB devices, as it is only
initialized for USB devices.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54pci.c: In function ‘p54p_tx’:
p54pci.c:334:6: warning: variable ‘device_idx’ set but not used
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx.c: In function ‘carl9170_tx_accounting_free’:
tx.c:159:28: warning: variable ‘txinfo’ set but not used
tx.c: In function ‘carl9170_tx_status_process_ampdu’:
tx.c:383:27: warning: variable ‘ar_info’ set but not used
tx.c: In function ‘__carl9170_tx_process_status’:
tx.c:626:27: warning: variable ‘arinfo’ set but not used
tx.c: In function ‘carl9170_tx_ampdu_queue’:
tx.c:1324:15: warning: variable ‘max’ set but not used
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this driver was initially submitted, the system would crash unless
ASPM was disabled. This problem has been fixed.
This patch also adds a printk that outputs the name of the firmware
file that is used.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In driver rtlwifi, efuse_read() places two relatively large arrays on the
stack - a 1D u8 array of size 128, and a 2D array of u16 with 128 * 4 elements.
With driver rtl8192de, the sizes will be 256 and 256 * 4 respectively. As that
will make the 2D array be 2048 bytes, I have changed the code to use kmalloc to
allocate the space.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function iwl_is_any_associated() was intended
to check both contexts, but due to an oversight
it only checks the BSS context. This leads to a
problem with scanning since the passive dwell
time isn't restricted appropriately and a scan
that includes passive channels will never finish
if only the PAN context is associated since the
default dwell time of 120ms won't fit into the
normal 100 TU DTIM interval.
Fix the function by using for_each_context() and
also reorganise the other functions a bit to take
advantage of each other making the code easier to
read.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 5ed540aecc change the led behavior
for iwlwifi driver; the side effect cause led blink all the time.
Modify the led blink table to fix this problem
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We occasionally see list corruption using libertas.
While we haven't been able to diagnose this precisely, we have spotted
a possible cause: cmdpendingq is generally modified with driver_lock
held. However, there are a couple of points where this is not the case.
Fix up those operations to execute under the lock, it seems like
the correct thing to do and will hopefully improve the situation.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not switch to non-IBSS channels when working in IBSS mode,
otherwise there are microcode errors, and after some time system
crashes.
This bug is only observable when software scan is used in IBSS mode,
so should be considered as regression after:
commit 0263aa4529
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Tue Mar 29 11:24:21 2011 +0200
iwl3945: disable hw scan by default
However IBSS mode check, which this patch add again, was removed by
commit b2f30e8bdd
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Jan 21 07:32:20 2010 -0800
iwlwifi: remove IBSS channel sanity check
That commit claim that mac80211 will not use non-IBSS channel in IBSS
mode, what definitely is not true. Bug probably should be fixed in
mac80211, but that will require more work, so better to apply that patch
temporally, and provide proper mac80211 fix latter.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=34452
Reported-and-tested-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: stable@kernel.org # 2.6.38.5+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/S3 state drv_flush is called from mac80211 irrespective of
interface count. In ath9k we queue a work in ath9k_flush which we expect
to be cancelled in the drv_stop call back. during suspend process mac80211
calls drv_stop only when the interface count(local->count) is non-zero.
unfortunately when the network manager is enabled, drv_flush is called
while drv_stop is not called as local->count reaches '0'.
So fix this by simply checking for the device presence in the
drv_flush call back in the driver before queueing work or anything else.
this patch fixes the following WARNING
Call Trace:
[<c014c6e2>] warn_slowpath_common+0x72/0xa0
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[<fc133f99>] ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc134ed1>] ieee80211_queue_delayed_work+0x21/0x50 [mac80211]
[<fc1e5b22>] ath_tx_complete_poll_work+0xb2/0x100 [ath9k]
[<c016399e>] run_workqueue+0x8e/0x150
[<fc1e5a70>] ? ath_tx_complete_poll_work+0x0/0x100 [ath9k]
[<c0163ae4>] worker_thread+0x84/0xe0
[<c0167a60>] ? autoremove_wake_function+0x0/0x50
[<c0163a60>] ? worker_thread+0x0/0xe0
[<c01677d4>] kthread+0x74/0x80
[<c0167760>] ? kthread+0x0/0x80
[<c0104087>] kernel_thread_helper+0x7/0x10
---[ end trace 2aff81010df9215b ]---
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert logging messages to more current styles.
Added -DDEBUG to Makefile to maintain current message logging.
This could be converted to a specific CONFIG_TULIP_DEBUG option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current more descriptive logging styles.
Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the blocks that are guarded by #if DEBUG to
be #if defined DEBUG && DEBUG > 1 so that pr_debug
can be used later.
Remove enter/leave macros and uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.
mac_pton() doesn't dirty result until it's sure string representation is valid.
mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.
mac_pton() diverges from 0/-E return value convention.
Target usage:
if (!mac_pton(str, whatever->mac))
return -EINVAL;
/* ->mac being u8 [ETH_ALEN] is filled at this point. */
/* optionally check str[3 * ETH_ALEN - 1] for termination */
Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull read_lock(&bond->lock) and BOND_IS_OK() to bond_start_xmit() from
mode-dependent xmit functions.
netif_running() is always true in hard_start_xmit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unknown 8168 chips did not have any PLL power method set as they
did not inherit a default family soon enough. Fix it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
- RTL_GIGA_MAC_NONE is a fake index so put it at the end of the
enumeration and shift everybody.
- RTL_GIGA_MAC_VER_17 / RTL_GIGA_MAC_VER_16 ordering fixed. Though
not wrong it was confusing enough to wonder if things were right.
Renaming rtl_chip_info was not strictly necessary. It allows to
check the patch for the correct use of the indexes though.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Invocation of rtl8169_rx_interrupt from rtl8169_reset_task was originally
intended to retrieve as much packets as possible from the rx ring when a
reset was needed. Nowadays rtl8169_reset_task is only scheduled, with
some delay
a. from the tx timeout watchdog
b. when resuming
c. from rtl8169_rx_interrupt itself
It's dubious that the loss of outdated packets will matter much for a)
and b). c) does not need to call itself again.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
The implementation was a bit krusty.
The 10s rtl8169_phy_timer timer has been (was ?) required with older
8169 for adequate phy operation when full gigabit is advertised in
autonegotiated mode. The timer does nothing if the link is up.
Otherwise it keeps resetting the phy until things improve.
- the device private data field phy_1000_ctrl_reg was used to
schedule the timer. Avoid it and save a few bytes.
- rtl8169_set_settings
pending timer is disabled before changing the link settings as
rtl8169_phy_timer is not always needed (see the removed test in
rtl8169_phy_timer).
- rtl8169_set_speed
the requested link parameters may not match the chipset : bail out
early on failure.
- rtl8169_open
Calling rtl8169_request_timer is redundant with
-> rtl8169_open
-> rtl8169_init_phy
-> rtl8169_set_speed
-> mod_timer
The latter always enables the phy timer whereas the former did not
for RTL_GIGA_MAC_VER_01. It should not make things worse but only
time will tell if reality agrees.
- rtl8169_request_timer : unused yet. Removed.
- rtl8169_delete_timer : useless. Bloat. Removed.
Side effect : the timer may kick in if the TBI is enabled. I do not
know if the TBI has ever been used in real life.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Shorten chipset version test.
No functional change.
Careful readers will notice that the 'supports_gmii' flag is deduced
from the device PCI id. Though less specific than the chipset related
RTL_GIGA_MAC_VER_XY, it is good enough to detect a GMII deprieved 810x.
Some features push for a device specific configuration (improved jumbo
frame support for instance). 'supports_gmii' will follow this path
if / when the device PCI id test stops working.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
The checksum judgment was mistaken.
Judgment result
0:Correct 1:Wrong
This patch fixes the issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The collision detection setting was invalid.
When collision occurred, because data was not resent,
there was an issue to which a transmitting throughput falls.
This patch enables the collision detection.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TTY layer expects 0 if the ldisc->open operation succeeded.
Signed-off-by : Matvejchikov Ilya <matvejchikov@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed bug to make sure 'pvid' retrieval will work on big endian hosts.
Fixed incorrect comparison between the Rx Completion's 16-bit VLAN TCI
and the PVID. Now comparing only the relevant 12 bits corresponding to
the VID.
Renamed 'vid' field under Rx Completion to 'vlan_tag' to reflect
accurate description.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently EHEA reports to ethtool as supporting 10M, 100M, 1G and
10G and connected to FIBRE independent of the hardware configuration.
However, when connected to FIBRE the only supported speed is 10G
full-duplex, and the other speeds and modes are only supported
when connected to twisted pair.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth devices dont use the batched device unregisters yet.
Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.
Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)
This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.
Following set of commands illustrates one such example -
a) ip -4 addr add 192.168.1.1/24 dev eth1
b) ip -4 rule add from all iif eth1 lookup 250
c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
d) arp -Ds 192.168.1.100 eth1
e) arp -Ds 192.168.1.200 eth1
f) sysctl -w net.ipv4.ip_nonlocal_bind=1
g) sysctl -w net.ipv4.conf.all.accept_local=1
# Assuming that the machine has 8 cores
h) taskset 000f netserver -L 192.168.1.200
i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB protocol this driver implements appears to require 2 bytes of
padding in front of each received packet. This used to be equal to
the value of NET_IP_ALIGN on x86, so the driver abused that constant
and mostly worked, but this is no longer the case. The driver also
mixed up the URB and packet lengths, resulting in 2 bytes of junk at
the end of the skb.
Introduce a private constant for the 2 bytes of padding; fix this
confusion and check for the under-length case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback macvlan_port_rcu_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(macvlan_port_rcu_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback ring_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ring_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
I deleted it by mistake in the TX_CHECKSUM removal
commit.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OS2BMC registers are available for X540.
This patch adds ethtool counters based on those registers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on patch from Stephen Hemminger.
Convert igb driver to use new set_phys_id ethtool interface.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Stephen Hemminger.
Convert to new LED control infrastucture and remove no longer
necessary bits.
CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Stephen Hemminger.
Implement set_phys_id to control LED.
CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TX checksumming support has been ifdef commented out of this driver
for more than 10 years, and it makes references to aspects of the IPv4
stack from back then as well.
If someone has one of these rare cards and wants to properly resurrect
TX checksumming support, they can still get at this code in the
version control history.
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA mappings can fail, but the current code
doesn't check for that. Add checking, which
requires some restructuring for proper error
paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All AGN devices need the bytecount table, so
remove the indirection and make the functions
static again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The device doesn't use the bytecount table for the
command queue, only for aggregation queues to make
aggregation decisions. So don't update it for the
command queue (and we even updated it with wrong
values).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The variable 'len' here is set but never used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The frame pre-allocation is quite a bit of complex
code, all to avoid a single allocation. Remove it
and consolidate the beacon sending code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no need for this, all commands are the right size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch adds the feature to support the test mode operation through
the generic netlink channel NL80211_CMD_TESTMODE between intel
wireless device iwlwifi and the user space application svtool.
The main purpose is to create a transportation layer between the iwlwifi
device and the user space application so that the interaction between the
user space application svtool and the iwlwifi device in the kernel space is
in a way of generic netlink messaging.
The detail specific functions are:
1. The function iwl_testmode_cmd() is added to digest the svtool test command
from the user space application. The svtool test commands are categorized to
three types : commands to be processed by the device ucode, commands to access
the registers, and commands to be processed at the driver level(such as reload
the ucode). iwl_testmode_cmd() dispatches the commands the corresponding handlers
and reply to user space regarding the command execution status. Extra data is
returned to the user space application if there's any.
2. The function iwl_testmode_ucode_rx_pkt() is added to multicast all the spontaneous
messages from the iwlwifi device to the user space. Regardless the message types,
whenever there is a valid spontaneous message received by the iwlwifi ISR,
iwl_testmode_ucode_rx_pkt() is invoked to multicast the message content to user
space. The message content is not attacked and the message parsing is left to
the user space application.
Implementation guidelines:
1. The generic netlink messaging for iwliwif test mode is through NL80211_CMD_TESTMODE
channel, therefore, the codes need to follow the regulations set by cfg80211.ko
to get the actual device instance ieee80211_ops via cfg80211.ko, so that the iwlwifi
device is indicated with ieee80211_ops and can be actually accessed.
Therefore, a callback iwl_testmode_cmd() is added to the structure
iwlagn_hw_ops in iwl-agn.c.
2. It intends to utilize those low level device access APIs from iwlwifi device driver
(ie. iwlagn.ko) rather than creating it's own set of device access functions.
For example, iwl_send_cmd(), iwl_read32(), iwl_write8(), and iwl_write32() are reused.
3. The main functions are maintained in new files instead of spreading all over the
existing iwlwifi driver files.
The new files added are :
drivers/net/wireless/iwlwifi/iwl-sv-open.c
- to handle the user space test mode application command
and reply the respective command status to the user space application.
- to multicast the spontaneous messages from device to user space.
drivers/net/wireless/iwlwifi/iwl-testmode.h
- the commonly referenced definitions for the TLVs used in
the generic netlink messages
Signed-off-by: Cindy H. Kao <cindy.h.kao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WARNING: drivers/net/arm/built-in.o(.data+0x0): Section mismatch in reference from the variable etherh_driver to the function .init.text:etherh_probe()
The variable etherh_driver references
the function __init etherh_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Since firmware is capable of generating IV's for all crypto
suits (TKIP, CCMP and WEP), do not ask mac80211 to generate
IV when HW crypto is being used. Instead only reserve
appropriate space in tx skb's in the driver, so that the
firmware can write IV's values.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.
Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch:
rt2x00: Make rt2x00_queue_entry_for_each more flexible
commit: 10e11568ca
introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.
The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Reported-by: Balint Viragh <bviragh@dension.com>
Tested-by: Balint Viragh <bviragh@dension.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add necessary RF chipset define and basic support for these devices.
Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver only disable multicast filtering when the
FIF_ALLMULTI driver flag has been just set (ie,
if changed_flags& FIF_ALLMULTI and *new_flags& FIF_ALLMULTI) or else
it will reenable multicast filtering.
But next time, this condition will be false and multicast filtering
will be reenabled, even through FIF_ALLMULTI is still set.
This mean that allmulticast only works for less than two minutes in
ad-hoc mode. This patch fixes that to disable multicast filtering
as long as FIF_ALLMULTI is set.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WEP key length was being set to 0 erroneously which broke WEP support.
Fix the same by setting the key length appropriately.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip initialization of local variables with some default values
if the values are not going to be used further down the code path.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scan and assoc (infra/ibss) commands are simultaneously
given in two terminals, association response is erroneously
served while serving the scan response.
mwifiex_cfg80211_results() is the common routine for sending
ioctl (scan, assoc etc.) results to cfg80211 stack. In above
scenario even if the common routine is called for scan ioctl
context, it also tries to send information about assoc ioctl to
cfg80211 because "priv->assoc_request/priv->ibss_join_request"
flag is on at that time.
Fix the issue by updating request variable after assoc handling
and modifying the variable check in mwifiex_cfg80211_results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify rtlwifi routines for rtl8192se and set up Kconfig
and Makefile for new driver.
This patch also disables ASPM for the RTL8192SE to prevent some strange
crashes on LF's system.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines trx.c and trx.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines table.c and table.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines sw.c and sw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines rf.c and rf.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines reg.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines phy.c and phy.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines led.c and led.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines hw.c and hw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines fw.c and fw.h for RTL8192SE. In addition, make changes
to rtlwifi/wifi.h to support RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines dm.c and dm.h for RTL8192SE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce routine def.h for rtl8192se.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at http://marc.info/?l=linux-netdev&m=130428493104730&w=2
libertas frequently generates spurious tx timeouts, because the tx
queue is brought down for extended periods during scanning. The net
layer takes a look and incorrectly assumes the queue has been down for
several seconds, and generates a tx_timeout.
One way to fix this is to bump the trans_start counter while scanning
so that the network layer knows that the device is still alive, but
I think the tx_timeout handler is implemented wrongly here and not of
any real use, so I vote to remove it.
As explained at http://marc.info/?l=linux-wireless&m=130430311115755&w=2
the watchdog is primarily meant to deal with lockup on the hardware TX
path (detected by the tx queue being stopped for an extended period of
time), but this is unlikely to happen with libertas. In this case, the tx
queue is stopped only while waiting for lbs_thread to send the queued frame
to the driver, and lbs_thread wakes up the queue immediately after, even
if the frame could not be sent correctly.
So, the only hardware-related possibility that this catches is if
hw_host_to_card hangs - this is something I have never seen. And if it
were to happen, nothing done by lbs_tx_timeout would actually wake up
lbs_thread any quicker than otherwise.
Removing this oddly-behaving spuriously-firing tx_timeout handler should
fix an occasional kernel crash during resume
(http://dev.laptop.org/ticket/10748)
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.
This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTR frames do have a valid data length code on CAN.
The driver for SJA1000 did not handle that situation properly.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid link notification duplication
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Karim Hamiti <karim.hamiti@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe connections should be expressed as GT/s (GigaTransfers per second)
instead of the current Gb/s (Gigabits per second). In addition, it is
incorrect because (due to PCIe gen 1 & 2 having a 20% overhead) the
actually data rate, when expressed in Gb/s, is only 80% of the rate of
GT/s.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce buffered read/writes which greatly improves performance on
parts with large EEPROMs.
Previously reading/writing a word requires taking/releasing of synchronization
semaphores which adds 10ms to each operation. The optimization is to
read/write in buffers, but make sure the semaphore is not held for >500ms
according to the datasheet.
Since we can't read the EEPROM page size ixgbe_detect_eeprom_page_size() is
used to discover the EEPROM size when needed and keeps the result in
word_page_size for the rest of the run time.
Use buffered reads for ethtool -e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: symbol 'before' shadows an earlier one
Convert large macros to functions similar to e1000e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correcting a simple typo with enabling software defined pins. I don't
believe this was causing any issues but this is how it was meant to be
implemented.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change remaining direct calls to function pointers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device lies about supporting phys_id. Remove it and just
let the upper layer report not supported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent commits have changed how EEPROM size is checked and if the size
word is misconfigured, the driver will fail to load. This patch adds a
check for invalid size word in the EEPROM and uses default size instead
for 82576 parts.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch sent by Stephen Hemminger.
This version incorporates the ethtool changes that Bruce Allan
submitted.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
They are only applicable for locally-homecached memory ranges, so
change their names to {flush,finv}_buffer_local(). Change inv_buffer()
to just do an mf instead of any kind of fancier barrier, since you're
obviously not going to be waiting for anything once the local homecache
is invalidated.
Fix tilepro.c network driver not to bother calling finv_buffer when
stopping the EPP, but just mf after memset to ensure that it will not
see any packet data after we finish stopping; use finv_buffer_remote()
when doing exit-time cleanup.
