The hardware automatically disables further interrupts after each event
until rearmed. This allows a delay to be injected between the occurence
of the interrupt and the running of the cleanup routine. The delay is
scaled by the descriptor backlog and then written to the INTRDELAY
register which specifies the number of microseconds to hold off
interrupt delivery after an interrupt event occurs. According to
powertop this reduces the interrupt rate from ~5000 intr/s to ~150
intr/s per without affecting throughput (simple dd to a raid6 array).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Put the ioat2 and ioat3 state machines in the halted state with all
errors cleared.
The ioat1 init path is not disturbed for stability, there are no
reported ioat1 initiaization issues.
Cc: <stable@kernel.org>
Reported-by: Roland Dreier <rdreier@cisco.com>
Tested-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Error interrupts and error completions may cause channel hangs, so
poll the channel status register after a timeout.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ioat3.2 adds xor offload support for up to 8 sources. It can also
perform an xor-zero-sum operation to validate whether all given sources
sum to zero, without writing to a destination. Xor descriptors differ
from memcpy in that one operation may require multiple descriptors
depending on the number of sources. When the number of sources exceeds
5 an extended descriptor is needed. These descriptors need to be
accounted for when updating the DMA_COUNT register.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tag completion writes for direct cache access to reduce the latency of
checking for descriptor completions.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ioat3.2 adds raid5 and raid6 offload capabilities.
Signed-off-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In order to support dynamic resizing of the descriptor ring or polling
for a descriptor in the presence of a hung channel the reset handler
needs to make progress while in a non-preemptible context. The current
workqueue implementation precludes polling channel reset completion
under spin_lock().
This conversion also allows us to return to opportunistic cleanup in the
ioat2 case as the timer implementation guarantees at least one cleanup
after every descriptor is submitted. This means the worst case
completion latency becomes the timer frequency (for exceptional
circumstances), but with the benefit of avoiding busy waiting when the
lock is contended.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The register write in ioat_dma_cleanup_tasklet is unfortunate in two
ways:
1/ It clears the extra 'enable' bits that we set at alloc_chan_resources time
2/ It gives the impression that it disables interrupts when it is in
fact re-arming interrupts
[ Impact: fix, persist the value of the chanctrl register when re-arming ]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The cleanup path makes an effort to only perform an atomic read of the
64-bit completion address. However in the 32-bit case it does not
matter if we read the upper-32 and lower-32 non-atomically because the
upper-32 will always be zero.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When first created the ioat driver was the only inhabitant of
drivers/dma/. Now, it is the only multi-file (more than a .c and a .h)
driver in the directory. Moving it to an ioat/ subdirectory allows the
naming convention to be cleaned up, and allows for future splitting of
the source files by hardware version (v1, v2, and v3).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams