The WM9705 and WM9703 ops are the same actually so use
the same code for both.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When runtime->periods == 1 or when pointer crosses end of ring buffer,
the delta might be greater than buffer_size.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The HDA_SUBDEV_NID_FLAG is duplicate for amplifier control elements. Move
get_amp_nid_() call to the snd_hda_ctl_add() function.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The purpose of this changeset is to show information about amplifier
setting in the codec proc file. Something like:
Control: name="Front Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Control: name="Front Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This set of changes add missing NID values to some static control
elemenents. Also, it handles all "Capture Source" or "Input Source"
controls.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
The pin config provided by BIOS have some problems:
0x0221401f: [Jack] HP Out at Ext Front <-- other association and sequence
0x02a19020: [Jack] Mic at Ext Front <-- other association
0x01113014: [Jack] Speaker at Ext Rear <-- line out (not speaker)
0x01114010: [Jack] Speaker at Ext Rear <-- line out
0x01a19030: [Jack] Mic at Ext Rear <-- other association
0x01111012: [Jack] Speaker at Ext Rear <-- line out
0x01116011: [Jack] Speaker at Ext Rear <-- line out
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x01451140: [Jack] SPDIF Out at Ext Rear
0x40f000f0: [N/A] Other at Ext N/A
just overwrite it.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs without EPSS support (G45/IbexPeak), the hotplug event will
be lost if the HDA is powered off during the time. After that the pin
presence detection verb returns inaccurate info.
So always power-on HDA link for !EPSS codecs.
KarL offers the fact and Takashi recommends to flag hda_bus. Thanks!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timer stop callback can be called from snd_timer_interrupt(), which
is called from the hrtimer callback. Since hrtimer_cancel() waits for
the callback completion, this eventually results in a lock-up.
This patch fixes the problem by just toggling a flag at stop callback
and call hrtimer_cancel() later.
Reported-and-tested-by: Wojtek Zabolotny <W.Zabolotny@elka.pw.edu.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IbexPeak is the first Intel HDMI audio codec to support channel mapping.
Currently the outstanding problem is, the HDMI channel order do not
agree with that of ALSA. This patch presents workaround for some
typical use cases. It gives priority to the typical ALSA surround
configurations, and defines channel mapping for them.
We may need better kernel+userspace interactive channel mapping scheme.
For example, in current scheme if user plays with the surround50 device,
the kernel is unaware of this and will still select the surround41
channel allocation and channel mapping..
Thanks to Marcin for offering good tips!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA036-A specifies that the Audio Sample Packet (ASP) Channel Mapping
verbs apply to Digital Display Pin Complex instead of Converter.
With this fix, channel mapping is working as expected for IbexPeak.
Thanks to Marcin for pointing this out!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA036 spec states:
DP (Display Port) indicates whether the Pin Complex Widget supports
connection to a Display Port sink. Supported if set to 1. Note that
it is possible for the pin widget to support more than one digital
display connection type, e.g. HDMI and DP bit are both set to 1.
Also export the DP pin cap in procfs.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Note that the HBR capability only applies to HDMI pin.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes an error in processing of the HP BIOS configuration to enable
GPIO based mute LED indicator control. That error causes driver to enable
such control on all HP systems with the 92HD75 IDT codecs and results in
unnecessary toggling of the GPIO on mute control manipulation.
It also adds support of the future HP BIOS configuration extension for the
named control. New configuration string has a format HP_Mute_LED_P_G
where P can be 0 or 1 and defines mute LED GPIO control state (low/high)
that corresponds to the NOT muted state of the master volume
and G is the index of the GPIO to use (0..9)
Lastly, it adds more systems to the support of the audio implementation
as found on HP B-series systems
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are build errors when building for some of the omap2/3 boards without
enabling sound:
sound/built-in.o:(.data+0x43bc): undefined reference to `soc_codec_dev_tlv320aic23'
sound/built-in.o:(.data+0x43cc): undefined reference to `tlv320aic23_dai'
Confused me quite a bit since the drivers that had references to the
codec weren't enabled. Turns out the Makefile was using the wrong
config option to enable them. Patch below.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While Linux provided an O_SYNC flag basically since day 1, it took until
Linux 2.4.0-test12pre2 to actually get it implemented for filesystems,
since that day we had generic_osync_around with only minor changes and the
great "For now, when the user asks for O_SYNC, we'll actually give
O_DSYNC" comment. This patch intends to actually give us real O_SYNC
semantics in addition to the O_DSYNC semantics. After Jan's O_SYNC
patches which are required before this patch it's actually surprisingly
simple, we just need to figure out when to set the datasync flag to
vfs_fsync_range and when not.
This patch renames the existing O_SYNC flag to O_DSYNC while keeping it's
numerical value to keep binary compatibility, and adds a new real O_SYNC
flag. To guarantee backwards compatiblity it is defined as expanding to
both the O_DSYNC and the new additional binary flag (__O_SYNC) to make
sure we are backwards-compatible when compiled against the new headers.
This also means that all places that don't care about the differences can
just check O_DSYNC and get the right behaviour for O_SYNC, too - only
places that actuall care need to check __O_SYNC in addition. Drivers and
network filesystems have been updated in a fail safe way to always do the
full sync magic if O_DSYNC is set. The few places setting O_SYNC for
lower layers are kept that way for now to stay failsafe.
We enforce that O_DSYNC is set when __O_SYNC is set early in the open path
to make sure we always get these sane options.
Note that parisc really screwed up their headers as they already define a
O_DSYNC that has always been a no-op. We try to repair it by using it for
the new O_DSYNC and redefinining O_SYNC to send both the traditional
O_SYNC numerical value _and_ the O_DSYNC one.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Use the chip->irq to check if the irq should be released so the irq is not released
if it has not been allocated.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The volume levels in original implementation are incorrect and does
not match the dB scale. The real range is linear (in the sense of
the dB scale) from 0dB to -100dB. Remove logaritmic table and make
all volumes from range 0dB..100dB.
The tests are in RedHat's bugzilla #540817.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quirk for the ALC662 found on the Intel D945GCLF2 (and possibly other)
mainboards.
Signed-off-by: David Santinoli <david@santinoli.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Confirmed from vendor and tests in RedHat bugzilla #536782 .
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wrong variable was returned in the case of an error
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I added the product IDs of the new revisions of the devices, so owners
can test whether this suffices to make them work. Patched against ALSA
snapshot 20091207.
Signed-off-by: Tobias Hansen <Tobias.Hansen at physik.uni-hamburg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Realtek codecs, a digital mic pin is connected often only to a single
ADC. But the parser tries to set up all ADCs no matter whether the
digital mic is available, and results in non-selectable input source.
This patch adds a check of input-source availability of each ADC, and
excludes ones that don't support all input sources.
Reference: Novell bnc#561235
http://bugzilla.novell.com/show_bug.cgi?id=561235
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an updated patch for the Apple iMac 9,1 model to add sound.
Original patch posted here:
http://article.gmane.org/gmane.linux.alsa.devel/61361/match=
I have been using this patch for a while now
and have to say it works vary well, except for a few minor
things:
With the iMac 24-inch 3.06GHz Intel Core 2 Duo
everything seems to be working as it should,
although I have not looked into the microphone
(never really use one, nor have any apps to test,
my guess is it doesn't work, or I never figured out how
to get it to work).
With the iMac 24-inch 2.66GHz Intel Core 2 Duo
everything is the same as with the above machine
except I'm hearing a light scratchy/distortion noise
come out of the speakers when using headphones(above machine
does not do this).
Other than that the sound level is great(especially with good Dj headphones).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PnP data on the OPTI931 and OPTI933 contains io port
range for the MC indirect registers. Use the PnP range
instead of hardwired value 0xE0E.
Also, request region of MC indirect registers so it is
marked as used to other drivers (this was missing previously).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This renames from a character / to : of controls. A / occurs below error
messages.
ASoC: Failed to create IN2RP/VXRP debugfs file
ASoC: Failed to create IN2LP/VXRN debugfs file
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When primary AC97 is not found, don't fail with tons of AC97 errors.
Assume that the card is SF64-PCR (tuner-only).
This makes the SF64-PCR radio card work "out of the box".
Also fixes a bug that can cause an oops here:
if (tea575x_tuner > 0 && (tea575x_tuner & 0x000f) < 4) {
when tea575x_tuner == 16, it passes this check and causes problems
a couple lines below:
chip->tea.ops = &snd_fm801_tea_ops[(tea575x_tuner & 0x000f) - 1];
Tested with SF64-PCR, but I don't have any of those sound or sound+radio cards
to test if I didn't break anything.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix mute state reporting in tea575x-tuner.
This fixes mute function in kradio on SF64-PCR radio card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>