This also fixes a (not very interesting) generic Linux build failure
where drivers/scsi/st.c declares its own flush_buffer().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
84c49d8c3e ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter. Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mwifiex_cmd_append_tsf_tlv(), two tsf_val TLVs should be
filled in the buffer and then sent to firmware.
The missing first TLV for tsf_val is added back in this patch.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB drivers don't support automatically waking up when in powersaving mode,
add a work object which will wakeup the device in time to receive the next beacon.
Based on that beacon, we either go back into powersaving mode, or we remain awake
to receive the buffered frames for our station.
Some part of the code, especially rt2x00lib_find_ie and rt2x00lib_rxdone_check_ps
are inspired on the code from carl9170.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use flag instead of re-reading the eeprom every time.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800lib.c the rt2800_init_eeprom function the same eeprom
words were read multiple times, due to inefficient ordering of the
eeprom checks.
Reorder the checks so that each EEPROM word only has to be read once.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch
rt2x00: Optimize register access in rt2800pci
from Helmut Schaa missed one register call, namely
the rt2800_register_multiwrite which should be changed
to rt2x00pci_register_multiwrite.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add recycling functionality to rt2x00usb_register_read_async.
When the callback function returns true, resubmit the urb to
read the register again.
This optimizes the rt2800usb driver when multiple TX status reports
are pending in the register, because now we don't need to allocate
the rt2x00_async_read_data and urb structure each time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no TX status was available, the default timeout
of 20ms is a bit high. The frame is highly likely already
send out, so the TX status should be available within
only a few milliseconds.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By reading the "driver_state" debugfs value we get all the important
state information from the wl12xx driver. This helps testing and
debugging, particularly in situations where the driver seems "stuck".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP, the TX queues are not stopped when we start
recovery. mac80211 is notified only after the fact. When there is
pending TX, it will be queued even after the FW is down. This leads to
situations where the TX queues are stopped (because of the TX-watermark
mechanism), and are never woken up when we return from recovery.
Fix this by explicitly stopping the TX queues when before initiating
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This entry is useful for debugging the driver state machine during
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When there's a change in the basic rates of the AP, reconfigure relevant
templates with the new rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.
When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.
Unify rate configuration on initialization and on change notification
into a single function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When performing recovery, print the firmware version and program
counter (by reading the SCR_PAD4 register). The value of the firmware
program counter during assert can be useful for debugging.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We use a long timeout (2 seconds) when sending commands to the FW.
When a command times out, it means the FW is stuck, and we should
commence recovery.
This should make recovery times shorter as we'll recover on the first
timeout indication.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New AP-mode FWs filter external beacons by default. Disable this
filtering on start up so we can properly configure ERP protection.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the wiphy RTS and fragmentation thresholds for initializing the FW
when possible. This mitigates a bug where previously set values are
forgotten after interface down/up.
Add checks before settings these values to ensure they are valid. Use
default values when invalid thresholds are configured.
Update the default RTS threshold to the maximum value given by the
specification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize AP specific BT coexitance parameters to default values and
enable them in AP mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is preferred to use the setter that to set queue_mapping directly.
This also helps backporting in compat-wireless.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When packets arrive with a RX descriptor indicating corruption, discard
them.
In general white-list the RX descriptor status to prevent rouge data
from being sent up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames are considered pending when they reside in the driver TX queue or
already queued in the FW.
This notion of "pending" is appropriate for power save considerations in
STA mode, but not necessarily in other modes (for instance P2P-GO).
[Fixed a sparse warning about missing "static" in a function
declaration -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW can dynamically manage its internal TX & RX memory pools, moving
blocks from one pool to another when necessary. This can significantly
improve performance. Currently this feature is enabled only for 128x.
Enable dynamic memory for 127x as well. Other parameters in the memory
configuration structure may need to be fine tuned, as the optimal values
for these may change once dynamic memory is enabled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver stops sending TX packets when either there aren't enough
memory blocks, or it runs out of TX descriptors. The driver continues to
send packets to the FW only when more memory blocks are available.
The FW might free TX descriptors without freeing the corresponding
memory blocks, especially when dynamic memory is enabled. In cases where
memory blocks are not freed at all, the driver will keep waiting for
more memory blocks indefinitely.
Fix this by clearing the WL1271_FLAG_FW_TX_BUSY flag when there are
available TX descriptors.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 128x/AP firmware does not yet support dynamic memory. Temporarily,
the memory configuration for the 127x was used both for 127x/AP as well
as 128x/AP. Since the two chips don't have the same number of memory
blocks, TP was significantly degraded.
This hasn't been fine tuned yet, but using the base 128x numbers
(without dynamic memory) seems to yield much better results (around 30%
more). Additional fine tuning will be required in the future.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When configuring ACX_WAKE_UP_CONDITIONS (before entering psm), we
tell the firmware to wake up once in N DTIMs/beacons.
Allow control of this value via debugfs (for debugging purposes).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reducing the retries of sending PS exit packets to the peer AP.
That fix is to avoid sending unrealizable number of PS exit packets
in case of ap lost.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to FM WLAN coexistence (STA only). Some WiFi harmonics
may interfere with FM operation, to avoid this problem special
coexistence techniques are activated around some FM frequencies.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When working in ibss mode, we don't configure rate policy per station
(as we use the same link for multiple stations), so currently the
1mb/s rate is being used.
Instead, configure the firmware to use the whole 11b rates by default.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee80211_reconfig() sets most of the "changed" flags regardless
of the actual change (e.g. BSS_CHANGED_ASSOC will be set even if
the interface is still not associated). in this case the driver
will issue some unneeded commands.
Since the driver relies solely on the BSS_CHANGED_ASSOC flag,
without checking if there was an actual change, it will end up
issuing unjoin() and dummy_join() commands, although it was
never associated and should just remain idle.
Avoid it by checking the actual state change, in addition to the
"changed" flag.
(there seem to be more redundant configuration commands being
issued, but they shouldn't harm)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When debugging, reduce the padding size from each rx packet, to
get the actual packet size (so comparing it against a cap file
will be easier)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix mismatch between the REF CLK and TCXO CLK information that is
set in the platform data and the NVS, so we override what comes
from the NVS and replace it with what comes from the platform data.
[Small fix in a comment -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The elp_work is being enqueued on wl1271_ps_elp_sleep, but doesn't get
cancelled on wl1271_ps_elp_wakeup. This might cause immediate entrance
to elp when the wl->mutex is being released, rather than using the delayed
enqueueing optimization.
Cancel elp_work on wakeup request, and add a new WL1271_FLAG_ELP_REQUESTED
flag to further synchronize the elp actions.
[Fixed a couple of typos in some comments -- Luca]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit d05c806 ("wl12xx: rearrange some ELP wake_up/sleep calls")
introduced a bug in which wl1271_ps_elp_wakeup() was called instead
of wl1271_ps_elp_sleep() after completing the tx work.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
End-of-transaction flag should be set when working with
wl127x chip on AP mode.
Thanks Ido Yariv <ido@wizery.com> for the guidance with that.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If an interface type changes from a type that is
only supported on the PAN context (e.g. P2P GO)
to a type that is supported on the BSS context,
and the BSS context is not in use, then we need
to use the BSS context instead of changing the
device type within the context. To achieve this,
refuse the type change, which causes a down/up
cycle that will allocate the BSS context for the
interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current RXON checking doesn't verify that
the channel is valid (or at least non-zero),
so add that. Also, add a WARN() so we get a
stacktrace, and capture a bitmask of errors
in order to capture all necessary information
in the warning itself (in case the previous
messages are snipped off.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This header file isn't used, and if we ever need
these definitions they shouldn't be added to a
driver but rather to the common 802.11 include
file that has all frame definitions. Thus, just
remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All agn devices use the same eeprom semaphore and calib version routines.
Delete the indirection and move the semaphore routines to where they are
used and make static.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All agn devices use the same module parameter structure. Delete the
indirection and access the structure diretly.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
New microcode versions use the good CRC threshold
field differently, as a flag, and in that case we
should set it to 1/0 instead of 1/65535 for an
active/passive scan.
The new behaviour is advertised by the uCode with
a feature flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
No functional changes, separate the connect and disconnect sequences in
RXON commit function, easier to read and understand.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The WoWLAN resume code will have to essentially
do a restart, but without going through the work
struct. To support that, refactor the restart by
splitting out the preparation code into a new
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a few cases like the WoWLAN support
I'm writing that require attempting to access
the NIC when it is known that it might not be
accessible, e.g. after the system woke up and
the platform might have reset the device.
To avoid messages in this case, introduce the
new function iwl_grab_nic_access_silent(), it
will only return an error status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If a device error happens while the uCode is
being loaded or initialised, we will attempt
to restart the device (which will likely fail
again, but that's not the issue here). During
this new restart, we turn off the device, but
as the uCode failed to initialise it already
is turned off. As a consequence, grabbing NIC
access will fail and cause excessive messages
and hangs.
To fix this issue, introduce a new status bit
and only attempt to reprogram the device when
it isn't already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This makes sure that one cannot request a 99Mbps full-duplex and get a
100Mbps half-duplex configuration in return due to the way the
speed/duplex parameters are handled internally.
Tested: e1000 works
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial driver reported different speeds depending on the port being
used. This advertises the speed to be 10Mbps in any case, which is
what it actually is on the wire.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tells the NIC to take the speed specified by ethtool into account
when configuring the NIC, instead of keeping the previous speed.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of pause frames advertise in mii_get_an. This provides all drivers
that use mii_ethtool_gset to represent their own and Link partner flow control
abilities in ethtool.
Signed-off-by: Artem Polyakov <artpol84@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.
o Update driver version to 5.0.17.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.
Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.
Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested. Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter. Bump
the bonding version number and update its documentation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adam Jaremko <adam.jaremko@gmail.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some newer Huawei devices (T-Mobile Rocket, others) have cdc-ether
compatible ports, so recognize and expose them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_headroom required for mwl8k driver is 32 bytes and it
can use the space for 802.11 header received from mac80211.
mwl8k considers the smallest 802.11 frame (CTS2self of 10
bytes) that can be received from mac80211 to compute the
extra_tx_headroom as 22 (32 - 10) bytes.
When the wireless interface is part of bridge, this
extra_tx_headroom requirement results in a memcpy in
mac80211 (in function pskb_expand_head) for all the data
frames needing L2 forwarding/bridging, when NET_SKB_PAD is
defined as 32. This patch reduces the extra_tx_headroom by
8 bytes so that memcpy of data frames in mac80211 is
avoided in this case.
The resize will be required in driver for frames with 802.11
header size of less than 18 bytes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
Do not change callback, I did (and fixed) that mistake in iwlagn.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't need to use conditional as ch->band is already assigned to
IEEE80211_BAND_5GHZ or IEEE80211_BAND_2GHZ
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add two below iwlwifi commits to iwlegacy:
commit 554d1d027b
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Dec 23 12:38:21 2010 +0100
iwlagn: enable only rfkill interrupt when device is down
commit 3dd823e6b8
Author: Don Fry <donald.h.fry@intel.com>
Date: Sun Feb 6 09:29:45 2011 -0800
iwlagn: Re-enable RF_KILL interrupt when down
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since
commit f844a709a7
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Jan 28 16:47:44 2011 +0100
iwlwifi: do not set tx power when channel is changing
we set device tx power during initialization to priv->tx_power_next,
which itself is initialized to minimum power. That changed
default behaviour of driver. Previously we initialized device to
transmit at maximum available power by default. Patch change again
to previous behaviour and cleanup tx power initialization.
Fortunately this is not critical fix, as mac80211 layer setup
tx power lately to 14dB, hence device does not operate at minimal
transmit power all the time.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This oops was recently reported to me:
invalid opcode: 0000 [#1] SMP
last sysfs file:
/sys/devices/pci0000:00/0000:00:01.0/0000:01:0d.0/0000:02:05.0/device
CPU 1
Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]
Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]
Pid: 23900, comm: pidof Not tainted 2.6.32-130.el6.x86_64 #1 BladeCenter LS21
-[797251Z]-
RIP: 0010:[<ffffffffa058b270>] [<ffffffffa058b270>] 0xffffffffa058b270
RSP: 0018:ffff880002083e48 EFLAGS: 00010246
RAX: ffff880002083e90 RBX: ffff88007ccd4000 RCX: 0000000000000000
RDX: 0000000000000100 RSI: dead000000200200 RDI: ffff8800007b8700
RBP: ffff880002083ed0 R08: ffff88000208db40 R09: 0000022d191d27c8
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800007b9bc8
R13: ffff880002083e90 R14: ffff8800007b8700 R15: ffffffffa058b270
FS: 00007fbb3bcf7700(0000) GS:ffff880002080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000001664a98 CR3: 0000000060395000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process pidof (pid: 23900, threadinfo ffff8800007e8000, task ffff8800091c0040)
Stack:
ffffffff81079f77 ffffffff8109e010 ffff88007ccd5c20 ffff88007ccd5820
<0> ffff88007ccd5420 ffff8800007e9fd8 ffff8800007e9fd8 0000010000000000
<0> ffff88007ccd5020 ffff880002083e90 ffff880002083e90 ffffffff8102a00d
Call Trace:
<IRQ>
[<ffffffff81079f77>] ? run_timer_softirq+0x197/0x340
[<ffffffff8109e010>] ? tick_sched_timer+0x0/0xc0
[<ffffffff8102a00d>] ? lapic_next_event+0x1d/0x30
[<ffffffff8106f737>] __do_softirq+0xb7/0x1e0
[<ffffffff81092cc0>] ? hrtimer_interrupt+0x140/0x250
[<ffffffff81185f90>] ? filldir+0x0/0xe0
[<ffffffff8100c2cc>] call_softirq+0x1c/0x30
[<ffffffff8100df05>] do_softirq+0x65/0xa0
[<ffffffff8106f525>] irq_exit+0x85/0x90
[<ffffffff814e3340>] smp_apic_timer_interrupt+0x70/0x9b
[<ffffffff8100bc93>] apic_timer_interrupt+0x13/0x20
<EOI>
[<ffffffff81211ba5>] ? selinux_file_permission+0x45/0x150
[<ffffffff81262a75>] ? _atomic_dec_and_lock+0x55/0x80
[<ffffffff812050c6>] security_file_permission+0x16/0x20
[<ffffffff811861c1>] vfs_readdir+0x71/0xe0
[<ffffffff81186399>] sys_getdents+0x89/0xf0
[<ffffffff8100b172>] system_call_fastpath+0x16/0x1b
It occured during some stress testing, in which the reporter was repeatedly
removing and modprobing the bnx2 module while doing various other random
operations on the bnx2 registered net device. Noting that this error occured on
a serdes based device, we noted that there were a few ethtool operations (most
notably self_test and set_phys_id) that have execution paths that lead into
bnx2_setup_serdes_phy. This function is notable because it executes a mod_timer
call, which starts the bp->timer running. Currently bnx2 is setup to assume
that this timer only nees to be stopped when bnx2_close or bnx2_suspend is
called. Since the above ethtool operations are not gated on the net device
having been opened however, that assumption is incorrect, and can lead to the
timer still running after the module has been removed, leading to the oops above
(as well as other simmilar oopses).
Fix the problem by ensuring that the timer is stopped when pci_device_unregister
is called.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Hushan Jia <hjia@redhat.com>
CC: Michael Chan <mchan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/wireless/p54/eeprom.o
drivers/net/wireless/p54/eeprom.c: In function ‘p54_parse_rssical’:
drivers/net/wireless/p54/eeprom.c:494:8: warning: ‘freq’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/mwifiex/join.o
drivers/net/wireless/mwifiex/join.c: In function ‘mwifiex_cmd_802_11_associate’:
drivers/net/wireless/mwifiex/join.c:119:8: warning: ‘tsf_val’ may be used uninitialized in this function
drivers/net/wireless/mwifiex/join.c:103:12: note: ‘tsf_val’ was declared here
Looks like a copy-n-paste error, identical lines are a few lines below
the ones removed, with an actual memcpy to tsf_val in between...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/b43/phy_n.o
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_set_channel’:
drivers/net/wireless/b43/phy_n.c:3848:47: warning: ‘tabent_r2’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:3849:47: warning: ‘tabent_r3’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_poll_rssi.clone.14’:
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$7’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$8’ may be used uninitialized in this function
FWIW, the usage of these variables is goverened by checks that match
their initializations. So, I think these are actually false warnings.
Still, I would rather avoid the warning SPAM...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath5k/reset.o
drivers/net/wireless/ath/ath5k/reset.c: In function ‘ath5k_hw_init_core_clock’:
drivers/net/wireless/ath/ath5k/reset.c💯51: warning: ‘txf2txs’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b9367bf3ee ("net: ibmveth: convert to hw_features") accidentally
removed call to ibmveth_set_csum_offload() in ibmveth_probe(). Put the
call back where it was, but with additional error checking provided
by ibmveth_set_features().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
[sfr: dev -> netdev]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Memory allocated in ETHTOOL_ACTIVE mode, is not getting freed. So,
in ETHTOOL_ID_INACTIVE mode, return after freeing allocated memory.
o Using set bit instead of blink_down field, as it is also required
in internal Loopback test and etc.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a bitmap instead of separate u32 flags allows a consistent, simpler
and more extensible mechanism to determine capabilities.
Convert bitmasks to enum.
Add tg3_flag, tg3_flag_clear and tg3_flag_set.
Convert the flag & bitmask tests.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although these are equivalent, but the skb_checksum_start_offset() is more readable.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resubmit interrupt URB if device is open. Use a flag set in
usbnet_open() to determine this state. Also kill and free
interrupt URB in usbnet_disconnect().
[Rebased off git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since timestamp in beacon buffer keeps changing all the time,
the memcmp check in mwifiex_save_curr_bcn() is redundant.
Remove that memcmp check and also avoid freeing and allocation
of buffer if required beacon buffer size is same as previous one.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Initialise HT capabilities in cfg80211 properly.
2) Cfg80211 stack may modify "sband->ht_cap" to disable
40Mhz operation in 2.4GHz band (after recent patch
"cfg80211: module_param to disable HT40 in 2.4GHz band")
Therefore read "sband->ht_cap" instead of an adapter variable
"hw_dot_11n_dev_cap" to get HT capabilities.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some SD8787 cards which don't support 5GHz band.
Therefore initialise 5GHz band parameters only if hardware
supports the band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AFAICT, this driver is claiming that 24 bits of rate info fit into a
16-bit field in the Tx descriptor. Anyway, the use of bitfields is
frowned-upon for a variety of well-documented reasons...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback is used to set the minimum rate for management
frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WMI_BITRATE_MASK_CMDID which can be
used by the set_bitrate_mask() handler.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the firmware version to 1.2
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert all libertas/ files to use kernel-doc notation instead
of whatever it was (doxygen?).
Add or fix function parameters in several places.
Use expected style for multi-line comments in lots of places.
Remove erroneous /** in multiple places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds