Don't declare variable sized array of iovecs on the stack since this
could cause stack overflow if msg->msgiovlen is large. Instead, coalesce
the user-supplied data into a new buffer and use a single iovec for it.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing check for capable(CAP_NET_ADMIN) in SIOCSIFADDR operation.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later parts of econet_sendmsg() rely on saddr != NULL, so return early
with EINVAL if NULL was passed otherwise an oops may occur.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements transmit packet steering (XPS) for multiqueue
devices. XPS selects a transmit queue during packet transmission based
on configuration. This is done by mapping the CPU transmitting the
packet to a queue. This is the transmit side analogue to RPS-- where
RPS is selecting a CPU based on receive queue, XPS selects a queue
based on the CPU (previously there was an XPS patch from Eric
Dumazet, but that might more appropriately be called transmit completion
steering).
Each transmit queue can be associated with a number of CPUs which will
use the queue to send packets. This is configured as a CPU mask on a
per queue basis in:
/sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
The mappings are stored per device in an inverted data structure that
maps CPUs to queues. In the netdevice structure this is an array of
num_possible_cpu structures where each structure holds and array of
queue_indexes for queues which that CPU can use.
The benefits of XPS are improved locality in the per queue data
structures. Also, transmit completions are more likely to be done
nearer to the sending thread, so this should promote locality back
to the socket on free (e.g. UDP). The benefits of XPS are dependent on
cache hierarchy, application load, and other factors. XPS would
nominally be configured so that a queue would only be shared by CPUs
which are sharing a cache, the degenerative configuration woud be that
each CPU has it's own queue.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR test
with 1 byte req. and resp.
bnx2x on 16 core AMD
XPS (16 queues, 1 TX queue per CPU) 1234K at 100% CPU
No XPS (16 queues) 996K at 100% CPU
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_pick_tx, don't do work in calculating queue
index or setting
the index in the sock unless the device has more than one queue. This
allows the sock to be set only with a queue index of a multi-queue
device which is desirable if device are stacked like in a tunnel.
We also allow the mapping of a socket to queue to be changed. To
maintain in order packet transmission a flag (ooo_okay) has been
added to the sk_buff structure. If a transport layer sets this flag
on a packet, the transmit queue can be changed for the socket.
Presumably, the transport would set this if there was no possbility
of creating OOO packets (for instance, there are no packets in flight
for the socket). This patch includes the modification in TCP output
for setting this flag.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)
scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_sk_mc_lock rwlock becomes a spinlock.
readers (inet6_mc_check()) now takes rcu_read_lock() instead of read
lock. Writers dont need to disable BH anymore.
struct ipv6_mc_socklist objects are reclaimed after one RCU grace
period.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using AP VLAN interfaces, each VLAN interface should be in its own
broadcast domain. Hostapd achieves this by assigning different GTKs to
different AP VLAN interfaces.
However, mac80211 drivers are not aware of AP VLAN interfaces and as
such mac80211 sends the GTK to the driver in the context of the base AP
mode interface. This causes problems when multiple AP VLAN interfaces
are used since the driver will use the same key slot for the different
GTKs (there's no way for the driver to distinguish the different GTKs
from different AP VLAN interfaces). Thus, only the clients associated
to one AP VLAN interface (the one that was created last) can actually
use broadcast traffic.
Fix this by not programming any GTKs for AP VLAN interfaces into the hw
but fall back to using software crypto. The GTK for the underlying AP
interface is still sent to the driver.
That means, broadcast traffic to stations associated to an AP VLAN
interface is encrypted in software whereas broadcast traffic to
stations associated to the non-VLAN AP interface is encrypted in
hardware.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be required in the next patch and it makes the
next patch easier to review.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used earlier in the next few patches.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Also, use the ccflags-$ flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched.
Last but not least, took out if-conditionals.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Also, use the ccflags-$ flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched.
Last but not least, took out if-conditionals.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unloading pktgen module needs ~6 seconds on a 64 cpus machine, to stop
64 kthreads.
Add a pktgen_exiting variable to let kernel threads die faster, so that
kthread_stop() doesnt have to wait too long for them. This variable is
not tested in fast path.
Note : Before exiting from pktgen_thread_worker(), we must make sure
kthread_stop() is waiting for this thread to be stopped, like its done
in kernel/softirq.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to use __GFP_HIGHMEM in several __vmalloc() calls.
In ceph, add the missing flag.
In fib_trie.c, xfrm_hash.c and request_sock.c, using vzalloc() is
cleaner and allows using HIGHMEM pages as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_one_pg_vec_page() is supposed to return zeroed memory, so use
vzalloc() instead of vmalloc()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing doesn't use the socket data and is protected by x25_route_list_lock
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push down the bkl in the ioctls so they can be removed one at a time.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At compile time, we can replace the DIV_K instruction (divide by a
constant value) by a reciprocal divide.
At exec time, the expensive divide is replaced by a multiply, a less
expensive operation on most processors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting the translated instruction to 1 instead of 0 allows us to
remove one descrement at check time and makes codes[] array init
cleaner.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pc variable to avoid arithmetic to compute fentry at each filter
instruction. Jumps directly manipulate fentry pointer.
As the last instruction of filter[] is guaranteed to be a RETURN, and
all jumps are before the last instruction, we dont need to check filter
bounds (number of instructions in filter array) at each iteration, so we
remove it from sk_run_filter() params.
On x86_32 remove f_k var introduced in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory)
Note : We could use a CONFIG_ARCH_HAS_{FEW|MANY}_REGISTERS in order to
avoid too many ifdefs in this code.
This helps compiler to use cpu registers to hold fentry and A
accumulator.
On x86_32, this saves 401 bytes, and more important, sk_run_filter()
runs much faster because less register pressure (One less conditional
branch per BPF instruction)
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
2948 0 0 2948 b84 net/core/filter.o
3349 0 0 3349 d15 net/core/filter_pre.o
on x86_64 :
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
5173 0 0 5173 1435 net/core/filter.o
5224 0 0 5224 1468 net/core/filter_pre.o
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning for sk_filter_rcu_release():
Warning(net/core/filter.c:586): missing initial short description on line:
* sk_filter_rcu_release: Release a socket filter by rcu_head
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When NF_CONNTRACK is enabled, IP_VS uses conntrack symbols.
Therefore IP_VS can't be linked statically when conntrack
is built modular.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
irttp_data_request() returns meaningful errorcodes, while irttp_udata_request()
just returns -1 in similar situations. Sync the two and the loglevels of the
accompanying output.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose reachable and retrans timer values in msecs instead of jiffies.
Both timer values are already exposed as msecs in the neighbour table
netlink interface.
The creation timestamp format with increased precision is kept but
cleaned up.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IFLA_PROTINFO exposes timer related per device settings in jiffies.
Change it to expose these values in msecs like the sysctl interface
does.
I did not find any users of IFLA_PROTINFO which rely on any of these
values and even if there are, they are likely already broken because
there is no way for them to reliably convert such a value to another
time format.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMP allocates MTU sized skbs. This may fail for large MTU (order-2
allocations), so add a fallback to try lower sizes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_S_* are used internally, should not be exposed to the others.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since repeating u16 value to u8 value conversion using switch() clause's
case statement is wasteful, this patch introduces u16 to u8 mapping table
and removes most of case statements. As a result, the size of net/core/filter.o
is reduced by about 29% on x86.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to set skb priority to pktgen. Useful for testing
QOS features. Also by running pktgen on the vlan device the
qdisc on the real device can be tested.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).
The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().
This resolves the following error report.
ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
[<ffffffff8121c940>] kobject_init+0x3a/0x83
[<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
[<ffffffff8107b800>] ? mark_lock+0x21/0x267
[<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
[<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
[<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
[<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
[<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes whitespace noise introduced in commit "dccp ccid-2: Algorithm to
update buffer state", 5753fdfe8b, 14 Nov 2010.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating in_dev->mc_list from bonding driver, its better
to call a helper function provided by igmp.c
Details of implementation (locking) are private to igmp code.
ip_mc_rejoin_group(struct ip_mc_list *im) becomes
ip_mc_rejoin_groups(struct in_device *in_dev);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows wireless-testing 9236d838c9
("cfg80211: fix extension channel checks to initiate communication") and
fixes accidental case fall-through. Without this fix, HT40 is entirely
blocked.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code to handle powersaving stations has a race:
when the powersave flag is lifted from a station,
we could transmit a packet that is being processed
for TX at the same time right away, even if there
are other frames queued for it. This would cause
frame reordering. To fix this, lift the flag only
under the appropriate lock that blocks TX.
Additionally, the code to allow drivers to block a
station while frames for it are on the HW queue is
never re-enabled the station, so traffic would get
stuck indefinitely. Fix this by clearing the flag
for this appropriately.
Finally, as an optimisation, don't do anything if
the driver unblocks an already unblocked station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
snprintf() returns number of bytes that were copied if there is no overflow.
This code uses return value as number of copied bytes. Theoretically format
string '%lu.%09lu %pI4:%u %pI4:%u %d %#x %#x %u %u %u %u\n' may be expanded
up to 163 bytes. In reality tv.tv_sec is just few bytes instead of 20, 2 ports
are just 5 bytes each instead of 10, length is 5 bytes instead of 10. The rest
is an unstrusted input. Theoretically if tv_sec is big then copy_to_user() would
overflow tbuf.
tbuf was increased to fit in 163 bytes. snprintf() is used to follow return
value semantic.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).
The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().
This resolves the following error report.
ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
[<ffffffff8121c940>] kobject_init+0x3a/0x83
[<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
[<ffffffff8107b800>] ? mark_lock+0x21/0x267
[<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
[<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
[<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
[<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
[<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_cmsg_rdma_args(), the user-provided args->nr_local value is
restricted to less than UINT_MAX. This seems to need a tighter upper
bound, since the calculation of total iov_size can overflow, resulting
in a small sock_kmalloc() allocation. This would probably just result
in walking off the heap and crashing when calling rds_rdma_pages() with
a high count value. If it somehow doesn't crash here, then memory
corruption could occur soon after.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 already exposes some address family data via netlink in the
IFLA_PROTINFO attribute if RTM_GETLINK request is sent with the
address family set to AF_INET6. We take over this format and
reuse all the code.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the AF_INET link address family exposing the per
device configuration settings via netlink using the attribute
IFLA_INET_CONF.
The format of IFLA_INET_CONF differs depending on the direction
the attribute is sent. The attribute sent by the kernel consists
of a u32 array, basically a 1:1 copy of in_device->cnf.data[].
The attribute expected by the kernel must consist of a sequence
of nested u32 attributes, each representing a change request,
e.g.
[IFLA_INET_CONF] = {
[IPV4_DEVCONF_FORWARDING] = 1,
[IPV4_DEVCONF_NOXFRM] = 0,
}
libnl userspace API documentation and example available from:
http://www.infradead.org/~tgr/libnl/doc-git/group__link__inet.html
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each net_device contains address family specific data such as
per device settings and statistics. We already expose this data
via procfs/sysfs and partially netlink.
The netlink method requires the requester to send one RTM_GETLINK
request for each address family it wishes to receive data of
and then merge this data itself.
This patch implements a new API which combines all address family
specific link data in a new netlink attribute IFLA_AF_SPEC.
IFLA_AF_SPEC contains a sequence of nested attributes, one for each
address family which in turn defines the structure of its own
attribute. Example:
[IFLA_AF_SPEC] = {
[AF_INET] = {
[IFLA_INET_CONF] = ...,
},
[AF_INET6] = {
[IFLA_INET6_FLAGS] = ...,
[IFLA_INET6_CONF] = ...,
}
}
The API also allows for address families to implement a function
which parses the IFLA_AF_SPEC attribute sent by userspace to
implement address family specific link options.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tcp_connect code completely ignores errors from sending an skb.
This makes sense in many situations (like -ENOBUFFS) but I want to be able to
immediately fail connections if they are denied by the SELinux netfilter hook.
Netfilter does not normally return ECONNREFUSED when it drops a packet so we
respect that error code as a final and fatal error that can not be recovered.
Based-on-patch-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SELinux would like to pass certain fatal errors back up the stack. This patch
implements the generic netfilter support for this functionality.
Based-on-patch-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in a mode that initiates communication and using
HT40 we should fail if we cannot use both primary and secondary
channels to initiate communication. Our current ht40 allowmap
only covers STA mode of operation, for beaconing modes we need
a check on the fly as the mode of operation is dynamic and
there other flags other than disable which we should read
to check if we can initiate communication.
Do not allow for initiating communication if our secondary HT40
channel has is either disabled, has a passive scan flag, a
no-ibss flag or is a radar channel. Userspace now has similar
checks but this is also needed in-kernel.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
otherwise xfrm_lookup will fail to find correct policy
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sockets refcount is usually 2, unless an incoming frame is going to
be queued in receive or backlog queue.
Using atomic_inc_not_zero_hint() permits to reduce latency, because
processor issues less memory transactions.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now vlan are lockless, we dont need special ndo_select_queue() logic.
dev_pick_tx() will do the multiqueue stuff on the real device transmit.
Suggested-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.
This patch completely removes locking in TX path.
tx stat counters are added into existing percpu stat structure, renamed
from vlan_rx_stats to vlan_pcpu_stats.
Note : this partially reverts commit 2e59af3dcb (vlan: multiqueue vlan
device)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Version 4 of this patch.
Change notes:
1) Removed extra memset. Didn't think kcalloc added a GFP_ZERO the way kzalloc did :)
Summary:
It was shown to me recently that systems under high load were driven very deep
into swap when tcpdump was run. The reason this happened was because the
AF_PACKET protocol has a SET_RINGBUFFER socket option that allows the user space
application to specify how many entries an AF_PACKET socket will have and how
large each entry will be. It seems the default setting for tcpdump is to set
the ring buffer to 32 entries of 64 Kb each, which implies 32 order 5
allocation. Thats difficult under good circumstances, and horrid under memory
pressure.
I thought it would be good to make that a bit more usable. I was going to do a
simple conversion of the ring buffer from contigous pages to iovecs, but
unfortunately, the metadata which AF_PACKET places in these buffers can easily
span a page boundary, and given that these buffers get mapped into user space,
and the data layout doesn't easily allow for a change to padding between frames
to avoid that, a simple iovec change is just going to break user space ABI
consistency.
So I've done this, I've added a three tiered mechanism to the af_packet set_ring
socket option. It attempts to allocate memory in the following order:
1) Using __get_free_pages with GFP_NORETRY set, so as to fail quickly without
digging into swap
2) Using vmalloc
3) Using __get_free_pages with GFP_NORETRY clear, causing us to try as hard as
needed to get the memory
The effect is that we don't disturb the system as much when we're under load,
while still being able to conduct tcpdumps effectively.
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending zero byte packets is not neccessarily an error (AF_INET accepts it,
too), so just apply a shortcut. This was discovered because of a non-working
software with WINE. See
http://bugs.winehq.org/show_bug.cgi?id=19397#c86http://thread.gmane.org/gmane.linux.irda.general/1643
for very detailed debugging information and a testcase. Kudos to Wolfgang for
those!
Reported-by: Wolfgang Schwotzer <wolfgang.schwotzer@gmx.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Mike Evans <mike.evans@cardolan.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "netif_get_vlan_features" [drivers/net/xen-netfront.ko] undefined!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_port_get() renamed to br_port_get_rtnl() to make clear RTNL is held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro br_port_exists() is not enough protection when only
RCU is being used. There is a tiny race where other CPU has cleared port
handler hook, but is bridge port flag might still be set.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add br_should_route_hook_t typedef, this is the only way we can
get a clean RCU implementation for function pointer.
Move route_hook to location where it is used.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add modern __rcu annotatations to bridge multicast table.
Use newer hlist macros to avoid direct access to hlist internals.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move RX queue allocation to alloc_netdev_mq and freeing of
the queues to free_netdev (symmetric to TX queue allocation). Each
kobject RX queue takes a reference to the queue's device so that the
device can't be freed before all the kobjects have been released-- this
obviates the need for reference counts specific to RX queues.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX queues are now allocated in alloc_netdev_mq and freed in
free_netdev.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE Key field is intended to be used for identifying an individual
traffic flow within a tunnel. It is useful to be able to have XFRM
policy selector matches to have different policies for different
GRE tunnels.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/8021q/vlanproc.c: In function 'vlandev_seq_show':
net/8021q/vlanproc.c:283:20: warning: unused variable 'fmt'
Signed-off-by: David S. Miller <davem@davemloft.net>
crypto_free_cipher() is a wrapper around crypto_free_tfm() which is a
wrapper around crypto_destroy_tfm() and the latter can handle being passed
a NULL pointer, so checking for NULL in the
ieee80211_aes_key_free()/ieee80211_aes_cmac_key_free() wrappers around
crypto_free_cipher() is pointless and just increase object code size
needlesly and makes us execute extra test/branch instructions that we
don't need.
Btw; don't we have to many wrappers around wrappers ad nauseam here?
Anyway, this patch removes the redundant conditionals.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- reduce the number of retransmission attempts for sample rates
- sample lower rates less often
- do not use RTS/CTS for sampling frames
- increase the time between sampling attempts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everyone's doing it, its the cool thing.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the worst case you are seeing really odd things you want
more information than what is provided right now, for those
that insist and want debug info through CONFIG_CFG80211_REG_DEBUG
provide a print of when we are processing a channel and with what
regulatory rule.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can help with debugging issues. You will only see
these with CONFIG_CFG80211_REG_DEBUG enabled.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a module loads you will have loaded the world roaming regulatory
domain or a custom regulatory domain. Further regulatory hints are
welcomed and should be respected unless the regulatory hint is coming
from a country IE as the IEEE spec allows for a country IE to be a subset
of what is allowed by the local regulatory agencies.
So disable all channels that do not fit a regulatory domain sent
from a unless the hint is from a country IE and the country IE had
no information about the band we are currently processing.
This fixes a few regulatory issues, for example for drivers that depend
on CRDA and had no 5 GHz freqencies allowed were not properly disabling
5 GHz at all, furthermore it also allows users to restrict devices
further as was intended.
If you recieve a country IE upon association we will also disable the
channels that are not allowed if the country IE had at least one
channel on the respective band we are procesing.
This was the original intention behind this design but it was
completely overlooked...
Cc: David Quan <david.quan@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required later.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following code is defined but never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that VLAN packets are tagged in dev_hard_start_xmit()
at the bottom of the stack we no longer need to tag them
in the 8021Q module (Except in the !VLAN_FLAG_REORDER_HDR
case).
This allows the accel path and non accel paths to be consolidated.
Here the vlan_tci in the skb is always set and we allow the
stack to add the actual tag in dev_hard_start_xmit().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the headroom to be smaller then the
hard_header_len for a short period of time after toggling
the vlan offload setting.
This is not a hard error and skb_cow_head is called in
__vlan_put_tag() to resolve this.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toggling the vlan tx|rx hw offloads needs to set the hard_header_len
as well otherwise we end up using LL_RESERVED_SPACE incorrectly.
This results in pskb_expand_head() being used unnecessarily.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use vlan_features to check for TSO support if there is
a vlan tag. However, it's quite likely that the NIC is not able to
do TSO when there is an arbitrary number of tags. Therefore if there
is more than one tag (in-band or out-of-band), fall back to software
emulation.
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume that hardware TSO can't support multiple levels of vlan tags
but we allow it to be done. Therefore, enable GSO to parse these tags
so we can fallback to software.
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking if it is necessary to linearize a packet, we currently
use vlan_features if the packet contains either an in-band or out-
of-band vlan tag. However, in-band tags aren't special in any way
for scatter/gather since they are part of the packet buffer and are
simply more data to DMA. Therefore, only use vlan_features for out-
of-band tags, which could potentially have some interaction with
scatter/gather.
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/igmp.c: In function 'ip_mc_inc_group':
net/ipv4/igmp.c:1228: error: implicit declaration of function 'for_each_pmc_rtnl'
net/ipv4/igmp.c:1228: error: expected ';' before '{' token
net/ipv4/igmp.c: In function 'ip_mc_unmap':
net/ipv4/igmp.c:1333: error: expected ';' before 'igmp_group_dropped'
...
Move for_each_pmc_rcu and for_each_pmc_rtnl macro definitions
outside of multicast ifdef protection.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces an almost identical replication of code: large parts
of dccp_parse_options() re-appeared as ccid2_ackvector() in ccid2.c.
Apart from the duplication, this caused two more problems:
1. CCIDs should not need to be concerned with parsing header options;
2. one can not assume that Ack Vectors appear as a contiguous area within an
skb, it is legal to insert other options and/or padding in between. The
current code would throw an error and stop reading in such a case.
Since Ack Vectors provide CCID-specific information, they are now processed
by the CCID directly, separating this functionality from the main DCCP code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This removes
* functions for which updates have been provided in the preceding patches and
* the @av_vec_len field - it is no longer necessary since the buffer length is
now always computed dynamically.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The problem with Ack Vectors is that
i) their length is variable and can in principle grow quite large,
ii) it is hard to predict exactly how large they will be.
Due to the second point it seems not a good idea to reduce the MPS; in
particular when on average there is enough room for the Ack Vector and an
increase in length is momentarily due to some burst loss, after which the
Ack Vector returns to its normal/average length.
The solution taken by this patch is to subtract a minimum-expected Ack Vector
length from the MPS, and to defer any larger Ack Vectors onto a separate
Sync - but only if indeed there is no space left on the skb.
This patch provides the infrastructure to schedule Sync-packets for transporting
(urgent) out-of-band data. Its signalling is quicker than scheduling an Ack, since
it does not need to wait for new application data.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This aggregates Ack Vector processing (handling input and clearing old state)
into one function, for the following reasons and benefits:
* all Ack Vector-specific processing is now in one place;
* duplicated code is removed;
* ensuring sanity: from an Ack Vector point of view, it is better to clear the
old state first before entering new state;
* Ack Event handling happens mostly within the CCIDs, not the main DCCP module.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch updates the code which registers new packets as received, using the
new circular buffer interface. It contributes a new algorithm which
* supports both tail/head pointers and buffer wrap-around and
* deals with overflow (head/tail move in lock-step).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This provides a routine to consistently update the buffer state when the
peer acknowledges receipt of Ack Vectors; updating state in the list of Ack
Vectors as well as in the circular buffer.
While based on RFC 4340, several additional (and necessary) precautions were
added to protect the consistency of the buffer state. These additions are
essential, since analysis and experience showed that the basic algorithm was
insufficient for this task (which lead to problems that were hard to debug).
The algorithm now
* deals with HC-sender acknowledging to HC-receiver and vice versa,
* keeps track of the last unacknowledged but received seqno in tail_ackno,
* has special cases to reset the overflow condition when appropriate,
* is protected against receiving older information (would mess up buffer state).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
can-bcm: fix minor heap overflow
gianfar: Do not call device_set_wakeup_enable() under a spinlock
ipv6: Warn users if maximum number of routes is reached.
docs: Add neigh/gc_thresh3 and route/max_size documentation.
axnet_cs: fix resume problem for some Ax88790 chip
ipv6: addrconf: don't remove address state on ifdown if the address is being kept
tcp: Don't change unlocked socket state in tcp_v4_err().
x25: Prevent crashing when parsing bad X.25 facilities
cxgb4vf: add call to Firmware to reset VF State.
cxgb4vf: Fail open if link_start() fails.
cxgb4vf: flesh out PCI Device ID Table ...
cxgb4vf: fix some errors in Gather List to skb conversion
cxgb4vf: fix bug in Generic Receive Offload
cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
ixgbe: Look inside vlan when determining offload protocol.
bnx2x: Look inside vlan when determining checksum proto.
vlan: Add function to retrieve EtherType from vlan packets.
virtio-net: init link state correctly
ucc_geth: Fix deadlock
ucc_geth: Do not bring the whole IF down when TX failure.
...
On 64-bit platforms the ASCII representation of a pointer may be up to 17
bytes long. This patch increases the length of the buffer accordingly.
http://marc.info/?l=linux-netdev&m=128872251418192&w=2
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives users at least some clue as to what the problem
might be and how to go about fixing it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.
Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9e7
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")
The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.
Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Use modern RCU API / annotations for net_families array.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now with improved comma support.
On parsing malformed X.25 facilities, decrementing the remaining length
may cause it to underflow. Since the length is an unsigned integer,
this will result in the loop continuing until the kernel crashes.
This patch adds checks to ensure decrementing the remaining length does
not cause it to wrap around.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameter 'len' is size_t type so it will never get negative.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.
Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.
The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of FRAG6_CB(prev)->offset is int, skb->len is *unsigned* int,
and offset is int.
Without this patch, type conversion occurred to this expression, when
(FRAG6_CB(prev)->offset + prev->len) is less than offset.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Steve Chen, since commit
f5fff5dc8a ("tcp: advertise MSS
requested by user") we can end up with a situation where
tcp_select_initial_window() does a divide by a zero (or
even negative) mss value.
The problem is that sometimes we effectively subtract
TCPOLEN_TSTAMP_ALIGNED and/or TCPOLEN_MD5SIG_ALIGNED from the mss.
Fix this by increasing the minimum from 8 to 64.
Reported-by: Steve Chen <schen@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This completes the implementation of a circular buffer for Ack Vectors, by
extending the current (linear array-based) implementation. The changes are:
(a) An `overflow' flag to deal with the case of overflow. As before, dynamic
growth of the buffer will not be supported; but code will be added to deal
robustly with overflowing Ack Vector buffers.
(b) A `tail_seqno' field. When naively implementing the algorithm of Appendix A
in RFC 4340, problems arise whenever subsequent Ack Vector records overlap,
which can bring the entire run length calculation completely out of synch.
(This is documented on http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/\
ack_vectors/tracking_tail_ackno/ .)
(c) The buffer length is now computed dynamically (i.e. current fill level),
as the span between head to tail.
As a result, dccp_ackvec_pending() is now simpler - the #ifdef is no longer
necessary since buf_empty is always true when IP_DCCP_ACKVEC is not configured.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch
* separates Ack Vector housekeeping code from option-insertion code;
* shifts option-specific code from ackvec.c into options.c;
* introduces a dedicated routine to take care of the Ack Vector records;
* simplifies the dccp_ackvec_insert_avr() routine: the BUG_ON was redundant,
since the list is automatically arranged in descending order of ack_seqno.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch brings the Ack Vector interface up to date. Its main purpose is
to lay the basis for the subsequent patches of this set, which will use the
new data structure fields and routines.
There are no real algorithmic changes, rather an adaptation:
(1) Replaced the static Ack Vector size (2) with a #define so that it can
be adapted (with low loss / Ack Ratio, a value of 1 works, so 2 seems
to be sufficient for the moment) and added a solution so that computing
the ECN nonce will continue to work - even with larger Ack Vectors.
(2) Replaced the #defines for Ack Vector states with a complete enum.
(3) Replaced #defines to compute Ack Vector length and state with general
purpose routines (inlines), and updated code to use these.
(4) Added a `tail' field (conversion to circular buffer in subsequent patch).
(5) Updated the (outdated) documentation for Ack Vector struct.
(6) All sequence number containers now trimmed to 48 bits.
(7) Removal of unused bits:
* removed dccpav_ack_nonce from struct dccp_ackvec, since this is already
redundantly stored in the `dccpavr_ack_nonce' (of Ack Vector record);
* removed Elapsed Time for Ack Vectors (it was nowhere used);
* replaced semantics of dccpavr_sent_len with dccpavr_ack_runlen, since
the code needs to be able to remember the old run length;
* reduced the de-/allocation routines (redundant / duplicate tests).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]
We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
packet_getname_spkt() doesn't initialize all members of sa_data field of
sockaddr struct if strlen(dev->name) < 13. This structure is then copied
to userland. It leads to leaking of contents of kernel stack memory.
We have to fully fill sa_data with strncpy() instead of strlcpy().
The same with packet_getname(): it doesn't initialize sll_pkttype field of
sockaddr_ll. Set it to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possibility malicious users can get limited information about
uninitialized stack mem array. Even if sk_run_filter() result is bound
to packet length (0 .. 65535), we could imagine this can be used by
hostile user.
Initializing mem[] array, like Dan Rosenberg suggested in his patch is
expensive since most filters dont even use this array.
Its hard to make the filter validation in sk_chk_filter(), because of
the jumps. This might be done later.
In this patch, I use a bitmap (a single long var) so that only filters
using mem[] loads/stores pay the price of added security checks.
For other filters, additional cost is a single instruction.
[ Since we access fentry->k a lot now, cache it in a local variable
and mark filter entry pointer as const. -DaveM ]
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes ax25_getname() doesn't initialize all members of fsa_digipeater
field of fsa struct, also the struct has padding bytes between
sax25_call and sax25_ndigis fields. This structure is then copied to
userland. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commit ef885afbf8 (net: use rcu_barrier() in
rollback_registered_many)
dst_dev_event() scans a garbage dst list that might be feeded by various
network notifiers at device dismantle time.
Its important to call dst_dev_event() after other notifiers, or we might
enter the infamous msleep(250) in netdev_wait_allrefs(), and wait one
second before calling again call_netdevice_notifiers(NETDEV_UNREGISTER,
dev) to properly remove last device references.
Use priority -10 to let dst_dev_notifier be called after other network
notifiers (they have the default 0 priority)
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structure sockaddr_tipc is copied to userland with padding bytes after
"id" field in union field "name" unitialized. It leads to leaking of
contents of kernel stack memory. We have to initialize them to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce long formats.
Align arguments.
Remove KERN_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville