Driver checks if the previous dump has been cleared before taking the dump.
It doesn't take the dump if it is not cleared.
Changes from v2:
Added lock to protect dump data structures from being mangled while
dumping or setting them via ethtool.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to take FW dump.
o Driver queries FW at the init time and gets the dump template
o It takes FW dump as per the dump template
o Level of FW dump (and its size) is configured via dump flag
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.
o Update driver version to 5.0.17.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Memory allocated in ETHTOOL_ACTIVE mode, is not getting freed. So,
in ETHTOOL_ID_INACTIVE mode, return after freeing allocated memory.
o Using set bit instead of blink_down field, as it is also required
in internal Loopback test and etc.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit more than minimal conversion. There might be some issues because
of qlcnic_set_netdev_features() if it's called after netdev init.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bumped up version number to 5.0.16
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In dev->open LRO was enabled by default, enable it depending
upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaned up unused codes for interrupt coalescence settings
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made changes to VLAN code comply with new VLAN infrastructure in kernel
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Changed adapter structure to move away from embedding hardware and
receive context structs and use pointers to those objects
2. Packed all the structs that interface with FW
3. Removed unused code and structs
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak in error path of pci info.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this fix, PCI info was available only when multiple NIC functions
are present on the same port.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit d5dbda2380 "ethtool: Add
support for vlan accleration.", drivers that have NETIF_F_HW_VLAN_TX,
and/or NETIF_F_HW_VLAN_RX feature, but do not allow enable/disable vlan
acceleration via ethtool set_flags, always return -EINVAL from that
function. Fix by returning -EINVAL only if requested features do not
match current settings and can not be changed by driver.
Change any driver that define ethtool->set_flags to use
ethtool_invalid_flags() to avoid similar problems in the future
(also on drivers that do not have the problem).
Tested with modified (to reproduce this bug) myri10ge driver.
Cc: stable@kernel.org # 2.6.37+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove checks of 1 for auto_fw_reset module parameter.
auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updating module parameter after driver load is not supported
except auto_fw_reset parameter. Changing these parameter after
driver load, can have weird result.
o Update driver version to 5.0.15.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ diag test was getting executed only when both register test
and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE
flag is set.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is reading flash fw version from defined address, this address
may be invalid. Indeed Driver should read address for fw version through
flash layout table. Flash layout table has defined region and address for
fw version address should be read from fw image region.
Driver has check for old firmware, this bug can cause driver load fail.
This patch will try to read fw version from flash image region, if that fails,
read from defined address.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
Some boot code drivers dont have cleanup routine, so pci function
remains in unknown state prior to driver load. So during driver load
issue FLR unconditionally.
Update driver version to 5.0.14.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCM window register offset was calculated incorrectly for
pci function greater than zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is down, create temporary context to config LED.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver set default eswitch configuration values for PF function,
instead of validating values sent by application.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend upon reset_devices parameter
to reset the pci function as this parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the pci
function needs to be reset.
Per function refcount is maintained in driver, which is set in probe
and reset in remove handler of adapter. If the probe detects the count
as non zero then reset the function.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log LRO off message while disabling rx checksum only when
LRO is already enabled.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for CN1000Q adapter
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of kdump environment the function may be in unknown state.
Reset the function using PCI FLR before initializing it.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow minimum bandwidth to be set zero
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its now illegal to call netif_stop_queue() before register_netdev()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
4095 vlan id is reserved and should not be use.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In failover bonding case, same mac address can be programmed on other slave function.
Fw will delete old entry (original func) associated with that mac address.
Need to reporgram mac address, if failover again happen to original function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just rename all P3 #define to P3P.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anirban Chakraborty